Eco-Systems Eco-104T User manual

866.463.2611 •www.ecosystemsdisplays.com
Setups
Order #45374 - Eco-104T Table Top

866.463.2611 •www.ecosystemsdisplays.com
General Info
7A
General Setup Instructions
•The setup instructions are created specifically for your configuration.
•Setup instructions are laid out sequentially in levels, including exploded
views and a logical series of steps for assembly. We encourage you to study
the instructions before attempting to assemble your exhibit.
Hex Tool for Assembling Exhibit Extrusion Lock Connectors
Numbering Instructions for Setups/Packing Inline Connection between Extrusions Baseplate and Connection for Extrusions
Cleaning and Packing
•Use non-abrasive cleaners when cleaning extrusions or ECO Glass inserts.
•Use mild cleaners and soft materials such as cotton to clean all laminates.
•Keep exhibit components away form extreme heat and long exposure to
sun light. This will prevent warping and fading.
•Retain all packing material for ease of re-packing. This protects the exhibit
components and keeps each part organized.
Disassembling
•When disassembling exhibit, tighten all setscrews to prevent loss of hardware
in the shipping process.

866.463.2611 •www.ecosystemsdisplays.com
General Info
124 5
SEG Graphic Install
1
2
3
4
Graphic is installed corners first. This allows a proportional fit around the
perimeter of the extrusion.
Locate channels along the edge of the extrusions.
Fold over graphic (hiding threads) and tuck silicon edge and fabric
into corners.
After corners are complete, slide in the rest of the graphic into channel.
(From edges to center)
3
5
5Graphic is installed. Stand back and be amazed!
Place ECO panel together with a vertical offset, slide down to lock
connector in place.
Panel Corner Connectors are installed just like ECO panels. Remove by
off-setting top lock clips horizontally followed by separating vertically.
2
1
ECO Panel Install 12

866.463.2611 •www.ecosystemsdisplays.com
Step 1
Back View
2
3
1
1
4
4A
5
5A When assembled
Item
1
2
3
4/4A
5/5A
Qty.
2
1
1
1/1
1/1
Description
Base Plate
Vertical Extrusion
Vertical Extrusion
Horizontal Extrusion
Horizontal Extrusion
Steps:
1) Attach base plates to verticals.
2) Connect horizontals together as shown.
3) Connect lower horizontals between verticals.
4) Connect upper horizontals between verticals.
5) Attach graphics to velcro where indicated.
Velcro: Top
Edge
Velcro: Bottom
Edge

866.463.2611 •www.ecosystemsdisplays.com
Step 2
1
2
3
4
5
6
78
9
11 12
10
Steps:
1) Connect in numberical order as shown.
2) Apply pillow case graphic.
When assembled
Connections are made by holding the button
down and sliding the red tube into opposing
tube until the connection is made. To disassemble
push button and pull or twist extrusions apart.
Push-Button
Push-Button
66
6
6
Numbered Label
Using Your Setup Instructions
The Aero Overhead Sign Setup Instructions are created specically for your conguration. They include an
exploded view of the frame which is sequentially numbered. We encourage you to study the instructions
before attempting to assemble your exhibit.
Connections are kept very simple: no tools. Everything assembles with push-button
connectors and pre-connected horizontal sections.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only non-abrasive cleaners.
2) Retain all packing material. It will make re-packing much easier and will reduce the likelihood
of shipping damage.

866.463.2611 •www.ecosystemsdisplays.com
Step 3
Header
Aero Assembly
Steps:
1) Attach header to A10 clamps as shown in detail.
2) Slide aero frame into grove of vertical.
When desired location
is found, tighten
set screw to secure.
Slide connector on back
of A10 clamp into groove
of extrusion.
Example of A10 Clamp Attachment
Tighten knob to secure
shelf/wing in place.

866.463.2611 •www.ecosystemsdisplays.com
Case 1
Order #45374 -
Setup le can be found online at
www.ecosystemdisplays.com