Easy@Home 2023 User manual

customerservice
@biddefordblankets.com
ITEM: 6411
AFTER SALES SUPPORT USA 800 789
6441
Contents
1 Introduction………………………2
2 General Information and Safety
Instructions……………………….2
3 Assembly and Parts
List……………………….……….4
4 Getting Started……………………5
5 Features…………………………..6
6 Instructions……………………….6
7 FAQ………………………………8
8 Other Useful Information………...9
9 Index……………………………..10
10 Warranty Card…………………...11
1

customerservice
@biddefordblankets.com
ITEM: 6411
AFTER SALES SUPPORT USA 800 789
6441
Introduction 1
Congratulations on purchasing this heated blanket! We have spent
years developing our Sensor-wire technology to provide you with a
state of the art product. You should expect to receive many years of
warmth and comfort from your blanket.
General Information and Safety
Instructions 2
IMPORTANT
SAFETY
INSTRUCTIONS
- DO NOT
DESTROY!
WARNING: Failure to follow these safety instructions may lead to
personal injury!
WARNING: To reduce this risk of fire or electrical shock:
BE SURE TO READ THE FOLLOWING INSTRUCTIONS
CAREFULLY BEFORE USING THIS BEDDING!
1. Do not use this bedding with an infant, a child, an incapacitated
or immobile person, a paraplegic or a quadriplegic, or a person
who is medicated.
2

customerservice
@biddefordblankets.com
ITEM: 6411
AFTER SALES SUPPORT USA 800 789
6441
2. Do not use this bedding if you are diabetic or insensitive to heat
or have poor blood circulation, or use it on anyone else who is a
diabetic or insensitive to heat, such as a person with poor blood
circulation.
3. Do not tuck in the wired area, fold, or bunch this bedding when
in actual use; excessive heating may result.
4. Do not tuck the bedding/control or supply cord in a sofa or other
furniture. All portions of the product and controller should be
visible at all times. Like any other electrical cord, this can cause
damage to the power cord that may result in an electrical short
that leads to a fire.
5. Do not route electrical cords between the mattress and box
spring. Do not allow the cords to be pinched, trapped, or
crossed. Like any other electrical cord, this can cause
damage to the power cord that may result in an electrical
short that leads to a fire.
6. Do not use pins - They may damage the electric wiring.
7. Be sure that this bedding is used on an alternating-current
supply circuit of the proper voltage.
8. Turn OFF or unplug when not in use.
9. Product not for use with inverter supplied power such as
from a motor home or boat.
10. This product is for in-home use only, not for hotel, motel,
or other institutional use.
11. If improper operation of this bedding is observed,
discontinue its use immediately and consult the
manufacturer.
12. Do not use with pull-out or fold-up bed. Do not use with
rocking chairs, recliners, chairs with casters or wheels, or
other furniture subject to movement. This may cause the
wires to be pinched and create an electrical fault.
13. Keep the controller away from drafty areas that may become
damp or wet such as an open window. Do not cover the
controller.
14. Wrapping of cord around the controller may damage the cord:
Loop loosely when storing.
3

customerservice
@biddefordblankets.com
ITEM: 6411
AFTER SALES SUPPORT USA 800 789
6441
15. Do not dry-clean this bedding. Cleaning solvents may have
deteriorating effects on the insulation of the heating
element.
16. This appliance has a polarized plug, (one blade is wider than the
other). As a safety feature, this plug will fit in a polarized outlet
only one way. If the plug does not fit fully in the outlet, reverse
the plug. If it still does not fit, contact a qualified electrician. Do
not attempt to defeat the safety feature.
17. Never open up the controller case. Doing so could prove
potentially hazardous and will VOID YOUR
WARRANTY!
18. Use your heated bedding ONLY with the supplied
controller.
19. Keep all animals away from your heated bedding. They
could damage the wiring, leading to a potentially harmful
situation.
If you have any questions or concerns regarding your product we
encourage you to contact our excellent Customer Service support listed
in section 8 of this manual.
Assembly and Parts List 3
All packages should include: the warming product, a warranty card, instruction
manual, and controller.
Bedding Model Controller
Model
OB TC
Twin 1 controller
Full 1 controller
Queen 2 controllers
King 2 controllers
4

customerservice
@biddefordblankets.com
ITEM: 6411
AFTER SALES SUPPORT USA 800 789
6441
Getting Started 4
1. Remove the product from the package along with the controller(s).
2. Lay the blanket out flat on the bed, with the connectors placed at
the foot of the bed. The label should always be facing UP toward the ceiling,
at the foot of the bed.
3. Securely attach the connector cord from the controller to the connector on the
product. Make sure that the connection is firmly secured. If you have a
Queen or King sized product it is not necessary to connect both sides for the
product to operate properly; however you will only receive heat to the side of
the product that is properly connected. NOTE: It does not matter which
controller is attached to which side of the product, the controllers are
interchangeable.
CAUTION! –Do not route electrical cords between the mattress and
box spring. Do not allow the cords to be pinched, trapped, or crossed.
See Safety Instructions.
CAUTION! –Do not tuck in the wired area of this bedding. See Safety
Instructions.
CAUTION! –Do not cover the controller. See Safety Instructions.
4. Insert power cord into standard 120volt wall outlet.
Blanket
Step 1-
Remove the
product from
the package
along with the
controller(s)
Step 2 - Lay the
blanket out flat
on the bed,
with the
connectors
placed at the
foot of the bed.
The label
should always
be facing UP
toward the
ceiling.
CAUTION! –Do not tuck in
the wired area of this
bedding
Step 3 - Securely attach the connector cord from the
controller to the connector on the product. Make sure
that the connection is firmly secured
Label
Controller
Connector
Cord
Step 4 –Insert power
cord into standard
120volt wall outlet
Controller
Power Cord

customerservice
@biddefordblankets.com
ITEM: 6411
AFTER SALES SUPPORT USA 800 789
6441
Features 5
Auto Off - Your heated bedding has a built-in feature called “Auto-Off”. This feature
will automatically turn off the controller after 10 hours of continuous use.
Independent Controllers –Your Queen/King size warming products come with dual
sided comfort zones; each powered and adjusted independently with a separate
controller.
Thin & Flexible Wires –Our heating and sensing wire is designed to be thin and
flexible in order to provide a higher comfort level.
Comfort beyond warmth –The heated bedding materials have a soft luxurious feel
that will have you wanting to surround yourself with your bedding even when the
extra warmth is not needed.
10 Heating Settings –You have your choice of ten levels of heating; allowing for the
perfect comfort level at any time.
Continuous Temperature Sensing –Your heated bedding uses a continuous sensing
technology which monitors, and if need be, adjusts the temperature to remain at your
chosen heat level.
Comfort Level Memory –Upon restart, the digital heated bedding controllers
automatically revert to the last comfort level setting used; allowing you to
conveniently return to your normal comfort setting.
Pre-Heat –You can preheat your bedding for up to 1.5 hours by pressing the PRE-
HEAT button.
Instructions 6
Using your Blanket DIGITAL Controller (Model#
TC16)
The very first time the blanket is plugged in and turned ON, the display on the
controller should read “4”. If the display does not illuminate or reads “E”, see the
Troubleshooting section.
Turning the Blanket “ON”
Once the cords are correctly plugged in, press the ON/OFF button. The LED display
will light up to show that the power is ON. NOTE: If you have a Queen or King sized
product, you will need to connect both controllers to heat both sides of the product;
each controller will only heat one side.
Adjusting the Temperature
To adjust the temperature setting, press one of the arrow buttons. Press the UP
arrow to increase the heat setting and the DOWN arrow to decrease it. There
are 10 settings, 1 through 9 and “H”for HIGH, the higher the number, the
warmer the product. Each time you press an arrow button the setting will adjust
by one digit. If you have a product that uses two controllers, each controller can
be adjusted to different settings, causing each side to heat differently.
6

customerservice
@biddefordblankets.com
ITEM: 6411
AFTER SALES SUPPORT USA 800 789
6441
Turning “OFF”
Turn the controller OFF manually by pressing the ON/OFF button. When the
controller is OFF but plugged in, you will see a red or green light on the controller
without the number displayed. Seeing this light alone means the controller is in
standby mode and the bedding is off and not heating. Turn OFF or unplug the
controller when not in use.
Pre-Heat (Specific Models Only)
Press the PRE-HEAT button. This will start pre-heating the bedding and “p”will be
displayed on the controller. The heat setting will change to the last setting after 1.5
hours. If you want to change to another setting during the pre-heat period, press the up
or down button.
Washing Instructions - WARNING: Failure to follow these washing
instructions may damage the product and make it unsafe.
Wash by hand or as follows in automatic washer using slow agitation and
normal spin speed:
1. Fill washer with warm water.
2. Add minimum amount of all-purpose detergent, agitate to dissolve.
3. Add bedding and soak for five minutes.
4. Agitate for two minutes.
5. Spin.
6. Fill for cool rinse.
7. Agitate one minute.
8. Spin.
9. Dry in an automatic dryer on low heat, five minutes only, or line dry.
10. Remove bedding from dryer and drape over parallel lines or a shower rail
to finish drying.
CAUTION! –Do not iron your bedding.
CAUTION! –Do not dry-clean this product. Cleaning solvents may have a
deteriorating effect on the insulation of the heating element.
CAUTION! –Do not use a wringer. You may hand wash this product.
CAUTION! –Do not dry in a commercial dryer such as those used in
Laundromats.
CAUTION! –Do not power-up this product while it is still damp. For
safety’s sake, wait until the product is completely dry before connecting it
and plugging it in.
CAUTION! –Do not use pins –they may damage the electrical wiring.
7

customerservice
@biddefordblankets.com
ITEM: 6411
AFTER SALES SUPPORT USA 800 789
6441
FAQ 7
My heated product does not seem to turn on. What do I do?
a. First, check to see if the controller is illuminated. If you see that it is
illuminated, it is receiving power. If there is no light of any type, check
the ON/OFF switch.
b. Second, if there is still no illumination, check the connections. Unplug
the cord from the wall outlet. Then check the connectors to make sure
that the controller is firmly secured. Then re-plug it into the wall outlet.
If the display lights up, it is receiving power and is ON.
c. Third, if there is still no power, disconnect the product and contact the
Customer Service support listed under section 8 of this manual.
The display is illuminated but I don’t feel it warming up. What do I do?
Please remember, automatic warming blankets are not like heating pads: Do not expect
to feel direct heat.
CAUTION! –The following troubleshooting test represents a non-standard use of
your product. Do not continue this test for more than seven (7) minutes. Do not repeat
this procedure during actual use.
Fold the product with at least four folds. Connect the controller to the
bedding, then plug the controller into a working wall outlet. Set the controller
to the highest heat setting and wait for five minutes. Place your hand inside
the folds; you should feel warmth. Turn the controller OFF. Lay the product
out flat.
d. If no heat is felt, disconnect the product and contact the Customer
Service support listed under section 8 of this manual.
The display is illuminated but it is reading “E”, what does that mean?
“E”stands for “ERROR”and indicates there may be a problem.
CAUTION! –Do not attempt to operate your product if you are getting repeated
ERROR messages.
a. Some error messages are caused by transient events and not an actual
problem. To check, turn off the product and wait 15 seconds. Then turn
the product on again.
8

customerservice
@biddefordblankets.com
ITEM: 6411
AFTER SALES SUPPORT USA 800 789
6441
b. When prongs in the connector do not make good contact with the
receptacle on the cord side, or the product is not connected to the
receptacle on the cord side, the display will read “E”. In this case, please
turn the controller off and unplug the product from the wall. Then make
sure that the product and controller connectors are firmly secured. After
that, turn the blanket ON again.
c. If the “E”returns for a second time, disconnect the product and contact
the Customer Service support listed under section 8 of this manual.
We just washed our Queen or King product, and we’re not sure which controller
goes to which side of the bedding. Does it make a difference?
No it does not. Each controller is engineered to be able to control either side
of your automatic warming product of the same size. However, make sure
you place the product in the correct position when you place it back on the
bed and follow all safety procedures in setting it up. Then connect each
controller and adjust it to your desired setting.
Other Useful Information 8
Warranty & Support
This warming product is warranted for five years against defects in materials or
workmanship. This warranty covers the electronic controller, the cords, and the
blanket itself. This warranty does not cover abuse, accident, or damage resulting from
failure to follow instructions, or modifications to the unit not carried out by the
manufacturer. Defective products must be returned to the company name and address
below. This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state.
Before sending your product in for warranty service, please contact our customer
service department below to obtain a Return
Authorization number to ensure expedited processing.
Biddeford
Blankets
Attention: Customer Service
300-302 Terrace Drive
Mundelein, IL 60060
Telephone: [phone]
9

customerservice
@biddefordblankets.com
ITEM: 6411
AFTER SALES SUPPORT USA 800 789
6441
FCC
“Caution: Unauthorized modifications could void the user’s authority to operate the device.”
“This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this
device must accept any interference received, includinginterference that may cause undesired operation.”
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if modified or not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Index 9
Customer Service……………………………………………page 9, 11
Controller
Turning controller On…………………………………….page 6
Turning controller Off……………………………………page 7
Temperature Adjustment…………………………………page 6
Preheat…………………………………………………..page 7
Auto Off…………………………………………………page 6
FCC………………………………………………………...page 10
Issues………………………………………………………..page 8-9
Safety Warnings…………………………………………….page 2-4
Set up……………………………………………………….page 5
Warranty……………………………………………………page 9, 11
Washing Instructions……………………………………….page 7
10

customerservice
@biddefordblankets.com
ITEM: 6411
AFTER SALES SUPPORT USA 800 789
6441
Warranty Card 10
11