edelkrone SliderPlus PRO V5 User manual

http://edel.kr/sld5
V5
TABLE OF CONTENTS
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
WHAT’S IN THE BOX & THE BASICS
ATTACHING THE BELTS & TENSION ADJUSTMENT
ATTACHING THE BELTS & TENSION ADJUSTMENT
LEGS & ANGLE ADJUSTMENT
MOUNTING SLIDERPLUS ON TRIPOD
MOUNTING YOUR CAMERA ON SLIDERPLUS
MOUNTING YOUR MAGIC ARM ON SLIDERPLUS
INCLINED MOTION
CLEANING KIT
CAUTIONS AND TIPS

1. WHAT’S IN THE BOX & THE BASICS
4
6
5
2
3
8
7
1
10
11
12
9
7.
8.
9.
10.
11.
12.
Rubber feet
Built-in foldable legs
Magnetic belt clip slot
3/8”-16 pop-up screw
1/4” mounting port
Instant locking mechanism
1.
2.
3.
4.
5.
6.
Incline
Mounting wheel for 3/8”-16 mounting port
Cleaning kit (x3)
2.5mm-3mm allen keys
Motion control belt (x2)
Manual control belt (x2)
1
24
3
1. Attach either the manuel control belt or the
motion control belt depending on use.
2. Remove the wheel.
3. Pass the belt through the hole.
4. Attach the wheel back.
2. ATTACHING THE BELTS & TENSION ADJUSTMENT
A detailed video explaining how to attach the belts details can be found at:
http://edel.kr/sld5

1
1. Attach the other head of belt.
2. If belt tension is low, you may increase it by
loosening the side wall screws and pulling out
the side walls until desired tension is achieved.
3. ATTACHING THE BELTS & TENSION ADJUSTMENT
A detailed video explaining how to attach the belts details can be found at:
http://edel.kr/sld5
2
4. LEG & ANGLE ADJUSTMENT
A detailed video explaining how to leg adjustment details can be found at:
http://edel.kr/sld5
1
2
3
To adjust the legs,
1. Loosen the wheel by turning it
counterclockwise.
2. Legs are adjustable at each 15°. Adjust
the leg at an appropriate angle.
3. Tighten the wheel by turning it
clockwise.

5. MOUNTING YOUR SLIDERPLUS TO YOUR TRIPOD
A detailed video explaining the process can be found at:
http://edel.kr/sld5
Detach tripod head from your tripod.
Place your SliderPLUS onto your tripod’s 3/8”-16 mounting screw.
Mount using the mounting wheel.
1.
2.
3.
1
2
3
6. MOUNTING YOUR CAMERA TO YOUR SLIDERPLUS
A detailed video explaining the mounting process can be found at:
http://edel.kr/sld5
SliderPLUS has 3/8”-16 screw for your tripod head hidden inside. You can
access this screw with the help of a coin. Using a coin, turn the screw until it
pops out. To hide the screw back again just press it down and turn it counter
clockwise.
Place your tripod head on the screw and tighten clockwise.
Attach your camera to your tripod head.
1.
2.
3.
1
2
3

1. You can mount any camera head or arm to your SliderPLUS with 1/4” mounting screw.
1/4” Mounting
Hole
1
7. MOUNTING YOUR MAGIC ARM ON SLIDERPLUS 8. INCLINED MOTION
A detailed video explaining inclined motion can be found at:
http://edel.kr/sld5
To get inclined shots,
1. Place your SliderPLUS onto 3/8”-16 mounting screw of your tripod head.
2. Attach your FlexTILT Head or any camera head onto your SliderPLUS.
3. You should attach your Slide Module to incline side of the SliderPLUS.
4. You should tighten the slide tension of the Slide Module to get inclined motion.
5. Place your camera to FlexTILT Head or any camera head.
3
4
2
5
1
A detailed video explaining mounting process can be found at:
http://edel.kr/sld5
If you are not able to slide manually after inclined operation, try loosening the tension.
Make as small adjustments as possible.
Please make sure that your tripod legs are opened widely enough to prevent falls and
balance issues.
!
!

9. CLEANING KIT
1
A detailed video explaining how to use cleaning kit details can be found at:
Separate the slider upper and lower carriages while your slider is resting on a flat
surface as shown.
Remove a double sided sticker from the cleaning kit.
Stick one side of sticker on slider rail as shown and peel off the white cover from
the sticker.
Slide the slider cars from one end to the other to clean the wheels.
Repeat this process for all wheels.
1.
2.
3.
4.
5.
3
4
2
http://edel.kr/sld5
10. CAUTIONS AND TIPS
A detailed video explaining the application usage details can be found at:
In order to get perfect results with you
SliderPLUS please attach your
SliderPLUS directly to tripod legs,
not to tripod head.
Please contact our dedicated customer care team for recommended tripod legs.
If your tripod has a feature that allows you
to extend the height from its neck, we suggest
keeping it down and as tight as possible in
order to prevent a rainbow effect.
1.
2.
http://edel.kr/sld5

SliderPLUS can travel twice its own length when it’s mounted on a tripod.
When using it on its feet, it can only travel its own length.
Always keep your slider locked
while it is not in use.
Use built-in foldable legs to level
your system.
Please make sure that your SliderPLUS
withstands within the area of the tripod legs
to prevent falls and balance issues.
Always make sure that your system is leveled
and balanced.
3.
4.
5.
For more tips please watch the user’s manual videos at: http://edel.kr/sld5
4
5
www.edelkrone.com
DISCLAIMER
edelkrone cannot be held responsible for damage caused by improper use or modification
of the product.
For more information and tips about your SliderPLUS, please watch the user’s
manual videos at:http://edel.kr/sld5