DXV Belshire D23050A000.415 User manual

- 1 -
INSTALLATION INSTRUCTIONS
SAVE FOR FUTURE USE
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2020 7302409-100 (2/2020)
RECOMMENDED TOOLS AND MATERIALS
Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing
supply stores. It is essential that the tools and materials be on hand before work is begun.
Thank you for selecting DXV. To ensure this product is installed properly, please read these instructions carefully before you begin.
(Certain installations may require professional help.) Also be sure your installation conforms to local codes.
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
NOTE: Pictures may not exactly define contour of china and components.
!
DXV Belshire™
Wall Hung Toilet with Seat
Model D23050A000.415
Regular Screwdriver
10'
Level
Closet Bolts
Putty Knife
Tape Measure Hacksaw
SealantAdjustable Wrench
Flexible Supply Tube
ALL INSTALLATION PROCEDURES MUST COMPLY IN STRICT ACCORDANCE WITH APPLICABLE LOCAL
PLUMBING AND BUILDING CODES.
For rough-in dimensions, see spec page or web site
BOWL INSTALLATION:
Remove yellow protection plugs and seals from pipes.
Place discharge pipe with gasket into waste outlet of bowl.
Also place ush pipe with n gasket into inlet of bowl.
Then mark a second line on both pipes.
Insert discharge pipe into the pipe hub in the wall. Place
a straight edge ush against the wall and mark a line on
the pipe. Fit nned rubber seal onto ush pipe. Repeat
same procedure for discharge pipe.
Add dimension X and 1/8" (3 mm). Using that dimension,
mark a line on the pipe measuring from the hub side.
Cut off the pipe at the line with a pipe cutter.
1 2
4
3
X
X
+
1/8"
+(3mm)

- 2 -
Add dimension Y and 1/8" (3 mm). Using that dimension,
mark a line on the pipe measuring from the hub side.
Cut off the pipe at the line with a pipe cutter.
Bevel the sharp edges as shown to assure a smooth
insertion into the pipe hubs in the wall.
7302409-100 (2/2020)
5 6
+
1/8"
+(3mm)
Y
Y
Seal gap around bowl with waterproof sealant.
10
9
Install both seals into the pipes in the wall. Lubricate seals
with appropriate rubber seal lubricant.
Remove protective sleeves from threaded mounting rods.
Install rods with a protruding length of 1-3/8" (35 mm) from
the nished wall. Then install the threaded nuts leaving
approximately 3/8" (10 mm) of the threaded rod exposed.
Also insure the concave portion of the nut is facing down!
Install both pipes into the hubs in the wall.
7 8
3/8"
(10 mm)
Ensure each of the pre-installed 4 ngered plastic mounts
are securely mounted into each mounting hole of the toilet.
Place bowl onto female threaded nuts and carefully insert
bowl so the threaded female nuts go into the plastic nger
housings mounted in the toilet. Once toilet is fully mounted
into the female threaded nuts, turn the hex allen rod insert-
ed into the plastic housing clockwise to tighten toilet into
nished wall.
Female
Thread Nut
Concave
4 Fingered
plastic
mount
Hex allen
rod
Hex allen
handle

- 3 -
7302409-100 (2/2020)
In the United States:
DXV
One Centennial Avenue
Piscataway, New Jersey 08855
Attention: Director of Customer Care
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: [phone]
www.DXV.com
In Canada:
DXV
5900 Avebury Road
Mississauga, Ontario
L5R 3M3
Canada
Toll Free: 1-800-387-0369
Local: 905-306-1093
Fax: [phone]
www.DXV.ca
In Mexico:
DXV
Via Morelos 330
Col. Santa Clara Coatitla
Ecatepec, Estado de México 55540
Toll Free: 01-800-8391200
www.DXV.mx
COMPONENT NUMBER DESCRIPTION
D23050A000.415 With seat
5020A156.415. Seat
D29054026.000 Grohe In wall carrier
D28015000.415 Grohe dual ush plate
(for carrier repair parts please check carrier installation instructions)