Eco-Systems ECO-1109 Manual

866.463.2611 •www.ecosystemsdisplays.com
Setups
Order ###### - ECO-1109 - 10’x10’ Sustainable Exhibit
Plan View
10’
10’

866.463.2611 •www.ecosystemsdisplays.com
General Info
7A
General Setup Instructions
•The setup instructions are created specifically for your configuration.
•Setup instructions are laid out sequentially in levels, including exploded
views and a logical series of steps for assembly. We encourage you to study
the instructions before attempting to assemble your exhibit.
Hex Tool for Assembling Exhibit Extrusion Lock Connectors
Numbering Instructions for Setups/Packing Inline Connection between Extrusions Baseplate Connection for Vertical Extrusions
Cleaning and Packing
•Use non-abrasive cleaners when cleaning extrusions or ECO Glass inserts.
•Use mild cleaners and soft materials such as cotton to clean all laminates.
•Keep exhibit components away form extreme heat and long exposure to
sun light. This will prevent warping and fading.
•Retain all packing material for ease of re-packing. This protects the exhibit
components and keeps each part organized.
Disassembling
•When disassembling exhibit, tighten all setscrews to prevent loss of hardware
in the shipping process.

866.463.2611 •www.ecosystemsdisplays.com
General Info
124 5
SEG Graphic Install
1
2
3
4
Graphic is installed corners first. This allows a proportional fit around the
perimeter of the extrusion.
Locate channels along the edge of the extrusions.
Fold over graphic (hiding threads) and tuck silicon edge and fabric
into corners.
After corners are complete, slide in the rest of the graphic into channel.
(From edges to center)
3
5Graphic is installed. Stand back and be amazed!
Place ECO panel together with a vertical offset, slide down to lock
connector in place.
Panel Corner Connectors are installed just like ECO panels. Remove by
off-setting top lock clips horizontally followed by separating vertically.
2
1
ECO Panel Install 12

866.463.2611 •www.ecosystemsdisplays.com
Step 1
2
22
1
2
3 4 5
6
7
810 9 333
Shelf
Shelf
Plan View: Top Level
Plan View: Bottom Level
Item
2
3
Qty.
1
1
Description
95”h Q914 Vertical Extrusion
95”h Q914 Vertical Extrusion w/ TSP3
Steps:
1) Assemble lower Eco Panels [1through 10] together
in numerical order; attach to vertical extrusions [2,3]
as shown.
2) Assemble upper Eco Panels [1through 10] together
in numerical order & connect to vertical extrusions.
3) Place internal Shelf on shelf pins.
2
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
10
10
9
9
3
Item
1
2
3
4
5
6
7
8
9
10
Qty.
1
1
1
1
1
1
1
1
1
1
Description
47.5”h Square Cap Connector
19”w x 47.5”h Eco Panel
47.5”h 90° Connector
30”w x 47.5”h Eco Panel
47.5”h 90° Connector
19”w x 47.5”h Eco Panel w/ Door
47.5”h Square Cap Connector
47.5”h Square Cap Connector
25.791”w x 47.5”h Eco Panel
47.5”h Square Cap Connector
Item
1
2
3
4
5
6
7
8
9
10
Qty.
1
1
1
1
1
1
1
1
1
1
Description
47.5”h Square Cap Connector
19”w x 47.5”h Eco Panel
47.5”h 90° Connector
30”w x 47.5”h Eco Panel w/ S10
47.5”h 90° Connector
19”w x 47.5”h Eco Panel w/ Door
47.5”h Square Cap Connector
47.5”h Square Cap Connector
25.791”w x 47.5”h Eco Panel
47.5”h Square Cap Connector
1
TSP3
Extrusion
Profile
2
3
45
6
7
8
10
9
1
S10
Extrusion
Profile

866.463.2611 •www.ecosystemsdisplays.com
Step 2
Steps:
1) Install Base Plate [1] to bottom of
vertical extrusion [4] using bolt.
2) Connect horizontals [5,5A,5B]
between verticals [3,4].
3) Apply SEG Graphics as shown.
Item
1
4
5/5A
5B
Qty.
1
1
1/1
1
Description
Base Plate
95”h Q914 Vertical Extrusion w/ TSP3
78”w Z45 Horizontal Extrusion w/ TSP3
78”w Q914 Horizontal Extrusion 4
3
5
5A
5B
1
Mitre
Cut
TSP3 Corner
Connection
Slide TSP3 extrusion
into groove of vertical
& tighten set screw
to secure in place.
SEG Graphic Installation
Corner A
Corner D
Corner B
Corner C
It is important to first insert
graphic into each alternate
corner then to the sides of
the frame. If this is not done,
graphic will not fit into the
frame correctly.
Step 1
Insert corner A. Turn edge of
graphic so silicon welt is
perpendicular to face of
graphic. Insert narrow side
of welt with fabric to outside
into the channel. Repeat for
other side of this corner.
Step 2
Repeat Step 1 for opposite
corner C, then insert corner
B, followed by corner D, to
complete the installation of
the corners.
Graphic Removal
To remove the graphic from
the frame, locate the fabric
pull tab. Gently pull up on
the tab to remove the fabric.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work toward the center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
TSP3
Extrusion
Profile

866.463.2611 •www.ecosystemsdisplays.com
Step 3
When assembled
Steps:
1) Assembled Aero frame parts together in numerical order
as shown.
2) Apply pillowcase graphic to assembled frame.
1
2
3
4
5
79
10
11
13 15
16
17
19
20
18
14
12
8
6
Connections are made by holding the button
down and sliding the red tube into opposing
tube until the connection is made. To disassemble
push button and pull or twist extrusions apart.
Push-Button
Push-Button
66
6
6
Numbered Label
Using Your Setup Instructions
The Aero Overhead Sign Setup Instructions are created specically for your conguration. They include an
exploded view of the frame which is sequentially numbered. We encourage you to study the instructions
before attempting to assemble your exhibit.
Connections are kept very simple: no tools. Everything assembles with push-button
connectors and pre-connected horizontal sections.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only non-abrasive cleaners.
2) Retain all packing material. It will make re-packing much easier and will reduce the likelihood
of shipping damage.

866.463.2611 •www.ecosystemsdisplays.com
Step 4
Completed Assembly
Steps:
1) Install Aero Header Frame to backwall as shown. See Keyhole Attachment detail.
2) Connect light(s) to horizontal [5A]. See Light Attachment detail.
3) Attach Standoff Graphics to front cabinet panels using standoff barrels & caps.
See Standoff Graphic Attachment detail.
*Keyhole Attachment
Insert bolts of aero frame into keyhole
slote in groove of vertical extrusion,
slide aero frame down to secure.
Graphic
Cap
Standoff
Barrel
Attach standoff barrels to
backwall panel and secure
in place. Secure graphic to
standoffs using screw caps.
Standoff Graphic Attachment
Panel
*
*
Lock Clip into Groove of
Horizontal Extrusion, then
slide Light onto Clip.
Light Attachment
Slide light into light
receiving hardware
Lock into
groove of
horizontal
*
*