Eaton 600 A 35 kV Class Insulated Standoff Bushing User manual

600 A 35 kV class insulated protective
cap
Description
Eaton meets the full requirements of IEEE
Std 386™-2006 standard - Separable Insulated
Connector Systems, with its Cooper Power™
series 600 A, 35 kV Class insulated protective pap,
providing an insulated, fully shielded submersible
protection for energized 35 kV Class deadbreak
interfaces. The cap is required for temporary
or permanent installation on 35 kV deadbreak
bushings, junctions and other accessories having
interfaces that conform to IEEE Std 386™-2006
standard.
The cap design includes a semiconducting EPDM
insert for stress relief and high quality peroxide
cured EPDM insulation. The molded EPDM semi-
conducting shield maintains ground potential
on the cap’s surface when the drain wire is
connected to a common ground.
(Top image on left shows standard insulated
protective cap and bottom image shows U-OP™/
T-OP™ II connector insulated protective cap.)
Installation
No special tools are required. A hotstick tool is
used to place the protective cap on a de-energized
bushing. Refer to Service Information S600-63-1
600 A 15/25 and 35 kV Class Deadbreak Protective
Cap Installation Instructions for details.
Production tests
Tests are conducted in accordance with IEEE Std
386™-2006 standard.
• ac 60 Hz 1 Minute Withstand
• 50 kV
• Minimum Corona Voltage Level
• 26 kV
Tests conducted in accordance with Eaton
requirements:
• Physical Inspection
• Periodic Dissection
• Periodic Fluoroscopic Analysis
Deadbreak Connectors
Catalog Data
CA650058EN Effective May 2015
Supersedes 600-63 June 2000
COOPER POWER
SERIES

Figure 1. Insulated protective cap cutaway shows design characteristics and dimensions.
ote:N Dimensions given are for reference only.
PULLING EYE
Stainless Steel Reinforced
Pulling Eye ensures high
strength for hotstick opera-
tion.
DRAIN WIRE AND EYE
30-inch, #14 AWG Stranded Tin
Plated Copper drain wire prevents
low energy discharge from the
molded semiconducting shield.
EPDM INSULATION
High Quality Peroxide Cured EPDM Insulation
is mixed and formulated in-house for complete
control of raw rubber characteristics.
SEMICONDUCTIVE SHIELD
Molded Semiconductive EPDM Shield
meets requirements of IEEE Std 592™-
2007 standard.
5/8" – 11 UNC 2A
BRASS
THREAD
3.5"
(88 mm)
6.8"
(173 mm)
Table 1. Voltage Ratings and Characteristics
Description kV
Standard Voltage Class 35
Maximum Rating Phase-to-Ground 21.1
ac 60 Hz 1 Minute Withstand 50
dc 15 Minute Withstand 103
BIL and Full Wave Crest 150
Minimum Corona Voltage Level 26
Voltage ratings and characteristics are in accordance with IEEE Std 386™-2006 standard.
2
Catalog Data CA650058EN
Effective May 2015
600 A 35 kV class insulated protective cap
www.eaton.com/cooperpowerseries

Ordering information
To order a 35 kV Class Protective Cap Kit, refer to Table 2.
Each kit contains
• Protective Cap
• Silicone Lubricant
• Installation Instruction Sheet
Figure 2. U-OP™/T-OP™ II connector cap cutaway shows design characteristics and dimensions.
ote:N Dimensions given are for reference only.
Table 2. Protective Cap Kits
Description Catalog Number
600 A 35 kV Protective Caps
Standard Protective Cap with Drain Wire w/Permanent Stud
(See Figure 1) (Individually Bagged)
DPC635
Standard Protective Cap with Drain Wire w/Permanent Stud
(Individually Boxed)
DPC635X
Protective Cap for T-OP II and U-OP Connector Applications w/
out Stud (See Figure 2) (Individually Bagged)
DPC635UT
Protective Cap for T-OP II and U-OP Connector Applications w/
out Stud (Individually Boxed)
DPC635UTX
SEMICONDUCTIVE SHIELD
Molded Semiconductive EPDM
Shield meets requirements of
IEEE Std 592™-2007 standard.
8.66"
(220 mm)
3.25"
(83 mm)
PULLING EYE
Stainless Steel Pulling Eye
Ensures high strength for
hotstick operation.
DRAIN WIRE AND EYE
30-inch, #14 AWG Stranded Tin
Plated Copper drain wire
prevents low energy discharge
from the molded semiconducting
shield.
EPDM INSULATION
High Quality Peroxide Cured
EPDM Insulation is mixed and
formulated in-house for
complete control of raw rubber
characteristics.
5/8"-11 UNC 2A Threaded Aluminum
Insert allows cap to be installed on
bushing using either a standard 600 A
stud, the extended stud used with
T-OP™ II or the U-OP™ stud.
3
Catalog Data CA650058EN
Effective May 2015
600 A 35 kV class insulated protective cap
www.eaton.com/cooperpowerseries

600 A 35 kV class insulated protective capCatalog Data CA650058EN
Effective May 2015
Eaton
1000 Eaton Boulevard
Cleveland, OH 44122
United States
Eaton.com
Eaton’s Cooper Power Systems Division
2300 Badger Drive
Waukesha, WI 53188
United States
Eaton.com/cooperpowerseries
© 2015 Eaton
All Rights Reserved
Printed in USA
Publication No. CA650058EN
For Eaton's Cooper Power series insulated
protective cap product information
call 1-877-277-4636 or visit:
www.eaton.com/cooperpowerseries.
Eaton, Cooper Power, U-OP, and T-OP are
valuable trademarks of Eaton in the U.S. and
other countries. You are not permitted to use
these trademarks without the prior written
consent of Eaton.
IEEE Std 386™-2006 and IEEE Std 592™-2007
standards are trademarks of the Institute of
Electrical and Electronics Engineers, Inc.,
(IEEE). This publication is not endorsed or
approved by the IEEE.