DXV Modulus D19050036 Series User manual

- 1 -
INSTALLATION INSTRUCTIONS
!
SAVE FOR FUTURE USE
Thank you for selecting DXV. To ensure this product is installed properly, please read these instructions carefully before you begin.
(Certain installations may require professional help.) Also be sure your installation conforms to local codes.
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
7302329-100 Rev. A (10/17)
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2017
ROUGHING-IN DIMENSIONS:
• For reference
D19050036
D19055049
RECOMMENDED TOOLS AND MATERIALS
Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing
supply stores. It is essential that the tools and materials be on hand before work is begun.
36"Single — Model D19050036 Series
49"Double —Model D19055049 Series
DXV Modulus™
Single Mirror/Double Mirror
10'
Electric
Drill Tape Measure
#8 Screws &
Wall Anchors
Level Phillips Screwdriver
Hammer
Square
36"
(914 mm)
20-1/16"
(510 mm) 18-1/8"
(460 mm)
1-9/16"
(40 mm)
49-3/16"
(1250 mm)
20-1/16"
(510 mm) 18-1/8"
(460 mm)
1-9/16"
(40 mm)

- 2 - 7302329-100 Rev. A (10/17)
In the United States:
DXV
One Centennial Avenue
Piscataway, New Jersey 08855
Attention: Director of Customer Care
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: [phone]
www.DXV.com
In Canada:
DXV
5900 Avebury Road
Mississauga, Ontario
L5R 3M3
Canada
Toll Free: 1-800-387-0369
Local: 905-306-1093
Fax: [phone]
www.DXV.ca
In Mexico:
DXV
Via Morelos 330
Col. Santa Clara Coatitla
Ecatepec, Estado de México 55540
Toll Free: 01-800-8391200
www.DXV.mx
MIRROR INSTALLATION
CARE AND CLEANING OF MIRROR
NOTE: Mirrors are equipped to operate on a built-in, 120vac powered LED Back Light which can be wired directly
behind the mirror via a switchable outlet which should be installed by an electrician before the drywall is up.
• Carefully unpack mirror, taking care not to drop or lay down on a rough surface.
• Provide suitable reinforcement required for anchoring mirror to the wall.
• Once a location is determined, use a level and tape measure to mark the mounting hole locations.
NOTE: Mirrors can be mounted either horizontally or vertically. (See Diagram A and B for dimensions)
• Mark the locations for the size and position of the mirror selected and drill a hole at these positions to accommodate the type
of wall anchor used.
NOTE: Wall anchors must have a load capacity of at least 50lbs.
• Insert the #8 screw into the wall anchors leaving approximately 1/4" of the screw head from the wall in which to hang the mirror.
• Connect the electrical hook up to the mirror.
• Hang mirror on the screws and adjust screws in or out to ensure mirror is properly and securely mounted
into the mirrors rear frame. (See Diagram B)
Clean the product by using soft, slightly damp cloth. Buff the mirror by using a soft dry cloth.
Avoid using silicone cleaners and waxes.
MIRROR
OUTLINE
D19055049
45-1/4"
(1149 mm)
D19050036
32"
(813 mm)
16-1/8" (410 mm)
FIGURE A
FIGURE B