Dymo LabelManager Wireless PnP User manual

LabelManager®Wireless PnP
Quick Start Guide
Guide de démarrage rapide
Guía de iniciación rápida
Guia de Início Rápido
ENG
ES
FR
PT

Copyright
© 2013 Sanford, L.P. All rights reserved.
No part of this document or the software may be reproduced or transmitted in any form or by any
means or translated into another language without the prior written consent of Sanford, L.P.
Trademarks
DYMO, DYMO Label, and LabelManager are registered marks in the US and other countries. All other
trademarks are the property of their respective holders.
Copyright
© 2013 Sanford, L.P. Tous droits réservés.
Aucune partie de ce document ou du logiciel ne peut être reproduite ou distribuée sous quelque
forme or par quelque moyen que ce soit ou traduite en une autre langue sans le consentement écrit
préalable de Sanford, L.P.
Marques de commerce
DYMO, DYMO Label et LabelManager sont des marques déposées aux
États-Unis d’Amérique et dans d’autres pays. Toutes les autres marques de commerce
appartiennent à leurs propriétaires respectifs.
Copyright
© 2013 Sanford, L.P. Todos los derechos reservados.
Queda totalmente prohibida la reproducción o transmisión total o parcial de este documento, en
cualquier forma o modo, así como la traducción del mismo a otro idioma sin el previo consentimiento
escrito de Sanford, L.P.
Marcas comerciales
DYMO, DYMO Label y LabelManager son marcas comerciales registradas en los EE. UU. y otros
países. Todas las demás marcas comerciales son propiedad de sus respectivos propietarios.
Copyright
© 2013 Sanford, L.P. Todos os direitos reservados.
Nenhuma parte deste documento ou do software pode ser reproduzida ou transmitida de qualquer
forma ou por qualquer meio, ou traduzida para outro idioma, sem o consentimento prévio por escrito
da Sanford, L.P.
Marcas comerciais
DYMO, DYMO Label e LabelManager são marcas registradas nos EUA e em outros países. Todas as
outras marcas comerciais pertencem a seus respectivos proprietários.

Quick Start Guide . . . . . . . . . . . . . . . . 1
Guide de démarrage rapide. . . . . . . . 15
Guía de iniciación rápida . . . . . . . . . . 29
Guia de Início Rápido . . . . . . . . . . . . 43
PT
ES
FR
ENG

1
This guide describes some of the features of your DYMO®LabelManager
Wireless PnP label maker. Read the following sections for information about
using your label maker.
Registering Your Label Maker
Getting to Know your Label Maker
Inserting the Battery Pack
Removing the Battery Pack
Inserting the Label Cassette
Connecting the Label Maker to your Computer
Starting the Built-In Software
Printing Labels with the Built-In Software
Checking the Label Maker Status
Charging the Battery Pack
Configuring the Label Maker as a Wireless Printer
Adding the Wireless Printer
Registering Your Label Maker
Visit www.dymo.com/register to register your label maker online. During the
registration process, you will need the serial number, which is located above the
label cassette inside the label maker. See Figure 1 on page 2.
Register your label maker to receive these benefits:
Email notification of free software upgrades
Special offers and new product announcements
For complete information on using your label maker, download the full
LabelManager Wireless PnP User Guide from the Support section of the Web
site at www.dymo.com.
Quick Start Guide

2
Getting to Know your Label Maker
Become familiar with the features shown in the following figure
1Side cover 5Label exit slot 9Cleaning tool
2Wireless status light 6Battery compartment 10 USB port
3Power button/status light 7Serial number label 11 Reset button
4Cutter 8Label compartment
Figure 1
6
5
4
9
7
8
1
3
10 11
Back View
2

3
Inserting the Battery Pack
The label maker is powered using a rechargeable lithium-ion polymer (LiPo)
battery pack.
Make sure the USB cable is disconnected before handling the LiPo
battery pack.
To insert the battery pack
1Press and pull to open the
side cover of the label maker.
2Insert the battery pack into the
battery compartment as shown
in Figure 2.
Make sure to read the LiPo
Safety Precautions found on
page 12.
Removing the Battery Pack
Remove the battery pack when the
label maker will not be used for more
than seven days.
Make sure the USB cable is disconnected before handling the LiPo
battery pack.
To remove the battery pack
1Unplug the USB cable.
2Press and pull to open the side cover of the label maker.
3Remove the battery pack from the battery compartment.
Make sure to read the LiPo Safety Precautions found on page 12.
Figure 2
Press
and pull

4
Inserting the Label Cassette
Your label maker uses DYMO D1
label cassettes.
To insert the label cassette
1Press and pull to open the
side cover of the label maker.
2Make sure the tape and ribbon
are taut across the mouth of the
cassette and that the tape
passes between the label
guides. See Figure 3.
If necessary, turn the ribbon
rewind spool clockwise to
tighten the ribbon.
3Insert the cassette and press
firmly until the cassette clicks
into place. See Figure 4.
4Close the side cover of the
label maker.
Figure 3
Label guides
Ribbon rewind
spool
Press
and pull
Figure 4
Click!

5
Connecting the Label Maker to your Computer
The label maker connects to your computer through the USB connection located
on the back of the label maker.
To connect the label maker to your computer
1Plug one end of the USB cable into the label maker. See Figure 5.
2Plug the other end into an available, powered
USB port on your computer.
The label maker must be connected to a
powered USB port. The label maker may not charge
or function properly when connected to a non-
powered USB port, such as those on some Mac
keyboards or a non-powered USB hub.
Starting the Built-In Software
The built-in software resides on the label maker; no installation is required.
To start the software for Windows®
1If necessary, press the power button to turn on the label maker.
Depending on Windows AutoRun or AutoPlay settings, the software may
start automatically.
2If the software does not start automatically, do one of the following:
• If the AutoRun or AutoPlay dialog box appears, follow the on-screen
instructions to start the DYMO Label Light software.
• If the AutoRun or AutoPlay dialog box does not appear, navigate to
My ComputerDYMO W-PNP, and then click DYMO Label
Light.exe.
To start the software for Mac OS®
1If necessary, press the power button to turn on the label maker.
The DYMO Wireless PnP volume appears on your desktop.
2Double-click DYMO W-PNP to open the volume.
3Double-click to start the software.
Figure 5

6
Printing Labels with the Built-In Software
The following figure shows some of the features available in the software.
To print your first label
1Click once on the label in the Edit area and type some text.
2Click to print the label.
To capture and insert an image from your desktop
1Click on the toolbar.
2Drag the curser to draw a selection box around the area to capture.
The selected area is inserted into your label.
To take advantage of more advanced formatting features, click in the built-in
software to download and install DYMO Label™ v.8.5 or later from the DYMO
Web site.
Insert text from
the Clipboard.
Select the
font, size, and
style for your
label text.
Create a
new label.
Match the label
width to the label
cassette in the
label maker.
Start advanced
DYMO Label v.8
software.
Rotate images 90
degrees.
Choose to print
a horizontal or
vertical label.
Add a border
around the label.
Choose a fixed length for the
label or make the label resize
automatically to fit the text.
Crop an image
added to the label.
Change the units of
measure or
language settings.
Capture an area of the
screen and insert on
your label.
View the power
status of the
label maker.
Print a label.
Zoom the label.
Manage the
label maker on your
wireless network.
Choose to automatically cut
each label as printed or to
only cut between print jobs.
Figure 6