Edelbrock 67452 User manual

Catalog #67452, #67453
©2006 Edelbrock Corporation Page 1 of 2
Brochure #63-67452
Rev. 5/06 - DA/mc
®
SHORTY HEADER
For 1994-1995 Ford Mustang, Capri, Mark,
5.0L (302 V8) with E.F.I., Auto/Std. Transmission
Catalog #67452, #67453
INSTALLATION INSTRUCTION
Please study these instructions carefully before installing your new Shorty Header . If you have any questions, please
contact our Technical Hotline at : 1-800-416-8628 from 7 am - 5pm, Monday-Friday, Pacific Standard Time or e-mail
us at [email protected]. Please fill out and mail your warranty card.
SHORTY HEADER: These components are designed as a system to improve the exhaust efficiency of the Ford 5.0 liter
V8 engine with E.F.I. (Electronic Fuel Injection). These tubular manifolds are a direct replacement for the factory exhaust
manifolds. A performance gain can be expected by the installation of the system. This system requires no welding
for installation and retains all O.E.M. emissions equipment.
Suggested Tools Needed for Installation: This vehicle has some metric fasteners.
❑ 3/8” ratchet socket set with extensions and sockets
❑Combination set of open-end wrenches
❑ Jackstands, screwdrivers, pliers, crescent wrench, etc.
❑ Liquid penetrant, anti-seize compound
SPECIAL NOTICE: This Edelbrock Shorty Header has received an Executive Order number (E.O.#) from the California Air
Resources Board (C.A.R.B.) making it legal for street use in all 50 states. To assist you with emission equipment
certification, we have included a silver fan shroud decal to help testing personnel verify the this part is a legal replacement
on the vehicle for which it is cataloged. The adhesive-backed decal should be affixed next to the existing emission and
engine specifications decal. Do not cover any part of your original emission decal.
WARNING: The use of "Thermal Wrap" or any aftermarket coating process will void the warranty on your Edelbrock
Shorty Header. Those products can cause excessive heat and moisture buildup resulting in corrosion and failure of the
system.
CAUTION: Due to higher underhood temperatures generated by shorty header, vehicles equipped with original spark plug
wires should have them replaced with high temperature plug wires for longer life.
IMPORTANT NOTE:
Proper installation is the responsibility of the installer. Improper installation will void warranty and may
result in poor performance and engine or vehicle damage.

Catalog #67452, #67453
©2006 Edelbrock Corporation Page 2 of 2
Brochure #63-67452
Rev. 5/06 - DA/mc
Disassembly
1. Disconnect negative cable from battery.
2. Use penetrating oil on all nuts and bolts to be
removed. This will prevent the possibility of broken or
stripped nuts and bolts.
3. Unbolt exhaust pipes from both exhaust manifolds.
4. Remove EGR tube from right side.
5. Unbolt and remove both exhaust manifolds.
6. Clean and inspect all sealing surfaces before
assembly.
Assembly - Left Side
1. With manifold port gasket in place, start a header bolt
with lock and flat washer in the rearmost bolt hole
leaving enough room for the manifold to slip into
position.
2. Start balance of header bolts with lock washers and
tighten evenly.
INSTALLATION INSTRUCTIONS
Edelbrock Corporation
2700 California St.
Torrance, CA 90503
Tech Line: 1-800-416-8628
E-Mail: [email protected]
KIT CONTENTS
Catalog #67452 (Ceramic-Coated), #67453 (Ti-Tech Coated)
Qty.Description Qty.Description
❑1 Manifold left side #25-9269 (#67452) ❑2 Coupler band clamps
❑1 Manifold right side #25-9270 (#67452) ❑2 Manifold port gaskets
❑ 1 Manifold left side #25-9036 (#67453) ❑2 Connector gaskets
❑ 1 Manifold right side #25-9141 (#67453) ❑ 12 Lock nuts, cad-plated; 3/8”-16
❑1 Manifold left side (B section) #25-9103 ❑ 14 Socket head cap screws; 3/8”-16 x 1/4”
❑1 Manifold right side (B section) #25-9104 ❑4 Tie wraps; 11”
❑1 Cat. adapter left (3”) #25-9622 ❑ 20 Split lock washers; 5/16”
❑1 Cat. adapter right (3”) #25-9623 ❑6 Hardened washers; 5/16” i.d. x 3/4” o.d.
❑ 20 Header bolts; 5/16”-18 x 1”
Assembly - Right Side
1. With gasket in place, start all bolts except the rear bolt
with lock and flat washers on each.
2. Start rear bolt with A.I.R. tube support bracket in
place.
3. Tighten balance of header bolts evenly.
4. Re-attach exhaust pipes to TES manifolds using your
original nuts.
5. Reinstall EGR tube.
6. Connect all parts including battery.
7. Start engine and bring up to normal running
temperature, then turn off and let cool.
8. When cool, re-tighten all manifold nuts and bolts.
®