Edimax EW-7326Ig User manual

Multi-Languages QIG in Driver CD
================================================
Český: Českého průvodce rychlou instalací naleznete na
přiloženém CD s ovladači
Deutsch: Finden Sie bitte das deutsche QIG beiliegend in der
Treiber CD
Español: Incluido en el CD el QIG en Español
Français: Veuillez trouver l’français QIG ci-joint dans le CD
Italiano: Incluso nel CD il QIG in Italiano
Magyar: A magyar telepítési útmutató megtalálható a mellékelt
CD-n
Nederlands: De nederlandse QIG treft u aan op de bijgesloten
CD
Polski: Skrócona instrukcja instalacji w języku polskim znajduje
sięna załączonej płycie CD
Português: Incluído no CD o QIG em Portugues
Русский: Найдите QIG на pусскoмязыке на приложеном CD
Romana: Cd-ul cuprinde Ghid de instalare rapida in limba romana
Slovensky: Anglického sprievodcu rýchlou inštaláciou nájdete na
priloženom CD s ovládačmi.
Türkçe: Ürün ile beraber gelen CD içinde Türkçe HızlıKurulum
Kılavuzu'nu bulabilirsiniz

0
COPYRIGHT
Copyright ©2005/2006 by Edimax Technology Co. Ltd. All rights reserved. No part of this
publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or
translated into any language or computer language, in any form or by any means, electronic,
mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written
permission of this company
This company makes no representations or warranties, either expressed or implied, with
respect to the contents hereof and specifically disclaims any warranties, merchantability or
fitness for any particular purpose. Any software described in this Quick Installation Guide is
sold or licensed "as is". Should the programs prove defective following their purchase, the
buyer (and not this company, its distributor, or its dealer) assumes the entire cost of all
necessary servicing, repair, and any incidental or consequential damages resulting from
any defect in the software. Further, this company reserves the right to revise this publication
and to make changes from time to time in the contents hereof without obligation to notify
any person of such revision or changes.

1
Content
1. Product Information .................................................................................2
2. Product Package ......................................................................................2
3. Hardware Installation ...............................................................................3
4. Software Installation.................................................................................3
5. Connect to Wireless Access Point..........................................................7
5.1 Using Realtek Wireless Configuration Utility...................................7
5.2 Using Windows Zero Config............................................................ 11
6. Federal Communication Commission Interference Statement ..........15
7. R&TTE Compliance Statement ..............................................................16

2
1. Product Information
Thank you for your purchasing Edimax Wireless 802.11b/g PCI Adapter. This
PCI adapter is designed to comply with IEEE 802.11b/g Wireless LAN standard
and easy to carry with the Mini size. It is suitable for any Desktop computers.
This adapter supports higher data throughput than the IEEE 802.11b/g
standard (up to 54Mbps). It supports specific ways to increase the data transfer
rate at a time; compress the data and decrease the waiting time to send the
next data to the Routers or Access Points. When the adapter is connecting to
the Routers or Access Points with the proprietary feature, the wireless network
will be more effective.
Main Features
zComplies with IEEE 802.11b/g Standards.
zSupports data transfer rate up to 54Mbps.
zSupports high throughput for multi-media data bandwidth requirement.
zSupport 64/128-bit WEP, WPA & WPA2 Encryption.
zSupports operating system: Windows 98SE/Me/2000/XP/Vista and Linux
zSupports 32-bit PCI interface.
2. Product Package
Before you starting to use this Wireless PCI Adapter, please check if there’s
anything missing in the package, and contact your dealer of purchase to claim
for missing items:
One Wireless PCI Adapter
One 2dBi Antenna
One Quick Installation Guide
One CD-ROM (Including Multi-language QIG, User’s Manual and
Driver/Utility)

3
3. Hardware Installation
A. Turn off your computer and remove its cover.
B. Insert the PCI card to an available PCI slot firmly.
C. Secure this card to the rear of the computer chassis and put back the
cover.
D. Secure the antenna to the antenna connector of the card.
E. Turn on the computer.
4. Software Installation
This wizard can be run in Windows 2000/XP/XP64/2003/Vista. The following
procedures are operated in Windows XP. (Procedures are similar for Windows
2000/XP/XP64/Vista.)
1. Insert the CD shipped along with the product into your CD-ROM drive. The
Windows Vista will popup AutoPlay window, Please select “Install or run
program” to execute Autorun.exe program. The Autorun.exe program
should be executed automatically. If not, run Autorun.exe manually from
“Autorun” folder in the CD.
2. The follow ing screen will be displayed. Click “Setup Utility” to run the setup
wizard.
Please select ‘Allow’ if Windows indicates that ‘an unidentified program
wants access to your computer’.

4
3. Select the Setup Language and click “OK” to proceed.
4. Click “Next” to start installing driver and utility.

5
5. Select the Region Domain for which WLAN is authorized to use and click
“Next” to continue.
6. Radio regulation warning window. Due to the Radio regulation at different
area, different radio law might be applied. Please make sure your region
selection is correct.

6
7. The system starts to install the driver and utility.
8. Click “Finish” to complete the driver and utility installation.

7
5. Connect to Wireless Access Point
Using Configuration Utility to Connect to Wireless Access Point
5.1 Using Realtek Wireless Configuration Utility
1. After installation is complete, wireless configuration utility will be shown an
icon at your windows desktop as below. Please click the icon by right
mouse key to lunch the configuration utility.
2. Configuration utility will scan for wireless access points automatically, and
all found access points will be displayed on “Available Network”. Please
select an access point you wish to connect, and click ‘Add to Profile’. If the
wireless access point you want to connect does not show here, please
click ‘Refresh’

8
3. If the wireless access point uses encryption, you have to input WEP
passphrase or WPA preshared key. Please ask the owner of the wireless
access point you want to connect, and input the correct passphrase /
preshared key at “Network key” & “Confirm network key”, then click ‘OK’.
If the value you inputted here is wrong, you will not be able to connect to
wireless access point. Authentication type is selected automatically, please
don’t change it.

9
4. The utility will automatically add the access point at Wireless Utility Profile.

10
5. If the wireless access point is successfully connected, you’ll see a
connected icon displayed at the lower-left corner of wireless
configuration utility window and click ‘Close’ to exit.

11
5.2 Using Windows Zero Config
1. After lunch wireless configuration, Please select “Windows Zero Config” and
click “OK” to disable the utility of the adapter..
2. Please lunch Windows Zero Config by double-click the wireless connection
icon in the lower-left corner on Windows desktop.

12
3. The Windows Zero Config Panel will pup-up. Please select the wireless
access point which you want to connect and click “Connect”

13
4. If the wireless access point without encryption, there is warning window will
pup-up. Please click “Connect Anywhere”.

14
5. When you see the “Connected” shows on the Windows Zero Config window,
the wireless is successfully connected.

15
6. Federal Communication Commission Interference
Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications.However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
4. Consult the dealer or an experienced radio technician for help.
FCC Caution
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
Any changes or modifications not expressly approved by the party responsible for
compliance could void the authority to operate equipment.
Federal Communications Commission (FCC) Radiation Exposure
Statement
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with a
minimum distance of 20 centimeters between the radiator and your body.

16
7. R&TTE Compliance Statement
This equipment complies with all the requirements of DIRECTIVE 1999/5/EC OF THE
EUROPEAN PARLIAMENT AND THE COUNCIL of March 9, 1999 on radio equipment and
telecommunication terminal Equipment and the mutual recognition of their conformity
(R&TTE)
The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications
Terminal Equipment and Satellite Earth Station Equipment) As of April 8, 2000.
Safety
This equipment is designed with the utmost care for the safety of those who install and use it.
However, special attention must be paid to the dangers of electric shock and static electricity
when working with electrical equipment. All guidelines of this and of the computer
manufacture must therefore be allowed at all times to ensure the safe use of the equipment.
EU Countries Intended for Use
The ETSI version of this device is intended for home and office use in Austria, Belgium,
Denmark, Finland, France, Germany, Greece, Ireland, Italy, Luxembourg, Bulgaria, Cyprus,
Czech Republic, Estonia, Hungary, Latvia, Lithuania, Malta, Poland, Romania, Slovakia,
Slovenia, the Netherlands, Portugal, Spain, Sweden, and the United Kingdom.
The ETSI version of this device is also authorized for use in EFTA member states: Iceland,
Liechtenstein, Norway, and Switzerland.
EU Countries not intended for use
None
Please check the declaration of conformity on www.edimax.com

17