ECR 4 Kids ELR-0425-B User manual

J
Use the
Hex Tool
Use a Phillips
Screwdriver
Use a Phillips
Screwdriver
C
D
E
F
G
H
I
Top Panel (1)
Left & Right Side Panels (1/1)
Parts List
A
B
BEFORE ASSEMBLING, MAKE SURE YOU HAVE ALL THE PARTS
Upper Dividers (4)
Lower Dividers (4)
Upper Back Panels (5)
Lower Back Panel (1)
Hex Screws (32)
Cam Posts & Cam Locks (16/16)
L1
L2
K1
A1 A2
K2
Bottom Shelf (1)
Upper Shelf (1)
Lower Shelf (1)
Batch ID Sticker
located on underside
Hanger Hooks (10)Hanger Hook Posts
& Screws (12/12)
K
L M
5 Section Coat Locker
Model# ELR-0425-B
Adult Assembly Required.
Two adults recommended.
- Contains small parts, sharp points and edges.
- Do not stand, sit, kneel, climb, lean or pull on unit for support.
- Never leave children unattended.
- Do not place unit near high heat or moisture.
- Adult supervision recommended.
WARNING:
TOOLS INCLUDED
Hex Tool (1) TOOLS NEEDED
Phillips Screwdriver
San Diego, CA 92110 USA
www.ecr4kids.com
Children climbing on furniture
can lead to death or serious
injury due to tipping. Secure
unit to wall using appropriate
hardware.

1Insert Upper Dividers onto Upper Shelf
Connect the Top Panel
2
3Slide Middle Upper Back Panels into Place
Install the Lower Shelf
4
See Next Page
Align the slits on Upper Dividers (F) with the slit(s) on Upper Shelf (C) as shown,
and slide together until seated.
Install eight Cam Posts (K1) into the threaded plastic inserts on the underside of Top Panel (B)
with a Phillips screwdriver.
Reminder: Do not overtighten, as the plastic threads can be stripped.
Place two Cam Locks (K2) into the recessed holes on each Upper Divider (F) with the arrow
facing the closest edge.
Insert the Top Panel (B) Cam Posts into the holes on the top edge of the Upper Dividers (F).
Turn the Cam Locks clockwise with a Phillips screwdriver to lock the Upper Dividers (F) onto
the posts.
Install the Lower Shelf (D) onto the Upper Dividers (F) as shown, with eight Hex Screws (J)
using the Hex Tool.
Slide three Upper Back Panels (H) into the grooves on the Upper Dividers (F) as shown,
until fully seated into the groove on the underside of the Top Panel (B).
Tip: If the Back Panels (H) do not slide in easily, wiggle the panels while pushing into place.

5Connect the Lower Dividers
Install the Bottom Shelf
6
7Slide Remaining Back Panels into Place
Install the Right Side Panel
8
Batch ID Sticker See Next Page
Install eight Cam Posts (K1) into the threaded plastic inserts on the underside of Lower Shelf (D)
with a Phillips screwdriver.
Reminder: Do not overtighten, as the plastic threads can be stripped.
Place two Cam Locks (K2) into the recessed holes on each Lower Divider (G) with the arrow
facing the closest edge.
Attach the Lower Dividers (G) onto the Cam Posts on the underside of the Top Panel (B), turn the
Cam Locks clockwise with a Phillips screwdriver to lock the Lower Dividers (G) onto the posts.
Install the Bottom Shelf (E) onto the Lower Dividers (G) with eight Hex Screws (J)
using the Hex Tool. Install the Right Side Panel (A2) onto the Top Panel (B), Upper/Lower/Bottom Shelves(C/D/E)
with eight Hex Screws (J) using the Hex Tool.
Slide the remaining Upper Back Panels (H) into the grooves on Top Panel (B) & Lower Shelf (D)
as shown, until fully seated into the groove on the sides of Upper Dividers (F).
Slide the Lower Back Panel (I) into the grooves on Lower Shelf (D) & Bottom Shelf (E) as shown,
until centered on Bottom Shelf (E).
Tip: If the Back Panels (H/I) do not slide in easily, wiggle the panels while pushing into place.

9Install the Left Side Panel
Install the Hanger Hooks
10
C
a
r
e
f
u
l
l
y
R
o
t
a
t
e
U
p
r
i
g
h
t
©2015 ECR4KIDS, LP Version: ELR-0425-B_EP_2015.03.18
Care and Cleaning
Clean wood with a damp cloth or sponge
using warm water and mild soap. Wipe dry.
Do not place near heat, moisture or
vaporizer which may cause wood to warp
and peel.
Check for loose or worn parts periodically
and tighten or replace as necessary.
Record the manufacture date here.
Information is located on the Batch ID
sticker and on the shipping carton.
Save this sheet in an accessible place.
Model Number: ELR-0425-B
Factory Code: EP
Manufacture Date:
Batch ID Number:
(Located on Part E)
Install the Left Side Panel (A1) onto the Top Panel (B), Upper/Lower/Bottom Shelves(C/D/E)
with eight Hex Screws (J) using the Hex Tool.
Two Adults Recommended: Carefully rotate the unit upright.
Install two Hanger Hooks (M) to each locker section by threading the Hanger Hook
Posts & Screws (L1/L2) together from both sides of Left/Right Side Panels (A1/A2)
and Upper Dividers (F).
We appreciate your purchase of the 5 Section Coat Locker.
ECR4KIDS has made every effort to supply a quality product that with proper
use and care, will provide many years of trouble-free use.
Warranty: Visit our website for product specific warranty information at:
www.ecr4kids.com
If you experience any difficulties with this product, please email us at
[email protected] or call toll-free at (855) ECR-4KIDS
(Monday - Friday, 7:00am - 4:00pm Pacific Standard Time)
Please do not return to place of purchase as ECR4KIDS will
replace defective part(s) and/or product.
To prevent a tip-over tragedy:
Buy and install low-cost anchoring devices that can prevent TVs,
dressers, bookcases and other furniture from tipping. For more
information please visit www.ecr4kids.com/resources