Eaton ResistTel IP2/IP154 How to use

FHF BA9710 09/17 V8/V9
Explosion proof and weatherproof VoIP-telephones

2
Brand names are used with no guarantee that they may be freely employed. Almost all hardware and
software designations in this manual are registered trademarks or should be treated as such.
All rights reserved. No part of this manual may be reproduced in any way (print, photocopy, microfilm or
by any other means) or processed, duplicated or distributed using electronic systems without explicit
approval.
exts and illustrations have been compiled and software created with the utmost care, however errors
cannot be completely ruled out. his documentation is therefore supplied under exclusion of any liability or
warranty of suitability for specific purposes. FHF reserves the right to improve or modify this
documentation without prior notice.

Note
Please read the operating manual carefully before installing the device.
This is only a short manual. The most important operating procedures
and the mounting and installation instructions are part of this document.
For the complete configuration and operating of all features the
knowledge of the complete manual is necessary.
he complete manual is attached on the CD.
Please check the contents of the box for completeness.

Table of Contents
1 VoIP Telephone esistTel IP2 / IP152 and
Ex esistTel IP2 / IP154 .............................................. 4
1.1 Keypad ......................................................................... 4
1.2 Keypad Description ..................................................... 5
1.3 Display ......................................................................... 6
11.3.1 Default Display .................................................................. 6
21.3.1 Menu and Listing Display ................................................... 7
1.4 As-Delivered Condition ............................................... 8
11.4.1 Default Version one LAN ConnectionFehler! Textmarke nicht
definiert.
21.4.1 Version one Switch LAN Module with two LAN Connections
.................................. Fehler! Textmarke nicht definiert.
1.5 Mounting and Installing .............................................. 8
11.5.1 LAN-Connections ............................................................. 13
1.5.1.1 Default Version one LAN Connection with a Cable Gland .... 13
1.5.1.2 Version with Switch LAN Module with two LAN Connections with
Cable Glands ................................................................... 13
21.5.1 External Power Supply Connection ................................... 14
31.5.1 Relay Connection ............................................................ 14
41.5.1 Other erminals .............................................................. 15
51.5.1 Sling Holder ................ Fehler! Textmarke nicht definiert.
61.5.1 General ....................... Fehler! Textmarke nicht definiert.

3
2 Operating Manual ...................................................... 16
2.1 Operating Basics ....................................................... 16
12.1.1 Adjusting the Volume ...................................................... 16
22.1.1 Adjusting the Ringer Volume ............................................ 17
32.1.1 Do not disturb ................................................................. 17
42.1.1 Different ypes of Call Numbers ....................................... 18
52.1.1 Input of Characters and Special Characters ....................... 18
2.2 Operating Modes ....................................................... 19
12.2.1 Changeover from Handset Mode to Handset Mode with Open
Listening ......................................................................... 19
22.2.1 Changeover from Handset Mode with Open Listening to Handset
Mode .............................................................................. 19
32.2.1 Changeover from Handset Mode (with or without Open Listening)
to Hands Free Mode ........................................................ 20
42.2.1 Changeover from Handset Mode (with or without Open Listening)
to Headset Mode ............................................................. 20
52.2.1 Changeover from Hands Free Mode to Handset Mode ........ 20
62.2.1 Changeover from Hands Free Mode to Headset Mode ........ 20
72.2.1 Changeover from Headset Mode to Headset Mode with Open
Listening ......................................................................... 20
82.2.1 Changeover from Headset Mode with Open Listening to Headset
Mode .............................................................................. 20
92.2.1 Changeover from Headset Mode (with or without Open Listening)
to Handset Mode ............................................................. 20
102.2.1 Other Changeover of the Operating Mode ......................... 20
2.3 Call Functions ............................................................ 21
12.3.1 Answering Calls ............................................................... 21
22.3.1 erminating a Call ........................................................... 21
32.3.1 Making Calls .................................................................... 21
2.3.3.1 Single Dialling ................................................................. 22
2.3.3.2 Block Dialling .................................................................. 22
2.3.3.2.1 Menu Parameter Input Indirect Dialling ............................ 23
2.3.3.3 Dialling during existing Connections.................................. 24
42.3.1 Redialling ........................................................................ 24
52.3.1 Call Back ......................................................................... 25
62.3.1 Muting ............................................................................ 26
72.3.1 Making second Call .......................................................... 26
82.3.1 Switching ........................................................................ 27
92.3.1 ransferring a Call ........................................................... 27
102.3.1 ransferring a Call directly ............................................... 28
112.3.1 Initiating a Conference .................................................... 28
3 Technical Data weatherproof Telephones ................ 30
3.1 CE symbol .................................................................. 31
3.2 Use in marine and offshore segments ...................... 31

4
1VoIP Telephone esistTel IP2 / IP152 and
Ex esistTel IP2 / IP154
1.1 Keypad
Figure 1: Keypad of the VoIP-Telephone

5
1.2 Keypad Description
Sy
m
bol
Description and Key Functions
he L
oudspeaker key is used to control the hands free and listening
mode.
he Menu key is used to open the main menu or
to
save changes.
he Disconnect key is used to terminate calls or any menu.
(short)
he Enquiry key is used to enable the "Hold" and "Switch" functions.
In idle mode, the Enquiry key is used to call up the list of missed
calls. o execute the enquiry function the Enquiry key has to be
pressed short (shorter than 0.5 seconds).
(long)
he Redial key
is used to select the list of 100 phone numbers last
dialled. In the menu, the redial key confirms the current selection.
he telephone has no single Redial key. o execute the redial
function the Redial key has to be pressed long (longer than a
second).
Arrow keys are used for navigation in the menu and browsing in the
telephone directory. he volume can only be adjusted during a call.
(long)
he
asterisk
key also serves as a mute key
. During a call, a longer
press switches the microphone off or on.
...
Digit keys for entering phone numbers
.
he
asterisk
and h
ash keys
have special functions. o enter asterisk and Hash the keys have to
be pressed short (shorter than 0.5 seconds). o enter Mute (asterisk)
and Shift (hash) the keys have to be pressed long (longer than a
second). After pressing of shift the digit keys (1 – 9 and 0) become
function keys (F1 – F10). After executing a function key the shift
mode is ended.
he Clearing key is used in input mode to delete the characters left
to the cursor.
(long)
he headset key
is used to
make and to end a call in the headset
mode. he phone Resist el IP2 / IP152 has no single headset key. o
execute the headset key function the key has to be pressed long
(longer than a second) and then the loudspeaker key has to be
pressed. he headset key can be used only, if the headset is
configured to on (see manual). his makes sense only, if a headset is
connected to the phone.
Table 1: Keys and Function Elements

6
1.3 Display
he displays of the VoIP elephones Resist el IP2 / IP152 and ExResist el IP2 / IP154
have 7 lines with max. 30 characters and a state line for showing information.
1.3.1 Default Display
he name and telephone number of the current registration is displayed in the first line.
he middle lines display special information relating to the condition.
he date, time and registration status is displayed in the last line.
1 4 2 3 5
Torsten 72
06.04.10 14:40
Figure 2: Default Display (Idle State)
In the busy state state-information, date, time and the duration of the active connection
are displayed in the last line.
1 4 2 5 3
Thorsten 72
06.04.10 14:40 0:12
Figure 3: Default Display (Busy State)

7
Posit
i
on
Sy
m
bol
Description
1
Name (H.323
or SIP
ID or nickname of the PBX configuration)
2
Status line
; provides information on the current status of the
telephone by means of the following symbols.
06.04.10
Date
14:00
ime
No connection to the gatekeeper
Connection established to the gatekeeper
Connection established to the secondary gatek
eeper
Connection to the gatekeeper broken. (Both symbols are
displayed in mutual change
Open
listening
Hands free
Mode
Microphone switched off (symbol flashing)
Call diversion activated
Handset activate
Headset active
el
ephone locked
Calling number transmission locked
3
Own call number (E.164)
4
Called party
Calling party
Unknown number/name, unresolved number
Diverting party
Transferring party
Returning call
Call pending
Call on hold
5
Shift Mode
Headset configured
Audio connection of the active call is scrambled (SR P)
0:12
Duration of the active call
Table 2: Contents of the Default Display
1.3.2 Menu and Listing Display
he first six lines are used for the menu and listing display.
he last line is used for display of menu level, display name, scroll information and type
of entry.
1 2 3
display name 
Figure 4: Menu and Listing Display of the VoIP Telephone

8
Posit
i
on
Sy
m
bol
Description
1
Menu or listing level 0
<
Menu or listing level 1
Menu or listing level 2
Menu or listing level 3
Menu or listing level 4 or lower
2
Display name
3

Scrolling
up possible
Scrolling up
and down
possible

Scrolling down possible
a
A
lphanumeri
cal
input
1
Numerical input
Choice
,
next level
Table 3: Contents of the Menu and Listing Display
1.4 As-Delivered Condition
he phone is available for delivery in different versions.
•Handset with armed or spiral court
•ZB – Version (without keypad)
•Single LAN connection (1 x LAN female connector for cable mounting)
•Switch LAN module with two LAN connections (2 x LAN female connector for cable
mounting)
•Optional: relay module
Accessories (optional):
- Headset with connection cable and attachment of the bracket.
- connecting cable RJ45 - RJ45
- LAN female connector for cable mounting
- Cable glands
- Sealing plugs
he scope of the delivery includes:
- elephone
- Printed short manual
- Manual on CD
- 1 LAN resp. 2 LAN female connector for cable mounting
1.4.1 Sling Holder
he holding strength for the handset is continuously adjustable.
Loosen the screws (12) and move the stopping catches (13) (See Figure 6 on page 10).
Pushing the stopping catches together increases the holding strength whereas pulling
them apart reduces it. ighten the screws again.
1.4.2 General
he receiver is equipped with a leakage field spool for coupling of hearing aids. Users of
a hearing aid with inductive receiver may receive the signal from the receiver inset
directly.

9
1.5 Mounting and Installing
he device must be installed on a plane surface only, in vertical operating position.
Loosen the cover screws (2) (see Figure 6 to Figure 8) and detach the upper part of the
telephone (1). If the optional accessory headset or a second earpiece is being employed,
attach the bracket (10) using two screws (11) to the rear panel of the lower part of the
telephone. (With the accessories named before, the bracket and screws are in the scope
of delivery. With all accessories a cable gland is delivered.) Put four screws, having a
head diameter of 10 to 13 mm into the holes (20) and attach the lower part of the
telephone (3) to the wall or to a holder.
he telephone network cable should be passed through the cable entry (4) and
connected to terminals in accordance with the connection diagram. he attached
operating instructions for cable glands have to be considered.
Prior to assembly, check cover seal for tightness. Using the plug connector (7), plug the
ribbon cable onto the pin contact strip (8) in the upper part of the housing. Attach the
upper part of the telephone and fasten it to the lower part of the telephone with the four
cover screws (2). Upon disassembly of optional accessories, suited sealing plugs must be
used to close the resulting openings.
In this telephone connected cords may have hazardous voltages.
o ensure that no water gets into the enclosure it is essential that no gaskets are
damaged during installation. he ingress of water can cause accessible parts of the
telephone to become live.
Installation and connection must be carried out by competent personnel familiar with
electrical and network installations.
Figure 5: Drilling Diagram Wall Mounting
he diameter of the drilled hole is dependent on the screw employed (screw diameter
max. 8 mm) and the type of supporting base material (steel, wood, concrete,
plasterboard etc.) and must be chosen accordingly.
195
201

10
Figure 6: Set View
Figure 7: Inside View of Telephone upper Part

11
Figure 8: Inside View of Telephone lower Part
Figure 9: Connection Diagram with Single LAN Module
1 2 3 4 5 6 7 8 9 10 11 12 13
X
1
0
X11
X1 X2 X3 X4
X5
X6
LAN
PoE
X7
X
8
X
1
2
X
9

12
Figure 10: Connection Diagram with Switch LAN Module
Connector
D
escription
X1
empty
X2
Loudspeaker
(
left
)
X3
Heater of the Display
X4
Illumination of the
Display
X5
Display
X6
LAN Module
X7
Keypad
X8
Hookswitch
(Reed Contact)
X9
RS232 Module (optional)
X10
Amplifier Module (optional)
X11
Handset
X12
Relay Module (optional)
LAN PoE
LAN with PoE (LAN
-
Link, single LAN Module)
LAN1 PoE
LAN1 with PoE (
LAN
-
Link, Switch LAN Module)
LAN2 (PC)
LAN2 (PC
-
Link, Switch LAN Module)
1
-
13
erminals (Configuration see the following Chapters)
Table 4: Plug in Connectors and Terminals of the esistTel IP2 / IP152 with
Hardware-ID: 103
1 2 3 4 5 6 7 8 9 10 11 12 13
X
1
0
X11
X1 X2 X3 X4
X5
X7
X
8
X
1
2
X
9
X6
LAN1
PoE
LAN2

13
1.5.1 LAN-Connections
1.5.1.1 Default Version one LAN Connection with a Cable Gland
he telephone has in the default version one internal LAN-connection with a Cable Gland.
For the connection a LAN cable must be pulled through the Cable Gland. Inside the
phone the female LAN connection from AMP NE CONNEC ( E Connectivity) has to be
pressed on the cable (Refer to chapter 1.4 beginning on page 8). A female LAN cable
connector belongs to the as-delivered condition. With the inside the phone existing little
LAN connection cable, the LAN can be connected with the phone.
he LAN delivery can be available with PoE (Power over Ethernet). Alternatively the
phone can be supplied with power external.
All not used cable feed through have to be closed with sealing plugs.

Caution
You can use PoE (Power over Ethernet) or an external connection to supply the
Resist el IP2 / IP152 with power.
Don’t use both at the same time, to prevent damage to the equipment.

1.5.1.2 Version with Switch LAN Module with two LAN
Connections with Cable Glands
he telephone has in this version two internal LAN-connections with a Cable Gland. For
the connection the LAN cable must be pulled through the Cable Gland. Inside the phone
the female LAN connection from AMP NE CONNEC ( E Connectivity) has to be pressed
on the cable (Refer to chapter 1.4 beginning on page 8). A female LAN cable connector
belongs to the as-delivered condition. With the inside the phone existing little LAN
connection cable, the LAN can be connected with the phone.
he LAN1 delivery can be available with PoE (Power over Ethernet). Alternatively the
phone can be supplied with power external.
he LAN2 delivery doesn’t support PoE. Also it can’t be used to connect a phone directly,
which should be powered with PoE.
All not used cable feed through have to be closed with sealing plugs.

14
1.5.2 External Power Supply Connection
An external power supply can be adapted to the terminals 5 (+) and 6 (-). he voltage
has to be:
Without using the optional voltaic separated inputs: 15 V – 57 V DC, 12.95 W
With using the optional voltaic separated inputs: 21,5 V – 57 V DC, 12.95 W
If the external power connection will be used, you must not use PoE at the LAN
connection.
1.5.3 elay Connection
he phone can be build up with a relay module with two relays with a single changeover
switch optional.
he maximal breaking capacity of a relay is depending on the voltage:
•240 V, 6 A, AC
•24 V, 6 A, DC
•32 V, 5 A, DC
•48 V, 1 A, DC
Figure 11: Connection Diagram elay Module

Caution
Do not open the housing of the telephone while the relay contacts are energized.

K1
Relais 1 Relais 2
1 2 3 1 2 3

15
Connector
Description
K1
Cable to the main board (connection to plug in X12)
1 (relay 1)
Idle
contact relay 1
2 (relay 1)
Base
contact relay 1
3 (relay 1)
Switching contact
relay 1
1 (relay 2)
Idle
contact relay 2
2 (relay 2)
Base
contact relay 2
3 (relay 2)
Switching contact relay 2
Table 5: Plug in Connectors and Terminals of the elay Module of the
Telephone esistTel IP2 / IP152
Pay particular attention to the following points if hazardous voltages (>48V) are to be
connected to the relay outputs:
•Cable and cords must be insulated and have to be conducted below the cover.
•he circuits that the relay outputs are connected to must be of the same type; i.e.
both mains, both SELV or both NV circuits.
•It is not permissible to connect different types of circuits to these relays.
1.5.4 Other Terminals
he terminals 1 – 4 are for connecting a headset. A detailed description is enclosed in
the manual.
he terminals 7 – 13 five voltaic separated inputs are provided. All of the voltaic
separated inputs have a common null potential. Closing contacts (e. g. external push-
buttons) can be connected at the inputs. he maximum switching load for the closing
contacts is 60 V DC, 10 mA.
erminal
Description
7
Null potential of the voltaic
separated inputs
8
Null potential of the voltaic
separated inputs
9
Input 1
10
Input 2
11
Input 3
12
Input 4
13
Input 5
Table 6: Terminals of the voltaic separated Inputs

Caution
While using the voltaic separated inputs with external power supply, the input
voltage has to be 21.5 V – 57 V DC.


16
2 Operating Manual
2.1 Operating Basics
he keys below the display ( ) of the VoIP telephone serve menu navigation
and, for edit field input purposes, are assigned an additional function on top of their
actual function, as explained below.
Key assignment in menu:
The funct
i
on …
… is performed by …
scrollin
g upwards
Arrow key up
scrolling downwards
Arrow key down
one level up
without saving
Arrow key left
one level down
Arrow key right
one level up with saving
Menu key
Leave the menu complete immediately
Disconnect
key
Key assignment in edit field:
The funct
i
on …
… is performed by …
scrolling right
Arrow key right
scrolling left
Arrow key left
Delete character in front of cursor
Clearing key
Pressing and holding the numeric key, activates the character mode. Refer to chapter
2.1.5 Input of Characters and Special Characters beginning on page 18.
he initial condition means that the telephone is in the switching state hang up. his
state consists if the following conditions are fulfilled:
a) he telephone is hanged up or will be hanged off and then the key will be
pressed.
b) he hands free mode isn’t active.
c) he headset mode isn’t active.
2.1.1 Adjusting the Volume
You can adjust the volume while establishing connections as well as during calls. he
volume remains on this level after the call. he "Vol." indicator shows the current value
(see Figure 12).
You can increase the volume level by pressing the key .
You can reduce the volume level by pressing the key .

17
72
Martin 73
vol. 
06.04.10 14:40
0:22
Figure 12: Adjusting the Volume
You control the volume of the active mode.
•At the handset mode you control the volume of the speaker of the handset.
•At the listening mode you control the volume of the additional connected speaker
of the phone.
•At the hands free mode you control the volume of the speaker in hands free
mode.
•At the headset mode you control the volume of the speaker of the headset.
2.1.2 Adjusting the inger Volume
You can adjust the ringer volume while incoming calls concerning to the actual call type
(internal, external). he ringer volume remains on this level after the call. he "Vol."
indicator shows the current value (see Figure 13).
You can increase the ringer volume level by pressing the key .
You can reduce the ringer volume level by pressing the key .
Thorsten 72
Martin
73
vol. 
06.04.10 14:40 0:22
Figure 13: Adjusting the inger Volume
2.1.3 Do not disturb
You can turn off the do not disturb function of the VoIP telephone Resist el IP2 / IP152
simply by pressing a key, for example if you do not wish to be disturbed during a
meeting.
1. o activate the do not disturb function; press the key for about a second whilst in
idle mode until the display appears in Figure 14. he telephone reacts to an incoming
call depending on how this feature is configured at the time. For further details on
how to configure the do not disturb feature (see manual).

18
2. o deactivate the do not disturb function again; press the key again for about a
second until the signalling in the display is deleted. Afterwards the device will respond
to calls in the usual way again.
Torsten 72
06.01.10 14:40
Figure 14: Do not disturb
2.1.4 Different Types of Call Numbers
In addition to normal call numbers, your VoIP telephone can also dial H.323 names and
IP addresses.
Call numbers consisting of characters other than the digits 0 to 9 and the characters *
and # are considered to be H.323 names. Call numbers beginning with the character @
are always regarded as H.323 names. he @ is removed before dialling however.
2.1.5 Input of Characters and Special Characters
You can enter any Western European characters in accordance with ISO 8859-1 using
the keypad. he assignment of the characters and special characters to the keys can be
seen in able 7.
he letter mode is activated by pressing the respective key pad for an extended moment
of time. Subsequently, it is possible to switch between the letters by pressing the key
several times in short intervals or by keeping the key pressed.
key
possible characters and special characters
1
1
+ ( ) ,
-
& @ #
“
* ! $ % . / : ; < = > ?
'
[ ]
\
^ _
`{ | } ~ £ § ¿
÷
2
2 a b c A B C
ä à á â ã å æ ç Ä À Â Ã Á Å Æ Ç
3
3 d e f D E F
è é ê ë È É Ê Ë
4
4 g h i G H I
ì
í
î
ï
Ì
Í
Î
Ï
5
5 j k l J K L
6
6 m n o M N O
ö ñ ò ó ô õ ø Ñ Ò Ó Ô Õ
7
7 p q r s P Q R S
ß
8
8 t u v U V
ü ù ú û Ü Ù Ú Û
9
9 w x y z W X Y Z
ý Ý ÿ
0
0 (
space character
)
*
*
#
#
Table 7: Input of Characters and Special Characters

19
2.2 Operating Modes
he telephone allows making calls in different operating modes.
1. Handset mode
At handset mode the call will be operated with the handset.
2. Handset mode with open listening
At handset mode with open listening the call will be operated with the handset.
he hands free speaker of the phone will be connected additionally. Persons
present in the room can listen to the call.
3. Hands free mode
At hands free mode the call will be operated with the hands free microphone and
hands free speaker of the phone. All persons present in the room can take part to
the call.
If a headset is connected and configured:
4. Headset mode
At headset mode the call will be operated with the headset.
5. Headset mode with open listening
At headset mode with open listening the call will be operated with the headset.
he hands free speaker of the phone will be connected additionally. Persons
present in the room can listen to the call.
he already active operating mode will be displayed in the state line of the phone.
2.2.1 Changeover from Handset Mode to Handset Mode with
Open Listening
o change from handset mode to handset mode with open listening, you have to press
the loudspeaker key during a call.
2.2.2 Changeover from Handset Mode with Open Listening to
Handset Mode
o change from handset mode with open listening to handset mode, you have to press
the loudspeaker key during a call.

20
2.2.3 Changeover from Handset Mode (with or without Open
Listening) to Hands Free Mode
o change from handset mode (with or without open listening) to hands free mode, you
have to press the loudspeaker key and hang up the handset with pressed loudspeaker
key . Afterwards the loudspeaker key can be released.
2.2.4 Changeover from Handset Mode (with or without Open
Listening) to Headset Mode
o change from handset mode (with or without open listening) to headset mode, you
have to press the headset key (Key long (longer than a second) and then the
loudspeaker key ). Afterwards the handset can be hanged up.
2.2.5 Changeover from Hands Free Mode to Handset Mode
o change from hands free mode to handset mode, you have to lift off the handset.
2.2.6 Changeover from Hands Free Mode to Headset Mode
o change from hands free mode to headset mode, you have to press the headset key
(Key long (longer than a second) and then the loudspeaker key ).
2.2.7 Changeover from Headset Mode to Headset Mode with Open
Listening
o change from headset mode to headset mode with open listening, you have to press
the loudspeaker key during a call.
2.2.8 Changeover from Headset Mode with Open Listening to
Headset Mode
o change from headset mode with open listening to headset mode, you have to press
the loudspeaker key during a call.
2.2.9 Changeover from Headset Mode (with or without Open
Listening) to Handset Mode
o change from headset mode (with or without open listening) to handset mode, you
have to lift off the handset.
2.2.10 Other Changeover of the Operating Mode
Other changes of the operating mode can’t take place directly. hey are only possible
with one of the above listed intermediate steps indirect.