6" Chipper Specs
26" [66cm] DIAMETER DISC
Dynamically balanced solid steel disc rotates counter clockwise at
1750 RPM. New cantilever design which greatly reduces wrapping and
a side strike anvil. 26" [66cm] dia. X 1" [2.5cm] thick rotor shaft with
1.75" [4.4cm] bearings.
ENGINE WITH ELECTRIC START
• CH6670H (76624) Honda 670cc OHV twin cylinder gas engine.
• CH611DH (76628) Kubota 1.1 Liter 3 cylinder liquid cooled
engine, Tier II diesel.
• CH6993H (76635) Briggs and Stratton 993cc V-Twin gas engine
TRIPLE-BANDED BELT DRIVE FOR BETTER TRANSFER OF POWER
FLUID CAPACITY
Hydraulic oil tank, 4 gal. 15 liters] capacity. 18 gal. [68 liters] fuel tank
HYDRAULIC SYSTEM
4 position valve with reverse at both ends, positive neutral, with ow
control. Single 15" [38.1cm] diameter feed roller 13" [33cm] width
with 1.25" [3.2cm] bearing. Roller contains 10 knife blades. Feed roll-
er can be reversed without starting the disc. Smart Feed System with
instant reverse and “Try Again" feed system. Automatically will re-try
feeding limbs. Hydraulic feed roller with hydraulic jack. Easing mainte-
nance and safety. Load-sensing Two-stage pump. Feed rate 0-125 feet
per minute [0-46 meters/min]. Average 100 FPM [30 meters/min].
with innite speed settings, dedicated neutral and full reverse, pump
output. 6.6 gal [25 liter] per minute and 4HP with maximum pressure
and maximum ow. Feed system operates under 1750 PSI [119atm],
3 gal. [11.4 liter] tank capacity.
MANUAL BELT ENGAGEMENT LEVER
FEED OPENING
6.5" X 13.5" [16.5cm x 91.4cm]
90° FEED ANGLE
Quicker chipping because you are cutting through less wood.
FEED CHUTE
6.5" X 13.5" [16.5cm x 91.4cm], tray 28.31" [71.9cm] off the ground.
Feed table is 38" [96.5cm] long. Infeed hopper opening: height 33.8"
[86cm], width 59" [150cm] Drop-down feed tray with locking safety
pin.
HINGED ENGINE COMPARTMENT
Fully enclosed engine compartment for noise abatement. Steel
18-gallon [68 liters] gasoline/diesel fuel tank. .25" [6.35mm] steel
disc housing. Hydraulic hose protection.
HEAVY-DUTY CONSTRUCTION
.375" [9.5mm] thick steel face plate on the disc housing;
.25" [6.35mm] thick steel on the wrap around with welded construc-
tion. Frame is 2" x 2" [5cm x 5cm], .25" [6.35mm] wall thickness tub-
ing. Table is 7 gauge [4.55mm] steel. Tongue is 2" x 2" [5cm x 5cm]
with .25" [6.35mm] wall thickness.
DISCHARGE CHUTE
360º rotation, 6.7" [17cm] square discharge chute. 18 positions for
locking discharge chute in desired position. Deector cap with screw-
type adjustment at operator level.
COMPACT 60" [152cm] WIDE TRAILER.
Excellent for tight roads, streets, storage, and maneuverability. Tor-
sion axle suspension, 15" [38.1cm] tires, heavy-duty fenders. 2" ball
coupler. Spare tire option available
ADJUSTABLE JACK (Towable models only)
Roller wheel with 850 lb. [372kg] Rating. Adjustable jack allows one
person to easily maneuver the chipper around and hook up to a
vehicle.
LIGHTING (12-VOLT SYSTEM)
Light package, including rubber mounted taillights and license plate
holder. Lighted hour meter and fuel gauge standard.
ALERT SYSTEMS (ADJUSTABLE):
Factory set at 15 hours for blades, 100 hours for oil changes.
Blade hour maintenance code alerts time to check the blades for
sharpening. Service alert reminds owner of time to change the oil.
DIMENSIONS:
• Length 142" [361cm]. • Width 60" [153cm]
• Height 93" [236cm.
Weight
• 670cc Honda chipper – 2100 lbs. [954kg]
• 1.1 Liter Diesel Kubota chipper – 2305 lbs. [1045kg]
• 993cc Briggs & Stratton chipper - 2140 lbs. [972kg]
SAFETY
• Safety chains standard
• Meets all applicable ISO safety standards.
Find a dealer near you!
Call us at 800.247.7335 or
Log onto www.BearCatProducts.com
237 12th St. NW • P.O. Box 849, West Fargo, ND 58078
Fax: 701.282.9522
