Eco-Systems ECO-1067 User manual

866.463.2611 •www.ecosystemsdisplays.com
Setups
Order #XXXXX - ECO-1067
When assembled

866.463.2611 •www.ecosystemsdisplays.com
General Info
7A
General Setup Instructions
•The setup instructions are created specifically for your configuration.
•Setup instructions are laid out sequentially in levels, including exploded
views and a logical series of steps for assembly. We encourage you to study
the instructions before attempting to assemble your exhibit.
Hex Tool for Assembling Exhibit Extrusion Lock Connectors
Numbering Instructions for Setups/Packing Inline Connection between Extrusions Baseplate and Connection for Extrusions
Cleaning and Packing
•Use non-abrasive cleaners when cleaning extrusions or ECO Glass inserts.
•Use mild cleaners and soft materials such as cotton to clean all laminates.
•Keep exhibit components away form extreme heat and long exposure to
sun light. This will prevent warping and fading.
•Retain all packing material for ease of re-packing. This protects the exhibit
components and keeps each part organized.
Disassembling
•When disassembling exhibit, tighten all setscrews to prevent loss of hardware
in the shipping process.

866.463.2611 •www.ecosystemsdisplays.com
General Info
124 5
SEG Graphic Install
1
2
3
4
Graphic is installed corners first. This allows a proportional fit around the
perimeter of the extrusion.
Locate channels along the edge of the extrusions.
Fold over graphic (hiding threads) and tuck silicon edge and fabric
into corners.
After corners are complete, slide in the rest of the graphic into channel.
(From edges to center)
3
5
5Graphic is installed. Stand back and be amazed!
Place ECO panel together with a vertical offset, slide down to lock
connector in place.
Panel Corner Connectors are installed just like ECO panels. Remove by
off-setting top lock clips horizontally followed by separating vertically.
2
1
ECO Panel Install 12

866.463.2611 •www.ecosystemsdisplays.com
General Info
SETUP INSTRUCTIONS

866.463.2611 •www.ecosystemsdisplays.com
Case 1
Order #xxxxx -
Setup le can be found online at
www.ecosystemdisplays.com

866.463.2611 •www.ecosystemsdisplays.com
Step 1
1
2
2A
5
5A
6
6A
7
7A
3
3A
4
4A
1
1
When assembled
Item
1
2/2A
3/3A
4/4A
5/5A
6/6A
7/7A
Qty.
3
1/1
1/1
1/1
1/1
1/1
1/1
Description
Base Plate
43”h Vertical Extrusion
43”h Vertical Extrusion
43”h Vertical Extrusion
35”w Horizontal Extrusion
35”w Horizontal Extrusion
24”w Horizontal Extrusion
Steps:
1) Connect verticals to base plates with bolts.
2) Attach upper verticals to lower verticals as shown in S44 Connector detail.
3) Connect lower horizontals together as shown in S44 Connector detail.
4) Connect upper horizontals together as shown in S44 Connector detail.
5) Connect lower and upper horizontals between verticals.
6) Attach graphics to backwall where indicated.
Velcro: Top
Edge
Velcro: Bottom
Edge
Velcro: Bottom
Edge
Velcro: Top
Edge
Velcro: Inside
Edge
Velcro: Inside
Edge
Screws
Connector
Piece
S44 Connector
Silde extrusion over
connector and rest on
lower vertical;
secure with screws.
**To prevent product loss,
Keep all screws attached
to connector piece after
disassembling

866.463.2611 •www.ecosystemsdisplays.com
Step 2
8
10A
9A 10A
10
9
8A
When assembled
Graphic
Infill
Infill
Graphic
Graphic
Item
8/8A
9/9A
10/10A
Qty.
1/1
1/1
1/1
Description
24.5”h Vertical Extrusion
24”w Horizontal Extrusion
12”w Horizontal Extrusion
Steps:
1) Attach graphic with stand off caps as shown in detail.
2) Connect horizontals [9] & [9A] between verticals [8] & [8A].
3) Connect lower horizontals [10] between verticals.
4) Attach infills between verticals on top of lower horizontal [10].
5) Attach upper horizontal [10A].
10
*
*
*
*
*
*
*
Graphic
Cap
V20
Slide connector with stud into
groove of extrusion and
twist to secure in place. Attach
graphic with cap as shown.
Graphic to Post Attachment

866.463.2611 •www.ecosystemsdisplays.com
Step 3
Door
Counter
Shelf
Shelf
Shelf
Wing
Wing
Wing
Wing
When assembled
Steps:
1) Attach wings to backwall using A10 Clamp Detail.
2) Connect door to counter assembly Door Attachment detail.
3) Place counter on top of assembly.
4) Attach monitor mount as shown in Monitor Mount Attachment detail.
5) Attach shelves to vertical where indicated.
Monitor Mount
Attachment
Slide connectors into
groove of extrusion;
tighten setscrew to secure.
Then attach wall plate
to connectors using
supplied bolts.
Setscrew
*
Door
Hinge
Hinge
Door Attachment
Slide pin into
hinge attached
to vertical.
Slide door
hinge over pin.
Tighten set screw to
secure A10 to extrusion.
A10 Clamp Detail
Tighten knob to secure
header/wing in place.
*

866.463.2611 •www.ecosystemsdisplays.com
Step 4
Connections are made by holding the button
down and sliding the red tube into opposing
tube until the connection is made. To disassemble
push button and pull or twist extrusions apart.
Push-Button
Push-Button
66
6
6
Numbered Label
Using Your Setup Instructions
The Aero Overhead Sign Setup Instructions are created specically for your conguration. They include an
exploded view of the frame which is sequentially numbered. We encourage you to study the instructions
before attempting to assemble your exhibit.
Connections are kept very simple: no tools. Everything assembles with push-button
connectors and pre-connected horizontal sections.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only non-abrasive cleaners.
2) Retain all packing material. It will make re-packing much easier and will reduce the likelihood
of shipping damage.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
When assembled

866.463.2611 •www.ecosystemsdisplays.com
Step 5
When assembled
Steps:
1) Use canopy attachment to attach canopy to upper verticals.
2) Attach light as shown in detial.
3) Attach graphic to velcro where indicated.
Velcro: Inside
Edges