Eaton COOPER POWER SERIES User manual

General
Eaton meets the full requirements of IEEE Std
386™-2006 standard—Separable Insulated
Connector Systems, with its Cooper Power™
series 600 A, 35 kV insulated standoff bushing
providing a single deadbreak interface made of
high quality insulating epoxy material. It is used
in pad-mounted cabinets, underground vaults,
and other apparatus to isolate and sectionalize an
energized cable.
Temporary or permanent parking of energized
600A 35 kV deadbreak connectors that conform
to IEEE Std 386™-2006 standard is simplified with
the use of insulated standoff bushings.
The insulated standoff bushing is designed to
be installed in the parking stand mounted on a
transformer or other apparatus. A drain wire lug
is provided on the standoff bracket for attachment
of a drain wire to ensure deadfront construction.
The bushing provides a fully-shielded, submersible
connection for deadbreak operation.
Eaton's Cooper Power series 600 A, 35 kV
grounded standoff bushing is designed to be
installed in the parking stand bracket mounted on
the transformer or other apparatus.
A 2/0 AWG copper, 5-foot jacketed cable is
connected to the all-aluminum bushing for attach-
ment to system ground. The bushing provides a
fully visible ground and submersible connection
for temporary or permanent parking of 600 A
deadbreak connectors that conform to IEEE Std
386™-2006 standard.
All standoff bushing brackets have a stainless steel
eyebolt with a brass pressure foot. The bushing
body is bolted to a stainless steel base bracket
using a stainless steel bolt. Special pins ensure
firm location of the bushing on the bracket.
Installation
A clampstick tool is used to place the standoff
bushing in the parking stand on the front plate of
the apparatus. Special tools are required to thread
de-energized 600 A connectors onto the standoff
bushing. Refer to the appropriate connector
catalog section or installation instruction for further
clarification. Refer to Service Information S600-
24-1 15, 25, and 35 kV Class Insulated Standoff
Bushing Installation Instructions for complete
installation details on the insulated standoff
bushing. For installation of the grounded standoff
bushing, refer to Service Information S600-24-2
15, 25, and 35 kV Class Grounded Standoff
Bushing Installation Instructions for details.
600 A 35 kV class standoff bushings
Deadbreak Connectors
Catalog Data
CA650057EN Effective May 2015
Supersedes 600-64 December 2003
COOPER POWER
SERIES

Production tests (insulated standoff
bushing)
Tests conducted in accordance with IEEE Std 386™-2006 standard:
• ac 60 Hz 1 Minute Withstand
• 50 kV
• Minimum Corona Voltage Level
• 26 kV
Tests conducted in accordance with Eaton requirements:
• Physical Inspection
• Periodic Dissection
• Periodic Fluoroscopic Analysis
Figure 1. Grounded standoff bushing on left is made of aluminum alloy and has five feet of insulated cable. Insulated bushing on
right is molded of epoxy insulation material.
ote:N Dimensions given are for reference only.
BRACKET
Stainless steel mounting bracket has drain wire
lug for bracket and shield grounding.
COPPER CABLE
60" (1.52 mm) 2/0
Flexible, all weather 600 V
insulated copper cable
provides ease of handling and
ensures positive grounding.
STANDARD 5/8"—
11 UNC 2B
THREADS meet IEEE
Std 386™-2006
standard pecifications
for 600 A apparatus.
EPOXY INSULATION
High quality molded epoxy insulation provides
excellent electrical, thermal and mechanical reliability
for insulated standoff bushings. (Grounded standoff
bushings are made of solid wrought aluminum alloy).
BRACKET
Stainless steel
mounting bracket
has drain wire lug
for bracket and
shield grounding.
EYEBOLT
Stainless steel
eyebolt with brass
pressure foot rig-
idly secures
standoff
bushing to
parking stand.
DRAIN WIRE LUG
Provides apparatus
for attaching drain
wire.
5.6"
(142 mm)
S8
4.4"
(112 mm)
5.4"
(137 mm)
ALUMINUM
5.6"
(142 mm)
4.4"
(112 mm)
5.4"
(137 mm)
S8
Figure 2. Standoff bushing stacking dimensions.
TANK
WALL
35 kV
Grounded Insulated
S7 0.75" (19 mm) 0.75" (19 mm)
S8 5.7" (145 mm) 5.2" (132 mm)
S8 S7
Table 2. Current Ratings and Characteristics —Grounded
Standoff Bushing
Description Amperes
Short Time 25,000 A rms symmetrical for 0.17s
Table 1. Voltage Ratings and Characteristics —Insulated
Standoff Bushing
Description kV
Standard Voltage Class 35
Maximum Rating Phase-to-Ground 21.1
ac 60 Hz 1 Minute Withstand 50
dc 15 Minute Withstand 103
BIL and Full Wave Crest 150
Minimum Corona Voltage Level 26
Voltage ratings and characteristics are in accordance with IEEE Std 386™-2006 standard.
Current ratings and characteristics are in accordance with IEEE Std 386™-2006 standard.
2
Catalog Data CA650057EN
Effective May 2015
600 A 35 kV class standoff bushings
www.eaton.com/cooperpowerseries

Ordering information
To order a 35 kV Standoff Bushing Kit, refer to Table 3.
Each kit contains:
• Standoff Bushing with Bracket
• Shipping Cap (not for energized operation)
• Installation Instruction Sheet
Existing insulated or grounded bushing can be converted for
use with T-OP™ II connectors by ordering and installing the
copper alloy T-OP II** stud.
**If a T-OP II STUD (STUD-T) is installed in an existing insulated or grounded
bushing the short end of the stud must be threaded into the bushing.
**The T-OP II STUD (STUD-T) should only be used when grounding or achiev-
ing a visible break of a T-OP II termination.
Table 3. Ordering Selection Guide
Example: To order Copper Insulated Bushing with Copper Stud Loose (Shown Below)
Catalog Number would be I SB635 C S C
Standard Options
Digits: 1 2 3 4 5 6
I SB635 C S C
Digit 2 Given
Digit 1 Description
GFor Grounded Bushing***
IFor Insulated Bushing
Digit 6 Description
PStud Permanently Installed
Leave Blank Bagged Stud, Loose in Box
Leave Blank No Stud Required
Digit 4 & 5 Description
S A Aluminum Stud
S T T-OP II Stud
S C Copper Stud
Leave Blank No Stud Required
Digit 3 Description
AFor Aluminum Bushing***
CFor Copper Bushing*
* Eaton recommends when a copper standoff is designated – use only copper stud or T-OP II stud.
*** Grounded bushing available in solid wrought aluminum alloy only. Digit 3 will be “A”.
3
Catalog Data CA650057EN
Effective May 2015
600 A 35 kV class standoff bushings
www.eaton.com/cooperpowerseries

600 A 35 kV class standoff bushingsCatalog Data CA650057EN
Effective May 2015
Eaton
1000 Eaton Boulevard
Cleveland, OH 44122
United States
Eaton.com
Eaton’s Cooper Power Systems Division
2300 Badger Drive
Waukesha, WI 53188
United States
Eaton.com/cooperpowerseries
© 2015 Eaton
All Rights Reserved
Printed in USA
Publication No. CA650057EN
For Eaton's Cooper Power series standoff
bushings product information
call 1-877-277-4636 or visit:
www.eaton.com/cooperpowerseries.
Eaton, Cooper Power, and T-OP are valuable
trademarks of Eaton in the U.S. and other
countries. You are not permitted to use these
trademarks without the prior written consent
of Eaton.
IEEE Std 386™-2006 standard are trademarks
of the Institute of Electrical and Electronics
Engineers, Inc., (IEEE). This publication is not
endorsed or approved by the IEEE.