ECR 4 Kids 20 Section Storage Cabinet ELR-0426-A User manual

B
C
D
E
F
Use the Hex Tool.
Batch ID
located underneath.
Middle Shelf (1)
Top Panel (1)
Left & Right
Side Panels (1/1)
Parts List
A
BEFORE ASSEMBLING, MAKE SURE YOU HAVE ALL THE PARTS
Phillips Screws & Casters (16/4)
Cam Posts & Cam Locks (16/16)
Bottom Shelf (1)
Dividers (8)
Thin Shelves (10)
Back Panels (2)
Hex Screws (28)
Use a Phillips Screwdriver.
Use a Phillips Screwdriver.
G
H
I
J
Children climbing on furniture can lead to
death or serious injury due to tipping.
Secure unit to wall using appropriate
hardware.
J1 J2
I1 I2
A1 A2
TOOLS INCLUDED
Hex Tool (1)
TOOLS NEEDED
Phillips Screwdriver
20 Section
Storage Cabinet
Model# ELR-0426-A
Adult Assembly Required.
Two adults recommended.
- Contains small parts, sharp points and edges.
- Do not stand, sit, kneel, climb, lean or pull on
unit for support.
- Never leave children unattended.
- Do not place unit near high heat or moisture.
- Adult supervision recommended.
WARNING:
San Diego, CA 92110 USA
www.ecr4kids.com

2Install Upper Dividers to Middle Shelf
1Install the Casters onto Bottom Shelf
3Connect Top Panel to Upper Dividers
5Connect Middle Shelf to Lower Dividers
4Install Lower Dividers to Bottom Shelf
Install the Upper Dividers (E) onto the Middle Shelf (C) with eight Hex Screws (H) using the
Hex Tool. Note: The grooves on the Middle Shelf are away from the ground.
Install the Lower Dividers (E) on to the Bottom Shelf (D) with eight Hex Screws (H) using the
Hex Tool. Note: The groove on the Bottom Shelf is away from the ground.
Install eight Cam Posts (I1) into the threaded plastic inserts on the underside of Top Panel (B)
with a Phillips screwdriver. Reminder: Do not overtighten, as the plastic threads can be stripped.
Note: The groove on the Top Panel is away from the ground.
Insert the Top Panel (B)
Cam Posts into the holes on
the top edge of the Upper
Dividers (E). Turn the Cam
Locks clockwise with a
Phillips screwdriver to lock
the Upper Dividers (E) onto
the posts.
Install eight Cam Posts (I1) into the threaded plastic inserts on the underside of Middle Shelf (C)
with a Phillips screwdriver.
Reminder: Do not overtighten, as the plastic threads can be stripped.
Insert the Middle Shelf (C) Cam Posts into the holes on the top edge of the Lower Dividers (E).
Turn the Cam Locks clockwise with a Phillips screwdriver to lock the Lower Dividers (E) onto the
posts.
See Next Page
Place two Cam Locks (I2)
into the recessed holes on
each Upper Divider (E),
with the arrow facing the
closest edge.
Batch ID Sticker
Install the four Casters (J2) into the pre-drilled holes on the underside of the Bottom Shelf (D),
with four Phillips Screws (J1) per caster, using a Phillips screwdriver.

6
7Insert Back Panels
Install Right Side Panel Install Left Side Panel
8
9Insert Thin Shelves
C
a
r
e
f
u
l
l
y
R
o
t
a
t
e
U
p
r
i
g
h
t
See Next Page
Slide the Back Panels (F) into the grooves on to the Top Panel (B), Middle Shelf (C) and
Bottom Shelf (D) as shown, until fully seated into the groove on the inside of the Right Side
Panel (A2).
Tip: If the Back Panels does not slide in easily, wiggle the panels while pushing into place.
Install the Right Side Panel (A2) on to the Top Panel (B), Middle Shelf (C) and Bottom Shelf (D)
with six Hex Screws (H) using the Hex Tool.
Install the Left Side Panel (A1) on to the Top Panel (B), Middle Shelf (C) and Bottom Shelf (D)
with six Hex Screws (H) using the Hex Tool.
Two Adults Recommended:
Carefully rotate unit upright.
Slide the Thin Shelves (G) into the grooves on the sides of Upper & Lower Dividers (E) and
insides of the Side Panels (A1, A2) as shown, until fully seated against the Back Panels.
Tip: If the Shelves do not slide in easily,
wiggle them while pushing into place.

©2015 ECR4KIDS, LP Version: ELR-0426-A_EP_2015.03.17
Care and Cleaning
Clean wood with a damp cloth or sponge
using warm water and mild soap. Wipe dry.
Do not place near heat, moisture or
vaporizer which may cause wood to warp
and peel.
Check for loose or worn parts periodically
and tighten or replace as necessary.
Record the manufacture date here.
Information is located on the Batch ID
sticker and on the shipping carton.
Save this sheet in an accessible place.
Model Number: ELR-0426-A
Factory Code: EP
Manufacture Date:
Batch ID Number:
(Located on Part D)
We appreciate your purchase of the 20 Section Storage Cabinet.
ECR4KIDS has made every effort to supply a quality product that with proper
use and care, will provide many years of trouble-free use.
Warranty: Visit our website for product specific warranty information at:
www.ecr4kids.com
If you experience any difficulties with this product, please email us at
[email protected] or call toll-free at (855) ECR-4KIDS
(Monday - Friday, 7:00am - 4:00pm Pacific Standard Time)
Please do not return to place of purchase as ECR4KIDS will
replace defective part(s) and/or product.
We appreciate your purchase of the 20 Section Storage Cabinet.
ECR4KIDS has made every effort to supply a quality product that with proper
use and care, will provide many years of trouble-free use.
Warranty: Visit our website for product specific warranty information at:
www.ecr4kids.com
If you experience any difficulties with this product, please email us at
[email protected] or call toll-free at (855) ECR-4KIDS
(Monday - Friday, 7:00am - 4:00pm Pacific Standard Time)
Please do not return to place of purchase as ECR4KIDS will
replace defective part(s) and/or product.
To prevent a tip-over tragedy:
Buy and install low-cost anchoring devices that can prevent TVs,
dressers, bookcases and other furniture from tipping. For more
information please visit www.ecr4kids.com/resources