Easee Equalizer Amp User guide

Equalizer Amp
EN Installer and User guide

2
Introduction
The information in this leaflet applies to Easee
Equalizer Amp , unless specified otherwise.
Read the Important product information
guide in the product packaging or at
easee.com/manuals before using the
product.
WARNINGS AND CAUTIONS
A Warning indicates a condition, hazard or
unsafe practice that can result in serious
personal injury or death.
A Caution indicates a condition, hazard
or unsafe practice that can result in minor
personal injury or damage to the product.
WARNING
This product shall only be installed, repaired
or serviced by an authorised electrician.
All applicable local, regional and national
regulations for electrical installations must
be respected.
Optimal performance
The Equalizer Amp together with the Easee
Equalizer makes it possible to charge
smarter, safer and faster without the need
of a smart meter, if the installation is scaled
accordingly.

3
Technical specifications
General
Dimensions Product 95 x 51 x 30 mm (H x W x D)
Operating temperature -20 °C to +50 °C
Weight 105 g
Supply 85-264 V AC
Installation system TT, IT or TN
Phases 1- or 3-phase
Current sensors
Type CT clamps
Operation range 0 – 100 A
Conductor diameter max. 16 mm
Cable length 1 m
Protection
Degree of protection IP30
Insulation class II
Overvoltage category OVC II
Connectivity
2 x RJ12 connectors
6 x sensor slots
1 x 12 pin expansion port

4
*Plug not included for the power cable.
Product overview
Equalizer Amp
*
Power cable
Current sensors x 3 DIN bracket
Expansion connector

5
WARNING
- This product shall only be installed,
repaired or serviced by an authorised
electrician. All applicable local,
regional and national regulations
for electrical installations must be
respected.
- Turn off the power before you begin the
installation. Use extreme caution and
follow instructions carefully.
Install the Installer App on your phone
by visiting easee.com/installer-app or
scanning the QR code.
Installation
instructions
Equalizer Amp
Mounting
1
1. Mount the Equalizer Amp on the DIN
rail (A) inside the fuse cabinet. If that’s
not possible, attach the included DIN
bracket (B) to a surface and then
mount the Equalizer Amp.
B
BA

6
Source/Grid Load/Building
Current sensors
Attaching
2
1. Attach current sensor(s) around each
conductor either in front or behind the
main fuse. The arrow on the sensor must
point towards the load.
L1
L2
L3
2. Plug the current sensors, L1, L2 and L3,
into their respective terminals 1, 2 and 3.
NOTE! Depending on national standards,
the colour of the cables can vary from
illustration.
1 2

7
1. Connect the included power cable to
a suitable power source. A separate
fuse with a maximum rating of 16 A is
recommended.
2. Find the RJ12 cable in the Equalizer box
and connect it to an RJ12 terminal on
the Equalizer Amp. The bottom RJ12
terminal is for connecting multiple
Equalizer Amps.
Equalizer Amp
Connecting
3
RJ12
3
2
1
CHECK LIST! Before powering up the
Equalizer Amp, make sure that:
o The current direction is correct on the
current sensors.
o The charging sites and the Equalizer Amp
have the same phase sequence.
o The L1 current sensor is plugged into
terminal 1, L2 sensor in terminal 2 and L3
sensor in terminal 3 on the Equalizer Amp.
3. Power up the Equalizer Amp. You should
see a flashing at the bottom right
corner of the device.

8
Use the Installer App to configure the
Equalizer on a site with multiple circuits.
Before starting, make sure that the
Equalizer and the master charger(s) are
connected to the same WiFi network. Also
make sure you have NFC enabled on your
mobile phone.
Equalizer
Setting up
41. Go to ”Ongoing sites”, or ”Update
existing site”, and select your site.
2. Under ”Site structure”, select ”Add
Equalizer”.
3. Enter the WiFi information (the same
network the chargers are connected to).
4. Hold the mobile phone to the front
of the Equalizer to transmit the WiFi
details. The Equalizer cannot receive the
information if it’s powered on.
5. Connect the Equalizer to the Equalizer
Amp with the RJ12 cable.
5
4

9
Practical details
LED colours meaning
White, fast flashing – Booting
White, breathing every 10s – Normal operation
Red / white, switching – No WiFi added
Red, flashing – No data from power meter
Red, breathing every 10s – Error
Purple, breathing every 10s – Offline operation
Warranty
The device is free from material defects and
is in accordance with laws and regulations
for consumer protection in the country where
the product is purchased. All correctly installed
Easee hardware is covered by our 3 years*
limited warranty.
*Some countries may have extended warranty.
Maintenance
This product requires no maintenance.
If it needs to be repaired, please contact your
Easee supplier.
Returns and complaints
Contact your distributor or Easee Customer
Support at easee.support regarding the return
and complaint of your product.

The information in this document is for information purposes
only, is provided as is, and may be subject to change without
notice. Easee AS including its subsidiaries does not accept any
liability for the correctness or completeness of the information
and illustrations, and is not liable or responsible for your
considerations, assessments, decisions or absence of such, or
other use of the information in this document.
No part of this publication may be re-published, reproduced,
transmitted or re-used in any other form, by any means or
in any form, for your own or any third-party’s use, unless
otherwise agreed with Easee or its subsidiaries in writing. Any
permitted use shall always be done in accordance with good
practice and ensure that no harm may be caused to Easee or
by misleading the consumer.
Easee and Easee products, product names, trademarks and
slogans, whether registered or not, are Easee’s intellectual
property and may not be used without Easee’s prior written
permission. All other products and services mentioned may be
trademarks or service marks of their respective owners.
January 2023 – Version 1.00
© 2023 by Easee AS. All rights reserved.
Easee AS
Grenseveien 19
4313 Sandnes, Norway
.easee.com