DW DWC-D1362D User manual

Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
ABOUT MANUAL
User Manual
DWC-D1362D / D1363D / D1363D922
Indoor Dome Camera
11192010
e camera please read this manual carefully
e camera please read this manual care

GGDonot open or modify.
GGDonot open the case except during maintenanceand installation,
for it may bedangerous and can cause damages.
GDonot put objects into the unit.
GGGG
or other damages.
GGGBe careful when handling the unit.
Toprevent damages, do not drop the camera or subjectit to shockor vibration.

Protectfrom humidity and dust.
Protectfrom high temperature.

Be careful when installing near the ceiling of akitchen or aboiler room,as the temperature may rise to
high levels.
Cleaning
Toremovedirt from the case, moisten asoft cloth with asoft detergent solution and wipe.
Mounting Surface
The material of the mounting surfacemust bestrong enough to support the camera.GGGGGGGGGGGGGGGGGGGGGGGGGGGG
PRECAUTIONS
This equipment has been tested and found to complywith the limits for aClass Bdigital device, pursuant
to Part 15 of the FCC rules. These limits are designed to provide reasonableprotection against harmful
interference, when the equipment is operated in aresidential environment. This equipment generates, uses,
and radiates radio frequencyenergy; and if it is not installed and used in accordancewith the instruction
manual,it may cause harmful interferenceto radio communications.
WARNING:
FCC COMPLIANCE
2

Before sending your camera for repair, checkthe following or contactour technical specialist.
No Video
Checkthe coaxial cableand make sure it is connected securely.
Checkthe lens’ iris adjustment at the menu setup of the camera.
Checkthe power supplyand make sure the camera has the proper voltage and current.
Out-of-Focus Video
Checkthe lens manual focal and zoom adjustment. Fieldtest monitor is recommended.
TROUBSHOOTING
1/3”Sony Super HAD CCD
540TV Lines
3.3~12mm Varifocal Auto Iris Lens
Electronic Day and Night
DRC (Dynamic Range Compressor)
HME (Highlight Masking Exposure)
SLC (Side Light Compensation)
AGC / BLC / AWB
NegativeImaging
Mirror Image Control
FEATURES*- D1362D
3
RS485 Built-In
ProgrammablePrivacyZone (4) & Motion Detection
Easy Icon Driven OSD Menu with Built-InJoystick
Secondary Video-BNC Output

4
1/3”Sony Super HAD II CCD
GGHigh Resolution 560 TVLines

3.3~12mm Varifocal Auto Iris Lens [D1363D]
9~22mm Varifocal Auto Iris Lens [D1363D922]
Electronic Day and Night
Star-Light (Super LowLight Technology)
DRC (Dynamic Range Compressor)
3D-DNR (3D Digital Noise Reduction)
HME (Highlight Mask Exposure)
Negative Imaging
AGC /BLC /AWB
Programmable Privacy Zone (6)&Motion Detection
Easy Icon Driven OSD Menu with Built-In Joystick
Auto Sensing 12VDC or 24VAC with Line Lock
Secondary Video-BNC Output
FEATURES*- D1363D,D1363D922

5
DIMENSIONS INMILLIMETERS*
85.0
46.5
1 23.8
R43.0
82.5
88.0
5.0
7.0
46.588.0
VIDEO (YELLOW)
BNC JACK
REDDC12V&AC24V
BLACK 0.2 INCHES(0.5mm)
TWIST SOLDERING

6
POWER REQUIREMENT*
Maximum Wire Distance
Wire Gauge 12VDC 24VAC
24 AWG 80ft 323ft
22 AWG 128ft 513ft
20 AWG 203ft 815ft
18 AWG 323ft 1295ft
16AWG 514ft 2056ft
14 AWG 816ft 3264ft
12AWG 1295ft 5183ft
10AWG 2057ft 8228ft
Coaxial Cable Type Maximum Distance
RG59/U 750ft
RG6/U 1,000ft
RG11/U 1,500ft
Power Requirement
12VDC at 1A
24VAC at 500mA

7
INSTALLATION*
Included with Digital Watchdog Camera:
1.User Manual
2. Mounting Template
3.Security L-Key
4.SingleSided Hex Key
5.Secondary BNC Cablefor aFieldMonitor
6. Two(2) Screwsand Two(2) Dry Wall Anchors
Camera Installation
Use the Mounting Templage (2) when mounting the camera.
Use the Security L-Key (3) to loosen the TwoScrews(6) that secure the dome cover. Removethe
dome cover to access the inner screw holes used to mount the camera.
NOTE
1
2
34
5
6

8
INSTALLATION*
A.Loosen the Fixing Screws(A),using the L-Key.
B. Separate the Upper Case (B) from the Base (F).
C.Loosen the Inner Screws(C),using ascrew driver.
D.Detachthe Gimbal (D) from the Base (F).
E.Cut aholein the ceiling for routing the cables.
F.Placethe Base (F) horizontallyagainst the ceiling.
Drill the screw holes at the twomarked positions.
G.Pass the Power Cable(E) and Video Cable(G) from the
camera unit through the cableholein the ceiling.
H.Align the screw holes of the camera unit with the
holes in the ceiling. Secure the camera with
the twoInner Screws(C).
I.Fix the Gimbal (D) to the Base (F).
J.Install and adjust the camera unit.
K.Adjust the dome to show the lens through the
camera window.
L.. Attachthe Upper Case (B) and the Base (F).
M.Tighten the Fixing Screws(A) to fasten the Upper
Case(B) to the Base (F).
A
B
C
D
E
F
G

9
CONNECTION*
DC12V / AC24V

10
LENS ADJUSTMENT*
A.Adjust the Pan (360°) and Tilt(60°) positions.
B. Use the Zoom Lever to set the zoom position.
C.Use the Focus Lever to set the focus.
360°
60°