ECR 4 Kids ELR-0453-B User manual

Use a Phillips Screwdriver
Use the
Hex Tool
Use a Phillips
Screwdriver
C
D
E
F G
H
I
J
K
LM
Top Panel (1)
Left & Right Side Panels (1/1)
Parts List
A
B
BEFORE ASSEMBLING, MAKE SURE YOU HAVE ALL THE PARTS
Upper Dividers (4) Upper Back Panel (5)
Lower Back Panel (1)
Lower Dividers (4)
Cam Posts & Cam Locks (16/16)
K1
L1
L2
K2
A1 A2
Upper Shelf (1)
Lower Shelf (1)
Bottom Shelf (1)
Batch ID Sticker
located on underside
Hanger Hooks (10)Hanger Hook Posts
& Screws (12/12)
Hex Screw (32)
5 Section Coat Locker w/ Bench
Model# ELR-0453-B
San Diego, CA 92110 USA
www.ecr4kids.com
Adult Assembly Required.
Two adults recommended.
- Contains small parts, sharp points and edges.
- Do not stand, sit, kneel, climb, lean or pull on unit for support.
- Never leave children unattended.
- Do not place unit near high heat or moisture.
- Adult supervision recommended.
WARNING:
TOOLS INCLUDED
Hex Tool (1) TOOLS NEEDED
Phillips Screwdriver
Children climbing on furniture
can lead to death or serious
injury due to tipping. Secure
unit to wall using appropriate
hardware.

3Connect Lower Dividers to Lower Shelf
Insert Upper Shelf onto Upper Dividers
4
1
Install Upper Dividers onto Lower Shelf
2
Install Lower Dividers onto Bottom Shelf
Batch ID Sticker
See Next Page
Install the four Lower Dividers (H) to the Bottom Shelf (E) with eight Hex Screws (J)
using the Hex Tool.
Install the four Upper Dividers (F) to the Lower Shelf (D) as shown,
with eight Hex Screws (J) using the Hex Tool.
Install eight Cam Posts (K1) into the threaded plastic inserts on the
underside of Lower Shelf (D) with a Phillips screwdriver.
Reminder: Do not overtighten, as the plastic threads can be stripped.
Place two Cam Locks (K2) into the recessed holes on each Lower Dividers (H), with the
arrow facing the closest edge.
Attach the Lower Dividers (H) onto the Cam Posts on the underside of the Lower Shelf (D),
turn the Cam Locks clockwise with a Phillips screwdriver to lock the Lower Dividers (H) onto
the posts.
Align the slits on Upper Shelf (C) with the slits on Upper Dividers (F) as shown,
and slide together until seated.
Two Adults Recommended:Carefully rotate the unit upright.
C
a
r
e
f
u
l
l
y
R
o
t
a
t
e
U
p
r
i
g
h
t

5Insert Upper Back Panels
Connect the Top Panel to Upper Dividers
6
7Insert the Left Upper Back Panel
Install the Left Side Panel
8
See Next Page
Install eight Cam Posts (K1) into
the threaded plastic inserts on
the underside of Top Panel (B)
with a Phillips screwdriver.
Reminder: Do not overtighten,
as the plastic threads can be
stripped.
Insert the Top Panel (B) Cam
Posts into the holes on the top
edge of the Upper Dividers (F).
Turn the Cam Locks clockwise
with a Phillips screwdriver to lock
the Upper Dividers (F) onto the
posts.
Install the Left Side Panel (A1) to the Top Panel (B), Upper Shelf (C), Lower Shelf (D)
and Bottom Shelf (E) with eight Hex Screws (J) using the Hex Tool.
Slide three Upper Back Panels (G)
into the grooves on the Upper
Dividers (F) as shown, until fully
seated into the groove on the
topside of the Lower Shelf (D).
Tip: If the Back Panels do not slide
in easily, wiggle the panels while
pushing into place.
Place two Cam Locks (K2) into the
recessed holes on each Upper
Dividers (F), with the arrow facing
the closest edge.
Slide an Upper Back Panel (G) into the grooves on the Top Panel (B) and Lower Shelf (D)as
shown, until fully seated into the groove on the side of the Upper Divider (F).
Tip: If the Back Panels do not slide in easily,
wiggle the panels while pushing into place.

9Insert the Remaining Back Panels
Install the Right Side Panel
10
11 Install the Coat Hooks
See Next Page
Install the Right Side Panel (A2) to the Top Panel (B), Upper Shelf (C), Lower Shelf (D)
and Bottom Shelf (E) with eight Hex Screws (J) using the Hex Tool.
Slide the remaining Upper Back Panel (G) into the grooves on the Top Panel (B) and Lower
Shelf (D)as shown, until fully seated into the groove on the side of the Upper Divider (F).
Slide the Lower Back Panel (I)
into the grooves on the Lower
Shelf (D)and Bottom Shelf (E)
as shown, until fully seated into
the groove on the inside of Left
Side Panel (A1).
Install two Hanger Hooks (N) to each locker section by threading the Hanger Hook Posts &
Screws (L1/L2) together from both sides of each vertical divider (A1/A2/F).
Tip: If the Back Panels
do not slide in easily,
wiggle the panels while
pushing into place.

Record the manufacture date here.
Information is located on the Batch ID
sticker and on the shipping carton.
Save this sheet in an accessible place.
Model Number: ELR-0453-B
Factory Code: EP
Manufacture Date:
Batch ID Number:
(Located on Part E)
©2015 ECR4KIDS, LP Version: ELR-0453-B_EP_2015.03.18
Care and Cleaning
Clean unit with a damp cloth or sponge
using warm water and mild soap. Wipe dry.
Do not place near heat, moisture or
vaporizer which may cause panels to warp
and peel.
Check for loose or worn parts periodically
and tighten or replace as necessary.
We appreciate your purchase of the 5 Section Coat Locker with Bench.
ECR4KIDS has made every effort to supply a quality product that with proper
use and care, will provide many years of trouble-free use.
Warranty: Visit our website for product specific warranty information at:
www.ecr4kids.com
If you experience any difficulties with this product, please email us at
[email protected] or call toll-free at (855) ECR-4KIDS
(Monday - Friday, 7:00am - 4:00pm Pacific Standard Time)
Please do not return to place of purchase as ECR4KIDS will
replace defective part(s) and/or product.
To prevent a tip-over tragedy:
Buy and install low-cost anchoring devices that can prevent TVs,
dressers, bookcases and other furniture from tipping. For more
information please visit www.ecr4kids.com/resources