Eco-Systems ECO-1010 User manual

866.463.2611 •www.ecosystemsdisplays.com
Setups
Order #XXXXX - ECO-1010 - 10’x10’ Sustainable Hybrid Display
Plan View
10’
10’

866.463.2611 •www.ecosystemsdisplays.com
General Info
7A
General Setup Instructions
•The setup instructions are created specifically for your configuration.
•Setup instructions are laid out sequentially in levels, including exploded
views and a logical series of steps for assembly. We encourage you to study
the instructions before attempting to assemble your exhibit.
Hex Tool for Assembling Exhibit Extrusion Lock Connectors
Numbering Instructions for Setups/Packing Inline Connection between Extrusions Baseplate Connection for Vertical Extrusions
Cleaning and Packing
•Use non-abrasive cleaners when cleaning extrusions or ECO Glass inserts.
•Use mild cleaners and soft materials such as cotton to clean all laminates.
•Keep exhibit components away form extreme heat and long exposure to
sun light. This will prevent warping and fading.
•Retain all packing material for ease of re-packing. This protects the exhibit
components and keeps each part organized.
Disassembling
•When disassembling exhibit, tighten all setscrews to prevent loss of hardware
in the shipping process.

866.463.2611 •www.ecosystemsdisplays.com
General Info
124 5
SEG Graphic Install
1
2
3
4
Graphic is installed corners first. This allows a proportional fit around the
perimeter of the extrusion.
Locate channels along the edge of the extrusions.
Fold over graphic (hiding threads) and tuck silicon edge and fabric
into corners.
After corners are complete, slide in the rest of the graphic into channel.
(From edges to center)
3
5Graphic is installed. Stand back and be amazed!
Place ECO panel together with a vertical offset, slide down to lock
connector in place.
Panel Corner Connectors are installed just like ECO panels. Remove by
off-setting top lock clips horizontally followed by separating vertically.
2
1
ECO Panel Install 12

866.463.2611 •www.ecosystemsdisplays.com
Step 1
Keyholes in vertical
extrusion should face toward
front of booth for proper
attachment of Aero frames.
Keyholes in vertical
extrusion should face toward
front of booth for proper
attachment of Aero frames.
Item
1
2
3
4
6
7/7A
8/8A
Qty.
1
1
1
1
1
2/2
1/1
Description
Base Plates
87.75”h S44 Vertical Extrusion w/ PR63
88”h S44 Vertical Extrusion w/ PR63
88”h S44 Vertical Extrusion w/ PR63
87.75”h S44 Vertical Extrusion w/ PR63
24”w Z45 Horizontal Extrusion
58”w Z45 Horizontal Extrusion
Steps:
1) Connect Base Plates [1] to bottom of
verticals [2,6] using bolts.
2) Connect horizontals [7,7A,8,8A]
between verticals as shown.
3) Attach fabric graphics to back of display
using Velcro.
When assembled
Velcro: Back Edge
Velcro: Back Edge
Velcro: Back Edge
Velcro: Back Edge
Velcro: Back
Top Edge
Velcro: Back
Top Edge
Velcro: Back Top Edge
Velcro: Back Bottom Edge
Velcro: Back
Bottom Edge Velcro: Back
Bottom Edge
1
2
7
8
7A
7A
7
8A
3
46
Attach graphics
to velcro on back of
assembled frame

866.463.2611 •www.ecosystemsdisplays.com
Step 2
**
*
**
Steps:
1) Assemble lower Eco Panels & Connectors
[1] through [8] together in numerical order.
2) Assemble upper panels & connectors [1-2-3]
to lower panels as shown.
3) Attach cabinet assemblies to backwall verticals,
as shown. See Backwall Connection detail.
4) Affix shelf supports inside cabinet assemblies;
place internal Shelves.
5) Place Counter Tops to top of cabinets.
6) Install Monitor Mount to upper Eco Panel.
See Monitor Mount Attachment detail.
Item
1
2
3
4
5
6
7
8
Qty.
2
2
2
2
2
2
2
2
Description
40”h 90° Connector
20”w x 40”h Eco Panel
40”h 90° Connector
15”w x 40”h Eco Panel
40”h 120° Connector
21.57”w x 40”h curved Eco Panel w/ Door
40”h 120° Connector
15”w x 40”h Eco Panel
1
2
3
2
2
2
51”h Square Cap Connector
20”w x 51”h Eco Panel
51”h Square Cap Connector
123
4
5
6
78
123
123
4
5
6
78
123Screw cap
V4
Connector
set
screw
Slide V4 connectors
into groove of vertical
extrusion. Tighten set
screws to secure.
Attach Eco Panel to
V4 connector using
screw caps.
Backwall Connection
*
Slide V4 connectors
into groove of vertical
extrusion. Tighten set
screws to secure.
Use bolts to secure
Monitor Mount to
V4 connectors.
Monitor Mount Attachment
**
V4
Connector
bolts
Monitor
Mount
Eco Panel
Eco Panel
set
screw
set
screw
Shelf
shelf support
shelf support
shelf support
shelf support
Counter Top
TOP VIEW
1
7
8
2 3
4
5
6
When assembled

866.463.2611 •www.ecosystemsdisplays.com
Step 3
Connections are made by holding the button
down and sliding the red tube into opposing
tube until the connection is made. To disassemble
push button and pull or twist extrusions apart.
Push-Button
Push-Button
66
6
6
Numbered Label
Using Your Setup Instructions
The Aero Overhead Sign Setup Instructions are created specically for your conguration. They include an
exploded view of the frame which is sequentially numbered. We encourage you to study the instructions
before attempting to assemble your exhibit.
Connections are kept very simple: no tools. Everything assembles with push-button
connectors and pre-connected horizontal sections.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only non-abrasive cleaners.
2) Retain all packing material. It will make re-packing much easier and will reduce the likelihood
of shipping damage.
Left Aero Frame
1
2
3
45
7
8
6
Right Aero Frame
1
2
3
45
7
8
6
Steps:
1) Assemble Aero Frame parts
in numerical order as shown.
2) Apply pillowcase graphic.
When assembled

866.463.2611 •www.ecosystemsdisplays.com
Step 4
*
*
Steps:
1) Attach left & right Aero frames to backwall verticals.
See Aero Frame-to-Vertical Attachment detail.
Bolt Attached
to Aero Frame
Bolt
V20 Connector
Insert bolts of aero frame into keyhole
slote in groove of vertical extrusion,
slide aero frame down to secure.
Aero Frame-to-Vertical Attachment
*
Keyhole
Left Aero Frame
*
*
Right Aero Frame
When assembled

866.463.2611 •www.ecosystemsdisplays.com
Step 5
Connections are made by holding the button
down and sliding the red tube into opposing
tube until the connection is made. To disassemble
push button and pull or twist extrusions apart.
Push-Button
Push-Button
66
6
6
Numbered Label
Using Your Setup Instructions
The Aero Overhead Sign Setup Instructions are created specically for your conguration. They include an
exploded view of the frame which is sequentially numbered. We encourage you to study the instructions
before attempting to assemble your exhibit.
Connections are kept very simple: no tools. Everything assembles with push-button
connectors and pre-connected horizontal sections.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only non-abrasive cleaners.
2) Retain all packing material. It will make re-packing much easier and will reduce the likelihood
of shipping damage.
When assembled
Steps:
1) Assemble Aero Frame parts together as shown.
NOTE: For the 10’x10’ booth configuration, attach
connections [4to 6] & [9to 11] together as shown.
2) Apply pillowcase graphic.
FOR 10’x10’ BOOTH CONFIGURATION:
1
2
3
4-6
7
8
11-9
12

866.463.2611 •www.ecosystemsdisplays.com
Step 6
**
Steps:
1) Attach left & right Aero frames to backwall verticals
using clips. See Aero Clip Connection detail.
2) Clip Lights onto Aero frame where desired.
See Light Attachment detail.
Light Attachment
Attach lights to
Aero frame &
tighten in place.
*
Insert Clip into top of
LT Square Cap Connector.
LT square cap
connector
Aero
clip
Aero Frame
LT Panel
Backwall
*Aero Clip Connection
Aero Clip BACK VIEW
When assembled
**