Edelbrock 5226 User manual

©2002 Edelbrock Corporation
Catalog #5226 Page 1 of 2 Rev. 5/02
Please study these instructions carefully before installing your new strut tower brace. If you have any questions or problems,
contact our Technical Hotline at: 1-800-416-8628, 7 am - 5 pm, Monday through Friday, Pacific Standard Time or e-mail
us at [email protected].
Application: Designed for 1985-1992 Camaros and Firebirds (except 1987-1992 Formula) with Tuned Port Injection V8s. This
brace triangulates the front end and reduces chassis flex. This stiffens the chassis for improved cornering and more
responsive steering.
Tools Needed: In addition to common hand tools (7/16" & 9/16" wrenches, allen wrench, 3/8" 12-point socket or wrench),
you will need a tape measure and a 3/8" drill bit and drill.
INSTALLATION
1. Loosely assemble all parts as shown in
Figure 1 . Note which direction the main brace outside support brackets face
(Figures 2 & 3) .
2. Use a tape measure to find the center of the firewall, and locate the rear support bracket so that its leading edge is flush
with the front edge of firewall. Measure from the inside of each fender to find center. Mark the location of the bolt holes
and drill two 3/8" holes.
NOTE: The engine is not centered in the engine compartment; do not use the engine as a guide for centering the Strut
Tower Brace!
3. Install two short button head allen bolts, nuts, and washers to hold the rear support bracket in position, but do not tighten
at this time.
4. With the Strut Tower Brace
loosely assembled using two
long button head allen bolts to
the tubular braces, locate main
brace outside support brackets
over strut towers. Mark position
and drill two 3/8" holes on each
side. Note that there should be
1/8" to 1/4" air gap between
the manifold plenum top and
the strut tower brace.
5. Install and tighten all remaining
nuts, bolts and washers.
Edelbrock Strut Tower Brace
Catalog #5226
1985-1992 Camaros and Firebirds
(Except 1987-1992 Formula)
INSTALLATION INSTRUCTIONS
Fig. 1
Strut Tower Brace #5226 installed on late model Camaro with TPI V8

©2002 Edelbrock Corporation
Catalog #5226 Page 2 of 2 Rev. 5/02
Figure 2
Short side to front
of car
Figure 3
Straight side to
inside of car
Main Brace Ouside
Support Brackets
KIT CONTENTS
Qty.Description
1 Main brace
2 Tubular support braces
2 Outside support brackets
1 Rear bracket (firewall)
2 3/8”-16” x 1” button head allen bolts
2 3/8”-16” x 1-1/2” button head allen bolts
4 3/8”-16 x 1” bolts
2 3/8”-16 x 2-3/4” 12-point bolts
10 3/8”-16 Nyloc nuts
10 3/8” AN washers {Install next to bolt head and nut on each 2-3/4”
bolt, under bolt heads of 1” button head allen bolts, and under bolt
heads of four 1” 12-point bolts}
8 3/8” flat washers {Install against nuts on four outside support
bracket bolts (1” 12-point) and four button head allen bolts}
Please complete and mail your warranty card. Be sure to write the model number in the “Part #” space. Thank you.
Edelbrock Corporation
2700 California Street
Torrance, CA 90503
Tech Line: 1-800-416-8628
E-mail: [email protected]