EchoMaster Pro PBS-MW01 User manual

OPERATION GUIDE
PBS-MW01
BLIND SPOT DETECTION SYSTEM

1. WARNING ......................................... Page 1
2. SYSTEM CONTENTS ................................. Page 2
3. INTRODUCTION .................................... Page 3
4. LANE CHANGE ALERT ................................ Page 3
5. REAR CROSS TRAFFIC ALERT .......................... Page 4
6. DOOR OPEN WARNING .............................. Page 4
7. SYSTEM SPECIFICATIONS ............................ Page 5
8. OPERATION ....................................... Page 6
9. ERROR DIAGNOSTICS ............................... Page 7
10. TROUBLESHOOTING ............................... Page 8
CONTENTS

1| BLIND SPOT DETECTION SYSTEM BLIND SPOT DETECTION SYSTEM | 2
1. WARNING
1.THE BLIND SPOT DETECTION SYSTEM DOES NOT REPLACEANY FUNCTIONS DRIVERS SHALLORDINARILY
PERFORM IN DRIVING A MOTOR VEHICLE, NOR DOES IT DECREASE THE NEED FOR DRIVERS TO STAY VIG-
ILANT AND ALERT IN ALL DRIVING CONDITIONS,TO OBEY ALLTHE SAFE DRIVING STANDARDS, PRACTICES,
TRAFFIC RULES AND REGULATIONS.
2. ECHOMASTER DOES NOT GUARANTEE 100% ACCURACY INTHE DETECTION OF VEHICLES OR PEDESTRI-
ANS, AND THEREFORE DOES NOT GUARANTEE THE PERFORMANCE OF ANY RELATED AUDIO OR VISUAL
WARNING SIGNALS. FURTHERMORE, ROAD, WEATHER AND OTHER CONDITIONS MAY ADVERSELY AFFECT
THE VEHICLE’S BLIND SPOT DETECTION SYSTEM RECOGNITION AND RESPONSE CAPABILITIES.
3. CAREFULLY READ THIS OPERATION GUIDE AND ITS IMPORTANT SAFETY INSTRUCTIONS AND WARN-
INGS PRIOR TO INSTALLING OR USING THE BSD SYSTEM.
4. IT IS RECOMMENDED THAT THE INSTALLATION BE CARRIED OUT BY QUALIFIED PERSONNEL.
Do not pull the connectors with excessive
force.
Do not pull the harness with excessive
force.
1. WARNING 1
3. INTRODUCTION 3
5. OPERATION 4
4. SYSTEM SPECIFICATIONS 3
7. TROUBLESHOOTING 6
6. ERROR DIAGNOSTICS 5
2. SYSTEM CONTENTS 2

BLIND SPOT DETECTION SYSTEM | 2
2. SYSTEM CONTENTS
No. ITEM Qty PICTURE
3
4
5
6
7
8
9
10
21
Left Blind Spot Sensor
11
Right Blind Spot Sensor
Control Unit 1
Right Indicator 1
Buzzer 1
Power Button
1
1
Harness Set
Left Indicator 1
OBD II Cable 1
1
Manual Set /Accessories
1

3| BLIND SPOT DETECTION SYSTEM BLIND SPOT DETECTION SYSTEM | 4
3. INTRODUCTION
The Blind Spot Detection System is designed to aid in detecting vehicles that may have
entered the vehicle’s blind spot zone, which is represented by the vehicles in the diagram
below.The detection area is on both sides of your vehicle, extending rearward from the vehicle
to approximately 30 feet beyond the bumper. The system is designed to alert you of vehicles,
which will not allow for a safe lane change.
30 ft
30 ft
30 ft
30 ft
4. LANE CHANGE ALERT
Lane Change Alert is activated when the turn signals are used to make a lane change and
when the vehicle speed exceeds 15 MPH.The warning zone of the system covers left and right
adjacent lanes with an estimated impact in less than 2 seconds. An audible tone will be heard
and the warning indicator lamp with the corresponding turn signal will ash when a vehicle is
within the warning zone or if there is a vehicle detected approaching at high speeds resulting
in an impact of less than 2 seconds during the lane change.

BLIND SPOT DETECTION SYSTEM | 4
5. REAR CROSS TRAFFIC ALERT
The Rear Cross Trafc Alert (RCTA) is activated when the vehicle is placed in ‘reverse’. An
audible tone will be heard and the corresponding warning indicator lamp will ash when a
pedestrian or vehicle is detected approaching and resulting in an impact of approximately 2
seconds. The system is capable of monitoring the rear cross trafc zones up to a 60 ft range.
6. DOOR OPEN WARNING
DOW is activated when under two conditions; when the engine is on and the hazard
indicators are activated, and ve minutes after stopping the engine. An audible tone will be
heard and the warning indicator lamp with the corresponding turn signal will ash when an
object or vehicle is within the warning zone or if there is a vehicle detected approaching at
high speeds resulting in an impact of less than 2 seconds
30 ft
30 ft
30 ft
30 ft

5| BLIND SPOT DETECTION SYSTEM BLIND SPOT DETECTION SYSTEM | 6
7. SYSTEM SPECIFICATIONS
SOUND
Operating Temperature1
3
5
Environmental Protection Level
Current Consumption
-40ºC~ +85ºC
Storage Temperature
2-40ºC ~ +90ºC
Input Voltage Range
412V (9V – 16V)
Radar：IP67
500mA@12V ; 6. 0W
7Accuracy of Alarm
Alarm Level
6Level I ：LED On (Constant)
Level II：LED Flash+Buzzer On
Specifications
8ISO 17387/IS0 16750
Vehicle: >99%
No. ITEM SPECIFICATIONS
Radiation Regulations9
11 Warning Light
FCC / NCC / VSCC
Buzzer
10 75dB
5V Drive, A Pillar

BLIND SPOT DETECTION SYSTEM | 6
8. OPERATION
Indicator
Left Side Blind Spot Indicator
Right Side Blind Spot Indicator
POWER button
System Power
1. The system will automatically activate when the ignition is turned on.The warning
indicator lamps illuminate for 3 seconds during startup.
2. The system may be deactivated by pressing and holding the POWER button for
3 seconds, the indicator lamps will blink twice to conrm.
3. The system may be reactivated by pressing and holding the POWER button for
3 seconds, the indicator lamps will illuminate for 3 seconds to conrm.
System Activation
1. Start vehicle.
2. Indicator lamps will illuminate for 3 seconds to conrm activation and run
self-diagnostics.
3. If there are errors, the system will ash the indicator lamps and sound
tones to indicate the problems. Please use the TROUBLESHOOTING section for
more help.
4. The Blind Spot Detection System will turn on when you start the engine and begin
driving forward above approximately 15mph.
Blind Spot Indicator Lamps
1. The left indicator will illuminate when a vehicle is in your left blind spot while
driving. This indicator will ash and an audible tone will sound when your left turn
signal is activated while there is a vehicle in the left blind spot.
2. The right indicator will illuminate when a vehicle is in your right blind spot
while driving. This indicator will ash and an audible tone will sound when your
right turn signal is activated while there is a vehicle in the right blind spot.
1
2
1 2
1 2
1 2
3
3
1 2
1 2
Controller HMI CAN TX Failed
Radar System Error - Master
Sleep Mode
System Initialization
Do Re Mi
Do Re Mi
1 second beep, stop .5 second & 1 second beep
3 second beep
STATUS SOUND

7| BLIND SPOT DETECTION SYSTEM BLIND SPOT DETECTION SYSTEM | 8
9. ERROR DIAGNOSTICS
It is possible that the Blind Spot Detection System will trigger an alert even though there is
no vehicle in the blind spot zone. The Blind Spot Detection System can detect objects such as:
construction barrels, guard rails, lamp posts, etc. Occasional false alerts are normal.
Controller HMI CAN TX Failed
Radar System Error - Master
Sleep Mode
System Initialization
Do Re Mi
Do Re Mi
1 second beep, stop .5 second & 1 second beep
3 second beep
STATUS SOUND

BLIND SPOT DETECTION SYSTEM | 8
10. TROUBLESHOOTING
ISSUE POSSIBLE CAUSE POSSIBLE SOLUTION
The system does not
respond after starting
the engine
The indicator does not
light up
The buzzer makes no
sound
The power switch
does not work
[ Do Re Mi ] alarm Radar disconnection or
no OBD connection
IGN lead connected
to constant power
Did not enter sleep
mode after 5 minutes of
IGN off
Power On
Self-test
System
Operation
Functions
Incorrect connection or
control unit failure
Damaged indicator
Damaged buzzer
Contact your dealer
Contact your dealer
Contact your dealer
Abnormal power supply,
wiring, or radar, please
contact your dealer
Disconnected indicator
Disconnected buzzer
Damaged power switch
Disconnected power
switch
Confirm that the IGN,
wiring, fuse, and
controller are connected
No Level 1 BSD alert
No Level 2 BSD alert
No RCTA alert
Vehicle speed is less
than 12 mph
Bad connection from
OBDII
Turn signal leads not
connected
Reverse lead not
connected
Normal operation.
The vehicle is not compatible.
Please contact the dealer
Confirm turn signal leads are
connected
Confirm that the reverse lead
is connected
SYMPTOM
Verify connection
Verify connection, press and
hold the switch for 2 seconds
Change the IGN to a switched
power source connection
location
Press the RESET button on
the control unit after starting
the engine. Check the system
again after the reboot is
completed.
Verify connection

15500 Lightwave Dr, Suite 202, Clearwater, FL 33760 • 866-931-8021 • www.echomaster.com • [email protected]
REV: 0320