Eco-Systems Backlit Hybrid S ECO-1087 User manual

866.463.2611 •www.ecosystemsdisplays.com
Setups
Order #XXXXX - ECO-1087 - 10’x10’ Backlit Sustainable Exhibit
Plan View
10’
10’

866.463.2611 •www.ecosystemsdisplays.com
General Info
7A
General Setup Instructions
•The setup instructions are created specifically for your configuration.
•Setup instructions are laid out sequentially in levels, including exploded
views and a logical series of steps for assembly. We encourage you to study
the instructions before attempting to assemble your exhibit.
Hex Tool for Assembling Exhibit Extrusion Lock Connectors
Numbering Instructions for Setups/Packing Inline Connection between Extrusions Baseplate Connection for Vertical Extrusions
Cleaning and Packing
•Use non-abrasive cleaners when cleaning extrusions or ECO Glass inserts.
•Use mild cleaners and soft materials such as cotton to clean all laminates.
•Keep exhibit components away form extreme heat and long exposure to
sun light. This will prevent warping and fading.
•Retain all packing material for ease of re-packing. This protects the exhibit
components and keeps each part organized.
Disassembling
•When disassembling exhibit, tighten all setscrews to prevent loss of hardware
in the shipping process.

866.463.2611 •www.ecosystemsdisplays.com
General Info
124 5
SEG Graphic Install
1
2
3
4
Graphic is installed corners first. This allows a proportional fit around the
perimeter of the extrusion.
Locate channels along the edge of the extrusions.
Fold over graphic (hiding threads) and tuck silicon edge and fabric
into corners.
After corners are complete, slide in the rest of the graphic into channel.
(From edges to center)
3
5Graphic is installed. Stand back and be amazed!
Place ECO panel together with a vertical offset, slide down to lock
connector in place.
Panel Corner Connectors are installed just like ECO panels. Remove by
off-setting top lock clips horizontally followed by separating vertically.
2
1
ECO Panel Install 12

866.463.2611 •www.ecosystemsdisplays.com
Case 1
Graphics
Setup Hardware
Top View of Each Level
Level 1 Level 2
2B
4A 5A
3B
3A
5B 4B
2A

866.463.2611 •www.ecosystemsdisplays.com
Case 2
Top View of Each Level
Level 1 Level 2 Level 3
Base Plates
(qty 2)
6A 6B
Graphic
Headers
Wings
(qty 4)
Shelf

866.463.2611 •www.ecosystemsdisplays.com
Step 1
bolt
set
screw
V4
When Assembled
Item
1
2A/2B
3A/3B
4A/4B
5A/5B
6A/6B
Qty.
2
1/1
1/1
1/1
1/1
1/1
Description
Baseplate
48” CEI110 Horizontal Extrusion
48” CEI110 Horizontal Extrusion
40.25” CEI110 Vertical Extrusion
40.25” CEI110 Vertical Extrusion
46.8125” S91 Vertical Extrusion
Steps:
1) Attach Baseplate [1] to horizontal [2A] using
bolt & wing nut.
2) Attach Baseplate [1] to vertical [6A] using bolt.
3) Connect horizontals [2A-3A, 2B-3B] and
verticals [4A-5A, 4B-5B, 6A-6B] together.
See CEI-110 Frames Assembly in the General
Information Pages.
4) Connect Horizontal and Vertical assemblies together.
See CEI-110 Frames Assembly in the General
Information Pages.
5) Connect vertical assembly [6A-6B] to
vertical assembly [4B-5B], using V4 connectors
& bolts as shown.
6) Connect lighting Power Cords and attach
Transformers. See Light to Light Attachment &
Light to Transformer Attachment details.
7) Attach SEG to assembled frame.
See SEG Graphic Install in the
General Information Pages.
++
+
-
-
-
to power
Lights
Male
Female
Transformer
Light to Light Attachment
Light to Tranformer Attachment
1
2A
Transformer
Transformer
Transformer
Transformer
3A
SEG
4A
4B 6A
6B
5B
5A
2B
Power Break 3B
1
Power Break
to power
to power
to power
to power
Slide V4 Connectors
into groove of vertical
extrusion. Tighten
Set Screws to secure
in place. Use bolts to
attach vertical to
V4 connector.

866.463.2611 •www.ecosystemsdisplays.com
Step 2
When assembled
bolts
S12
V4
connectors
monitor
mount
V31
connector
Item
--
--
Qty.
1
1
Description
8.5”h S12 Vertical Extrusion
8.5”h V31 Connector
6A
6B
Graphic Headers
Steps:
1) Connect Graphic Headers to assembled backwall
with A10 Clamps. See A10 Clamp detail.
2) Connect Shelf to Vertical [6A/6B].
See Shelf Attachment detail.
3) Install Monitor Mount to vertical [6A/6B] using
S12 extrusion & V31 connector.
See Monitor Mount Attachment detail.
2) Tighten Set Screw to
secure A10 to Vertical.
1) Slide A10 connector
into groove of Vertical.
A10 Clamp
Wing
4) Tighten knob to secure
Wing in place.
3) Insert Wing into A10.
1
2
3
4
Shelf Attachment
Insert Lock into groove of Vertical
then tighten Set Screw.
Lock Set Screw
Back of Shelf
Set Screw will face
outward for ease
of assembly
**
*
*
Wing
Wing
*
*
Wing
Wing
*
*
Monitor Mount Attachment
Keep S12 & V31 permanently attached to vertical
extrusion. DO NOT DISASSEMBLE.
*
Connect S12 vertical extrusion to backwall vertical
using V31 connector. Tighten set screws to secure
connection.
Slide V4 connectors into groove of S12 & tighten
set screws. Then use bolts to attach Monitor Mount
to V4 connectors.