DXV Oak Hill D19005000.620 User manual

- 1 -
INSTALLATION INSTRUCTIONS
SAVE FOR FUTURE USE
!
Thank you for selecting DXV. To ensure this product is installed properly, please read these instructions carefully before you begin.
(Certain installations may require professional help.) Also be sure your installation conforms to local codes.
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
NOTE: Pictures may not exactly define contour of mirror and components.
770234-100 Rev. A (6/17)
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2017
ROUGHING-IN DIMENSIONS:
• For reference
RECOMMENDED TOOLS AND MATERIALS
Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing
supply stores. It is essential that the tools and materials be on hand before work is begun.
Models D19005000.620
D19005000.238
Oak Hill™
Mirror
Phillips Screwdriver Regular Screwdriver Drill
10'
Tape MeasureLevel Hammer
18"
(457 mm)
2"
(51 mm)
MIRROR
30"
(762 mm)
FRONT VIEW SIDE VIEW
2"
(51 mm)
13
24
ITEM DESCRIPTION
1 Mirror
2 6 x 1-1/2 Screw
3 Wall Bracket
4 Wall Anchor
In the United States:
DXV
One Centennial Avenue
Piscataway, New Jersey 08855
Attention: Director of Customer Care
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: [phone]
www.DXV.com
In Canada:
DXV
5900 Avebury Road
Mississauga, Ontario
L5R 3M3
Canada
Toll Free: 1-800-387-0369
Local: 905-306-1093
Fax: [phone]
www.DXV.ca
In Mexico:
DXV
Via Morelos 330
Col. Santa Clara Coatitla
Ecatepec, Estado de México 55540
Toll Free: 01-800-8391200
www.DXV.mx

- 2 -
1 2
3 4
5
770234-100 Rev. A (6/17)
• Using a level, draw a 6" horizontal line 3-3/4" down from
the point marked in Step 1 as shown in Figure 2.
• Place the wall bracket on the horizontal line with the hole
side down and ush with the wall. Be sure that the center
hole is aligned with the center of the horizontal line as
shown in Figure 3.
• Trace the hole locations on the wall as shown.
• Remove the bracket and drill 1/8" holes in the marked
locations if going into wood. Drill a ¼" if attaching to dry
wall or plaster.
Note: Wall anchors must be used if hanging the mirror
on dry wall, plaster, or tile.
Note: The mirror must be hung on a wall. It is not
designed to rest on the floor or on any type of
furniture.
• Identify where the mirror is to be hung on the wall.
• Using a pencil mark the center of the top of the mirror
as shown in Figure 1.
• Install the wall anchors if they are required.
• Attach the bracket to the wall using the screws provided.
• Be sure to conrm that the bracket is level prior to
completely tightening the screws. Adjust as necessary.
• Align the bracket on the mirror with the bracket on the wall
(as shown in Figure 4) and gently slide the mirror until the
mirror bracket rests rmly on the wall bracket.
Figure 1
Figure 2
Figure 4
3-3/4"
(95 mm)
CENTER OF
6"
HORIZONTAL
LINE
MARK CENTER
OF THE TOP OF
THE MIRROR
CENTER OF
HORIZONTAL LINE
WALL BRACKET
Figure 3
MIRROR FINISHED
WALL
ANCHORS
FACTORY
INSTALLED
SCREWS
WALL BRACKET
MOUNTING BRACKET