ECR 4 Kids ELR-17102-A User manual

A
Left/Right Side Panels (2)
Must be drilled to mount to wall
per individual installation application
Parts List
Top Panel (1)
Upper Rail (1)
Lower Rail (1)
Bottom Panel (1)
Back Panels (3)
Frame Wall Mount (1)
Wall Mount (1)
F
H Connector (2)
L
BI
J
C
K
D
M
E
N O
G
H
Shelves
ELR-17100 = 2pcs
ELR-17101 = 3pcs
ELR-17102 = 4pcs
Short Hex Screws (6)
Cam Posts & Cam Locks (2/2)
M1 M2
A1 A2
Small Cam Posts
(4 per shelf)
Phillips Screws (6)
BEFORE ASSEMBLING, MAKE SURE YOU HAVE ALL THE PARTS
Long Hex Screws (10)
Batch ID Sticker
located on underside
Use the
Hex Tool Use the Hex Tool
Use a Phillips
Screwdriver
Use a Phillips
Screwdriver
Use a Phillips
Screwdriver
36”, 48” & 60” Book Case
ELR-17102-A ELR-17101-A ELR-17100-A
Adult Assembly Required.
Two adults recommended.
- Contains small parts, sharp points and edges.
- Do not stand, sit, kneel, climb, lean or pull on
unit for support.
- Never leave children unattended.
- Do not place unit near high heat or moisture.
- Adult supervision recommended.
WARNING:
TOOLS INCLUDED
Hex Tool (1)
TOOLS NEEDED
Phillips Screwdriver
Drill Driver
+ Drill Bits
San Diego, CA 92110 USA
www.ecr4kids.com
Children climbing on furniture
can lead to death or serious
injury due to tipping. Secure
unit to wall using appropriate
hardware.

See Next Page
C
a
r
e
f
u
l
l
y
R
o
t
a
t
e
U
p
1Attach Upper Rail to Top Panel
2Install Lower Rail to Bottom Panel
3Install the Left Side Panel
4
5
Insert the Back Panels
Insert the Frame Wall Mount
Place two Cam Locks (M2) into the
recessed holes on the backside of
Upper Rail (G), with the arrow facing
the closest edge.
Attach the Upper Rail onto the Cam
Posts on the underside of the Top
Panel (B) as shown, turn the Cam
Locks clockwise with a Phillips
screwdriver to lock the Upper Rail
onto the posts.
Install two Cam Posts (M1) into the threaded plastic inserts on the underside of Top Panel (B)
with a Phillips screwdriver. Reminder: Do not overtighten as the plastic threads can be stripped.
Install the Lower Rail (H) to the
Bottom Panel (C) with two Long
Hex Screws (L) using the Hex Tool.
Note: The two wide channels on the
Lower Rail should face toward the
backside of the unit.
Install the Left Side Panel (A1) to the
Top Panel (B) and Bottom Panel (C)
with four Long Hex Screws (L) using
the Hex tool.
Note: The pre-installed wooden
dowels in the Upper & Lower Rails fit
into the corresponding holes that are
not drilled thru the side panels.
Two Adults Recommended: Rotate
the unit onto the Left Side Panel (A1).
Insert the pre-installed wooden dowels on the Frame Wall Mount (E) into the holes on the
Left Side Panel (A1) first, then into the Top Panel (B).
Slide one Back Panel (J) into the
grooves on the Top Panel (B) &
Bottom Panel (C) as shown, until
fully seated into the groove on the
inside of the Left Side Panel (A1).
Note: The small holes on the
Back Panels should be placed on
the bottom of the unit.
Insert an H Connector (I) onto the
edge of the first Back Panel, this
will nest into the wide channels on
the Upper & Lower Rails. Repeat
for the remaining Back Panels.
Tip: If the Back Panels do not
slide in easily, wiggle the panels
while pushing into place.
Batch ID Sticker
Small holes
go at bottom

8Attach the Shelves
9Install the Wall Mount
6Attach the Right Side Panel
7Install the Back Panel Screws
Consult a professional Handyman, Carpenter or Maintenance person to install the wall mount.
They can determine suitable wall mounting hardware, available from your local home improvement
store, for your particular application.
The Wall Mount (F) should be secured in a minimum of two locations, preferably into wall studs.
Install the Right Side Panel (A2)
to the Top Panel (B) and Bottom
Panel (C) with four Long Hex
Screws (L) using the Hex tool.
Note: The pre-installed wooden
dowels in the Upper + Lower
Rails & Frame Wall Mount fit into
the corresponding holes that are
not drilled thru the side panels.
Lower the Shelves (D) onto the Small
Cam Posts (O). Turn the Shelf Cam
Locks clockwise with a Phillips
screwdriver to lock the Shelves onto
the posts.
Install four Small Cam Posts (O) into the shelf adjustment holes for each shelf. Make sure
that all four posts are in the same height hole (front to back / side to side).
Install the six Short Hex Screws (K) into the pre-drilled holes on the backside of the Frame
Wall Mount (E) using the Hex Tool.
Install the six Short Phillips Screws (N) into the pre-drilled holes on the bottom of the Back
Panels (J) using a Phillips screwdriver.

©2015 ECR4KIDS, LP Version: ELR-17100—17102_EP_2015.03.18
Care and Cleaning
Clean wood with a damp cloth or sponge
using warm water and mild soap. Wipe dry.
Do not place near heat, moisture or
vaporizer which may cause wood to warp
and peel.
Check for loose or worn parts periodically
and tighten or replace as necessary.
Record the manufacture date here.
Information is located on the Batch ID
sticker and on the shipping carton.
Save this sheet in an accessible place.
Model Number: ELR-17100-A
(circle one) ELR-17101-A
ELR-17102-A
Factory Code: EP
Manufacture Date:
Batch ID Number:
(Located on Part C)
We appreciate your purchase of the Book Case.
ECR4KIDS has made every effort to supply a quality product that with proper
use and care, will provide many years of trouble-free use.
Warranty: Visit our website for product specific warranty information at:
www.ecr4kids.com
If you experience any difficulties with this product, please email us at
[email protected] or call toll-free at (855) ECR-4KIDS
(Monday - Friday, 7:00am - 4:00pm Pacific Standard Time)
Please do not return to place of purchase as ECR4KIDS will
replace defective part(s) and/or product.
To prevent a tip-over tragedy:
Buy and install low-cost anchoring devices that can prevent TVs,
dressers, bookcases and other furniture from tipping. For more
information please visit www.ecr4kids.com/resources