Edimax IAP1200 User manual

IAP1200
User Manual
05-2021 / v1.3

CONTENTS
I. Product Information...............................................................................1
I-1. Package Contents ..................................................................................................................1
I-2. System Requirements............................................................................................................2
I-3. Hardware Overview...............................................................................................................2
I-4. LED Status ..............................................................................................................................3
I-5. Reset ......................................................................................................................................4
I-6. Safety Information.................................................................................................................5
II. Quick Setup............................................................................................5
II-1. Initial Setup............................................................................................................................6
II-2. Managed AP Mode: Edimax Pro NMS .................................................................................11
III. Wall Installation...................................................................................15
IV. Browser Based Configuration Interface.................................................18
IV-1. Information........................................................................................................................20
IV-1-1. System Information ...........................................................................................................20
IV-1-2. Wireless Clients..................................................................................................................24
IV-1-3. Wireless Monitor ...............................................................................................................26
IV-1-4. DHCP Client Table ..............................................................................................................28
IV-1-4. DHCP Client Table ..............................................................................................................28
IV-1-5. Log......................................................................................................................................29
IV-2. Network Settings ...............................................................................................................31
IV-2-1. LAN-Side IP Address...........................................................................................................31
IV-2-2. LAN Port.............................................................................................................................33
IV-2-3. IGMP Snooping ..................................................................................................................34
IV-2-4. VLAN ..................................................................................................................................35
IV-3. Wireless Settings................................................................................................................36
IV-3-1. 2.4GHz 11bgn.....................................................................................................................36
IV-3-1-1. Basic .............................................................................................................................36
IV-3-1-2. Advanced .....................................................................................................................39
IV-3-1-3. Security ........................................................................................................................41
IV-3-1-3-1. No Authentication .....................................................................................................43
IV-3-1-3-2. WEP............................................................................................................................43
IV-3-1-3-3. IEEE802.1x/EAP..........................................................................................................43
IV-3-1-3-4. WPA-PSK ....................................................................................................................43
IV-3-1-3-5. WPA-EAP....................................................................................................................44
IV-3-1-3-6. Additional Authentication .........................................................................................44

IV-3-1-4. WDS .............................................................................................................................46
IV-3-1-5. Guest Network.............................................................................................................48
IV-3-2. 5GHz 11ac 11an .................................................................................................................49
IV-3-2-1. Basic .............................................................................................................................49
IV-3-2-2. Advanced .....................................................................................................................51
IV-3-2-3. Security ........................................................................................................................53
IV-3-2-4. WDS .............................................................................................................................55
IV-3-2-5. Guest Network.............................................................................................................57
IV-3-3. WPS......................................................................................................................................58
IV-3-4. RADIUS .................................................................................................................................60
IV-3-4-1. RADIUS Settings ...........................................................................................................61
IV-3-4-2. Internal Server .............................................................................................................63
IV-3-4-3. RADIUS Accounts .........................................................................................................65
IV-3-5. MAC Filter ..........................................................................................................................67
IV-3-6. WMM...................................................................................................................................69
IV-3-7. Schedule...............................................................................................................................71
IV-3-8. Traffic Shaping .....................................................................................................................73
IV-4. Management .....................................................................................................................74
IV-4-1. Admin.................................................................................................................................74
IV-4-2. Date and Time....................................................................................................................76
IV-4-3. Syslog Server......................................................................................................................78
IV-4-4. Ping Test.............................................................................................................................79
IV-5. Advanced ...........................................................................................................................80
IV-5-1. LED Settings .......................................................................................................................80
IV-5-2. Update Firmware...............................................................................................................81
IV-5-3. Save/Restore Settings........................................................................................................82
IV-5-4. Factory Default ..................................................................................................................84
IV-5-5. Reboot ...............................................................................................................................85
IV-6. Operation Mode ................................................................................................................86
V. Appendix .............................................................................................87
V-1. Configuring your IP address...............................................................................................87
V-1-1. Windows XP .......................................................................................................................88
V-1-2. Windows Vista ...................................................................................................................90
V-1-3. Windows 7 .........................................................................................................................92
V-1-4. Windows 8 .........................................................................................................................96
V-1-5. Mac ..................................................................................................................................100

OVERVIEW
Your access point can function in two different modes.
The default mode for your access point is AP mode.
AP mode is a regular access point for use in your wireless network.
Managed AP mode acts as a “slave” AP within the AP array (controlled by the
AP Controller “master”).

1
I. Product Information
I-1. Package Contents
Quick Installation Guide
Screws x 2
IAP1200 (US)
IAP1200 (EU)
or

2
I-2. System Requirements
-Ethernet cable
-PoE Switch
-Computer with web browser for access point configuration
I-3. Hardware Overview
RJ11 Pass-Through
LEDs
Reset Button
RJ11 Pass-Through
RJ45 Ethernet Port
RJ45 Ethernet Port

3
I-4. LED Status
LED
LED Color
Status
Description
Power
(Right)
Green
On
The access point is on.
Flashing
The access point is starting up.
LAN
(Left)
Green
On
LAN port is connected.
Green
Flashing
LAN activity
Orange
Flashing
Locating access point.
Green &
Orange
Flashing/
Alternating
Upgrading firmware. Do not switch off.

4
I-5. Reset
If you experience problems with your access point, you can reset the device
back to its factory settings. This resets all settings back to default.
1. Press and hold the reset button on the access point for at least 10
seconds. Then release the button.
You may need to use a pencil or similar sharp object to push the
reset button.
2. Wait for the access point to restart. The access point is ready for setup
when the green power LED is on.

5
I-6. Safety Information
In order to ensure the safe operation of the device and its users, please read
and act in accordance with the following safety instructions.
1. The access point is designed for indoor use only; do not place the access
point outdoors.
2. Do not place the access point in or near hot/humid places, such as a kitchen
or bathroom.
3. Do not pull any connected cable with force; carefully disconnect it from the
access point.
4. Handle the access point with care. Accidental damage will void the
warranty of the access point.
5. The device contains small parts which are a danger to small children under
3 years old. Please keep the access point out of reach of children.
6. Do not place the access point on paper, cloth, or other flammable materials.
The access point may become hot during use.
7. There are no user-serviceable parts inside the access point. If you
experience problems with the access point, please contact your dealer of
purchase and ask for help.
8. The access point is an electrical device and as such, if it becomes wet for
any reason, do not attempt to touch it without switching the power supply
off. Contact an experienced electrical technician for further help.
1. If you smell burning or see smoke coming from the access point or power
adapter, then disconnect the access point and power adapter immediately,
as far as it is safely possible to do so. Call your dealer of purchase for help.
II.Quick Setup
Your access point can be up and running in just a few minutes. It can function
as a standalone access point (AP mode) or as part of an AP array (Managed AP
mode).

6
For use a Managed AP in an AP array, the access point will automatically
switch mode when an AP Controller is configured as described in Edimax Pro
NMS.
II-1. Initial Setup
1. Connect the IAP1200’s rear Ethernet port to a PoE switch (LAN port) using
an Ethernet cable.
2. Use a computer that’s connected to the LAN or connect to the IAP1200’s
front Ethernet port using an Ethernet cable.
3. Open a web browser and enter the access point’s IP address in the address
field. The default IP address is 192.168.2.2
Your computer’s IP address must be in the same subnet as the AP
access point.

7
If you changed the access point’s IP address, or if your
gateway/router uses a DHCP server, ensure you enter the correct
IP address. Refer to your gateway/router’s settings.
4. Login with the default username & password: admin & 1234
5. You will arrive at the “System Information” screen shown below.

8
The next steps will help you to configure the following basic settings of the
access point:
-LAN IP Address
-2.4GHz & 5GHz SSID & Security
-Administrator Name & Password
-Time & Date
It is recommended you configure these settings before using the
access point.
1. To change the access point’s LAN IP address, go to “Network Settings” >
“LAN-side IP Address”and you will see the screen below.
2. Enter the IP address settings you wish to use for your access point. You
can use a dynamic (DHCP) or static IP address, depending on your network
environment. Click “Apply” to save the changes and wait a few moments
for the access point to reload.
When you change your access point’s IP address, you need to use
the new IP address to access the browser based configuration
interface instead of the default IP 192.168.2.2.
3. To change the SSID of your access point’s 2.4GHz wireless network(s), go
to “Wireless Setting” > “2.4GHz 11bgn” > “Basic”. Enter the new SSID for
your 2.4GHz wireless network in the “SSID1” field and click “Apply”.
To utilize multiple 2.4GHz SSIDs, open the drop down menu
labelled “Enable SSID number” and select how many SSIDs you

9
require. Then enter a new SSID in the corresponding numbered
fields below, before clicking “Apply”.
4. To configure the security of your access point’s 2.4GHz wireless
network(s), go to “Wireless Setting” > “2.4GHz 11bgn” > “Security”. Select
an “Authentication Method” and enter a “Pre-shared Key” or “Encryption
Key” depending on your choice, then click “Apply”.
If using multiple SSIDs, specify which SSID to configure using the
“SSID” drop down menu.
5. Go to “Wireless Settings” > “5GHz 11ac 11an” and repeat steps 3 & 4 for
the access point’s 5GHz wireless network.
6. To change the administrator name and password for the browser based
configuration interface, go to “Management” > “Admin”.

10
7. Complete the “Administrator Name” and “Administrator Password” fields
and click “Apply”.
8. To set the correct time for your access point, go to “Management” >
“Date and Time Settings”.
9. Set the correct time and time zone for your access point using the
dropdown menus. The access point also supports NTP (Network Time
Protocol) so alternatively you can enter the host name or IP address of a
time server. Click “Apply” when you are finished.
You can use the “Acquire Current Time from your PC” button if
you wish to set the access point to the same time as your PC.
10.The basic settings of your access point are now configured.

11
II-2. Managed AP Mode: Edimax Pro NMS
Edimax Pro Network Management Suite (NMS) supports the central
management of a group of access points, otherwise known as an AP Array.
NMS supports up to 16 Edimax Pro access points with no additional wireless
controller required or 128 access points with the APC 500 AP controller -
reducing costs and facilitating efficient remote AP management.
Edimax Pro NMS is simple to setup. An overview of the system is shown
below:
One AP (access point) is designated as the AP Controller (master) and other
connected Edimax Pro APs are automatically designated as Managed APs
(slaves). Using Edimax Pro NMS you can monitor, configure and manage all
Managed APs (up to 128) from the single AP Controller.
The IAP1200 functions as a Managed AP and cannot act as an AP
Controller.
When using an Edimax NMS AP controller, other connected APs are
automatically set to Managed APs. In the case that the AP Controller

12
cannot find your IAP1200 as a Managed AP, you can configure the
setting manually as below:
1. Ensure all APs including your IAP1200 are connected to an Ethernet or PoE
switch which is connected to a gateway/router.
You can use your router as a DHCP server or you can later
configure your AP Controller as a DHCP server.
2. Ensure all APs are powered on and check LEDs.
3. Connect the APC500 as the AP Controller which will manage all other
connected APs (up to 128 depending on model).

13
4. Connect a computer to the IAP1200 via PoE switch using an Ethernet
cable.
5. Open a web browser and enter the IAP1200’s IP address in the address
field. The default IP address is 192.168.2.2

14
Your computer’s IP address must be in the same subnet as the AP
Controller. If you changed the AP Controller’s IP address, or if
your gateway/router uses a DHCP server, ensure you enter the
correct IP address. Refer to your gateway/router’s settings.
6. Enter the username & password to login. The default username &
password are admin & 1234.
7. You will arrive at the Edimax Pro NMS Dashboard. Go to “Operation
Mode” and select “Managed AP Mode” from the drop down menu.
8. Click “Apply” to save the settings and your AP Controller & Managed APs
should be fully functional. Use Edimax NMS on your AP controller to
manage & monitor your Managed APs.
Refer to your AP controller’s user manual for help with Edimax
NMS.

15
III.Wall Installation
The IAP1200 In-Wall access point comes with EU or US wall plates per your
region and fits standard sized wall boxes. The Ethernet cable in your wall box
must be connected to a PoE switch.
1. Carefully remove the wall plate from the IAP1200 by pulling the plate with
a light force to unclip it.
2. Connect the PoE cable from your wall box the rear of the IAP1200.

16
3. Insert the IAP1200 into the wall box, taking care to position the cable
properly so it’s not strained.
4. Use the included screws to screw the IAP1200 securely into place and
ensure a flush fit with the wall.