Eaton Power Defense PRLSEB Series Manual

Contents
Description Page
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Instruction Leaflet IL012287EN
Installation of PRLSEB type barrier kits
PD2 Frame PD3 Frame
PD4 Frame PD5 Frame
Power
Defense™

2
IL012287EN Installation of PRLSEB type barrier kits
eaton www.eaton.com
WARNING
DO NOT ATTEMPT TO INSTALL OR PERFORM MAINTENANCE
ON EQUIPMENT WHILE IT IS ENERGIZED. DEATH, SEVERE
PERSONAL INJURY, OR SUBSTANTIAL PROPERTY DAMAGE
CAN RESULT FROM CONTACT WITH ENERGIZED EQUIPMENT.
ALWAYS VERIFY THAT NO VOLTAGE IS PRESENT BEFORE
PROCEEDING WITH THE TASK, AND ALWAYS FOLLOW
GENERALLY ACCEPTED SAFETY PROCEDURES.
EATON IS NOT LIABLE FOR THE MISAPPLICATION OR
MISINSTALLATION OF ITS PRODUCTS.
1 Introduction
This Instructional Leaflet (IL) covers the Eaton UL67 finger protection
kits listed in Table 1.
Table 1. Eaton PRLSEB type barrier kits and associated catalog
numbers.
Product Catalog Number
PD5 PRLSEBPD5
PD4 PRLSEBPD4
PD3 PRLSEBPD3
PD2 PRLSEBPD2

3
IL012287ENInstallation of PRLSEB type barrier kits
eaton www.eaton.com
2. Installation
Step
Part A
1. Installing the barrier housing
A. Align then slide the barrier housing from the front of the breaker
until the rear surfaces of the breaker and housing are even (see
Figure 1).
ote:N All barrier housing parts are designed to slide into the breaker frames
and to be held in place by friction.
Figure 1. Installation of the PD2, PD3, PD4 & PD5 barrier housings.
PD3 Frame
PD4 Frame PD5 Frame
PD2 Frame
Part A
Part A
Part A
Part A

4
IL012287EN Installation of PRLSEB type barrier kits
eaton www.eaton.com
St
Part B
ep 2. Installing the boots
Perform the following steps for each rubber boot, starting with the
center pole of the breaker.
A. Ensure the cables are maintained straight as far as possible from
the breaker. Install a cable tie around the conductors if multiple
conductors are to be inside the boot.
Figure 2. Installation of the PD2, PD3, PD4 & PD5 boots.
B. Install the large wire tie onto the end/top of the rubber boot
without fastening it. Note that the opening for the wire tie on
the rear of the boot will not be visible once the boot is installed.
C. Slide the rubber boot sub-assembly under and over the conduc-
tors. The opening should face the front of the panel.
D. Slide the boot towards the housing and align the bottom of the
boot with the housing.
E. Install the boot frame into the housing by pressing into place.
Ensure the boot is secured onto the four tabs in the housing.
PD3 Frame
PD4 Frame PD5 Frame
PD2 Frame
Part A Part A
Part B (x3)
Part B (x3)
Part B (x3)
Part B
Part A
Part A

5
IL012287ENInstallation of PRLSEB type barrier kits
eaton www.eaton.com
Step 3. Installing the front barriers - (if applicable)
A. PD3
1. Line up the barrier's circular features with the terminal
holes on the breaker.
2. Press the barrier into place.
Figure 3. Installing the PD3 front barrier.
Step 4. Completing the installation
A. Fasten the large wire tie that was previously pre-installed at
the top of the boot.
B. Install and fasten the small wire ties along the front of the
boot to close it.
C. Cut off the excess wire tie material.
Figure 4. Installation of the boot - PD2 frames.
boot - PD3 frames.Figure 5. Installation of the
Figure 6. Installation of the
Figure 7. Installation of the
boot - PD4 frames.
boot - PD5 frames.