eBike KT-LCD8H User manual

KT-LCD8H eBike Display User Manual
Dear customer, please read this manual before you use KT-LCD8HDisplay. The manual will guide you use
the instrument correctly to achieve a variety of vehicle control and vehicle status displays.
Functions
and
Display
Instruments using the structure form of instrument body portion and the operation buttons are
designed separately.
1UP Button 10 Backlight and headlights
2SW Button 11 ℃
Environment temperature
3DOWN Button ℉
Environment fahrenheit
4MOTOR
W
Power display 12 Km/H Riding speed(metric)
5
ASSIST
Pas level 13
AVS
Average speed
6Km/H push power assist
MXS
MAX speed
6 THROTT
LE
Run sign 14
DST
Trip distance
7Battery capacity indicator ODO
Total distance
8VO
L
Battery voltage 15 TIM Single trip time
9The brake display TTM
Total trip time
1. Operation
1.
ON/OFF
Hold button long to turn on the power, and hold long for a second time to turn off
the power. When the motor stops driving and when the e-bike is not used for a consecutive
5 minutes, it will automatically shut down and turn off the motor power supply.
2.
Display
1
Hold button to start up and enter display .
2.1 Turn on backlight and headlights
Hold long to turn on backlight and headlights (the
controller should have headlight drive output function); hold
long again to turn off the backlight and headlights.
2.2 Assist ratio gear (ASSIST) switch
Hold or shortly to switch 1-5 file gear. Gear 1 is for
the minimum power, gear 5 is for the highest power. Eachstartup
will automatically restore the gear shutdown last time (the user can
set randomly). Gear 0 is without booster function.
2.3 6Km/H assist promotion function
Hold and flashes, the vehicle drives at the speed not
more than 6Km /h. Release button, the function is invalid.
2.4
Display
and
delete
of
single
data
After power on for 5 seconds, hold and at the
same time, single trip riding time (TM) and single trip distance
(DST) flash, hold button shortly, the content of both is
cleared. If failed holding the button within 5 seconds, it will
automatically return the display interface after 5 seconds, original content is preserved.
3.
Display
2
Hold button shortly in display 1 to enter display 2.
In the riding mode after 5 seconds, display 2 automatically
returns to display 1, and the original motor power (MOTOR W)
display is replaced with motor operating temperature display
(MOTOR ℃) display (the internal motor should be equipped
with the temperature sensor and the output of temperature detection signal).
4.
Display
3
Hold button shortly in display 2 to enter display 3.
In the riding condition, five seconds later, a single maximum
speed (MXS) display automatically returns to the real riding
speed (Km/H).
5.
In
display
3,
hold
button
shortly
(SW),and
the
display
will
re-enter
display
1.
6.
Hold
button
to
turn
off
the
display
and
the
power
supply
of
controller.

7.
Automatically
prompt
interface
Error Code Display Error Code Definition
Motor position sensor fault! Motor Hall Signal Abnormality
THROTTLE fault! Throttle Abnormality
Motor or controller short circuit fault! Motor or controller has short circuit
Abnormality
The fault is excluded and the fault code display interface is automatically exited.
General Project Setting
1.
Set
maximum
riding
speed
After power on for 5 seconds, hold and at the same
time, maximum riding speed Km/H and MXS flash,hold or
shortly to set the maximum riding speed (default 25Km/H). Hold
button shortly and go to the next parameter settings.
2.
Wheel
diameter
setting
The wheel diameter will be set after finishing setting the
maximum riding speed, wheel diameter specifications flashes.
Hold or shortly to set the specifications of wheel
diameter. Select the range
6,8,10,12,14,16,18,20,22,24,26,700c,28and 29 inches.Hold
button shortly and go to the next parameter settings.
2. Set the metric units
The metric units will be set after finishing setting wheel
diameter, Km/H and Km flash. Hold or shortly and
select the three metric units of speed, mileage, and ambient
temperature in synchronization.
Display Metric
Riding speed Km/H
Total distance Km
Environment temperature ℃Temperature
4. Km/H and Km stop flash after metric unit setting is completed. Hold button shortly again
to re-enter the maximum riding speed setting interface; or hold button long to exit from
setting environment of routine projects and save the setting values, returning to display 1.
5.
Exit
from
routine
project
setting
All three routine project settings can exit from the setting environment and return to the
display
if hold button long after each setting is completed, meanwhile the setting values are saved.
Under each setting interface, if the button failed holding for more than 1 minute, it will
automatically return to display 1, and the setting value is invalid.
Outline Drawings and Dimensions
1.Dimensions of main instrument body 2.Mounting dimensions of double brackets
3.Dimensions of button box 4.Wiring diagram
www.greenbikekit.com