Eco-Systems ECO-37C Manual

Locked layer contains
placeholder marks.
866.463.2611 • www.ecosystemsdisplays.com
A7
General Setup Instructions
•The setup instructions are created specifically for your configuration.
•Setup instructions are laid out sequentially in levels, including exploded
views and a logical series of steps for assembly. We encourage you to study
the instructions before attempting to assemble your exhibit.
Hex Tool & Phillips Screwdriver are included for Assembling Exhibit Extrusion Lock Connectors
Numbering Instructions for Setups/Packing Inline Connection between Extrusions Baseplate Connection for Vertical Extrusions
Cleaning and Packing
•Use non-abrasive cleaners when cleaning extrusions or ECO Glass inserts.
•Use mild cleaners and soft materials such as cotton to clean all laminates.
•Keep exhibit components away form extreme heat and long exposure to
sun light. This will prevent warping and fading.
•Retain all packing material for ease of re-packing. This protects the exhibit
components and keeps each part organized.
Disassembling
•When disassembling exhibit, tighten all setscrews to prevent loss of hardware
in the shipping process.
General Info

Locked layer contains
placeholder marks.
866.463.2611 • www.ecosystemsdisplays.com
Graphic is installed corners first. This allows a proportional fit around the
perimeter of the extrusion.
Locate channels along the edge of the extrusions.
Fold over graphic (hiding threads) and tuck silicon edge and fabric
into corners.
After corners are complete, slide in the rest of the graphic into channel.
(From edges to center)
Graphic is installed. Stand back and be amazed!
ECO Panel Install
SEG Graphic Install
Place ECO panel together with a vertical offset, slide down to lock
connector in place.
Panel Corner Connectors are installed just like ECO panels. Remove by
off-setting top lock clips horizontally followed by separating vertically.
General Info

Locked layer contains
placeholder marks.
866.463.2611 • www.ecosystemsdisplays.com
Locked layer contains
placeholder marks.
Setup Hardware
Top View of Each Level
Level 1
(Bottom level) (Top level)
Level 2
ECO-37C
Counter Leg
ECO-37C
Counter Top
Case 1

Locked layer contains
placeholder marks.
866.463.2611 • www.ecosystemsdisplays.com
Locked layer contains
placeholder marks.
Top View of Each Level
Level 1
(Bottom level)
Level 2 Level 3 Level 4 Level 5
(Top level)
Level 6
3,7 2 4 6 8
Graphic
ECO-37C
Pedestal Top
1,5
ECO-37C
Shelf
Shelf
Supports
Case 2

Locked layer contains
placeholder marks.
866.463.2611 • www.ecosystemsdisplays.com
Step 1
Locked layer contains
placeholder marks.
TOP VIEW
Steps:
Refer to the ECO Panel Assembly Instructions general information page.
1) Assemble ECO panels & connectors [1] through [8] together in numerical order.
2) Affix Shelf Supports to inside of panel assembly; place internal Shelf.
3) Place pedestal top onto assembled base.
4) Attach Graphic to front of pedestal assembly. See Graphic Attachment detail.
5) Connect Leg to Counter Top. See Counter Top w/ Threaded Stud Attachment detail.
2) Connect Counter Top to assembled pedestal.
See Counter Top w/ Standoff Barrel Attachment detail.
Item
1
2
3
4
5
6
7
8
Qty.
1
1
1
1
1
1
1
1
Description
15.888”w x 35”h ECO Panel
35”h 90° Connector
21.388”w x 35”h ECO Panel w/ Door
35”h 90° Connector
15.888”w x 35”h ECO Panel
35”h 90° Connector
21.388”w x 35”h ECO Panel
35”h 90° Connector
When assembled
Counter Top w/ Standoff Attachment
*
Attach standoff barrels to
nut serts in top of Pedestal.
Then connect Counter Top
to standoff barrels using
wing nuts.
Use access hole under
Counter Top when
attaching wing nuts.
wing
nut
standoff
barrel
nut
sert
Counter Top
Pedestal
Counter Top w/ Threaded Stud
Attachment
*
Insert threaded stud into
nut sert on top of Counter
Leg. Twist to secure in place.
Place holes on bottom of
Counter Top over threaded
stud & secure using wing
nuts.
Use access hole under
Counter Top when
attaching wing nuts.
wing
nut
threaded
stud
nut
sert
Counter Top
Counter Leg
**
*
*
Counter Leg
Pedestal
Assembly
Counter Top
Pedestal Top
Shelf
1
2
2
1
8
3 4
5
67
Door
34
5
6
7
8
Grap
h
i
c
Graphic Attachment
*
Graphic Screw
Cap
Stand-Off
Barrel
Attach stand-off barrel to panel using screw
from inside pedestal assembly. Then attach
graphic to stand-off using screw caps.
Panel
Screw
Mouse hole
faces back of
assembly
Holes for wire
management
power cord
**
**
ECO-37C
Note: Phillips screwdriver
required for installation