Eizo eClient SX1 User manual

For Microsoft Windows XP Embedded
Version A
Please confirm the version of the software built in eClient, and refer to
the suited User's Manual (Refer to the User's Manual Version List on
next page).
This is the manual for the following software version.
* Microsoft Windows XP Embedded: Ver. 5.01 or later, Rev. 1.0.2 or later
* Microsoft Remote Desktop Connection Software: Ver. 5.2.3 or later
* Ctrix ICA Client Software: Ver. 8.0 or later
- For Administrator -

User’s Manual Version List
A handling description changes with versions of the software built in eClient. Please
refer to below.
NOTE
• The version of software built in eClient can be checked with a [System] tab of
[Start]- [About] menu.
OS: Microsoft Windows XP Embedded
Software
Manual
Microsoft Windows XP
Embedded
Microsoft Remote
Desktop Connection
Software
ICA Client
Software
A
(This manual)
Version 5.01 or later
Rev. 1.0.2 or later Version 5.2.3 or later Version 8.0 or later

SAFETY SYMBOLS
This manual uses the safety symbols below. They denote critical information. Please read them
carefully.
WARNING
Failure to abide b
y
the information in a WARNING ma
y
result in serious in
j
ur
y
and
can be life threatening.
CAUTION
Failure to abide by the information in a CAUTION may result in moderate injury
and/or property or product damage.
Indicates a prohibited action.
Indicates to ground for safety.
Copyright© 2004 EIZO NANAO CORPORATION. All rights reserved. No part of this manual
may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means,
electronic, mechanical, or otherwise, without the prior written permission of EIZO NANAO
CORPORATION.
EIZO NANAO CORPORATION is under no obligation to hold any submitted material or
information confidential unless prior arrangements are made pursuant to EIZO NANAO
CORPORATION's receipt of said information. Although every effort has been made to ensure
that this manual provides up-to-date information, please note that EIZO monitor specifications
are subject to change without notice.
ENERGY STAR is a U.S. registered mark.
Apple and Macintosh are registered trademarks of Apple Computer, Inc.
DPMS is a trademark and VESA is a registered trademark of Video Electronics Standards
Association.
VGA is a registered trademark of International Business Machines Corporation.
Windows is a registered trademark of Microsoft Corporation.
ScreenManager and PowerManager are trademarks of EIZO NANAO CORPORATION.
FlexScan and EIZO are registered trademarks of EIZO NANAO CORPORATION.
Sun, Sun Microsystems, and the Java logo are trademarks or registered trade marks of Sun
Microsystems, inc. in the United States and other countries.
As an ENERGY STAR®Partner, EIZO NANAO CORPORATION has determined
that this product meets the ENERGY STAR guidelines for energy efficiency.
3

TABLE OF CONTENTS
1. INTRODUCTION ..................................................................................... 5
1-1. General Description ......................................................................................5
1-2. Features ........................................................................................................5
1-3. Package Contents..........................................................................................6
1-4. Controllers & Connectors ............................................................................7
2. CONNECTION the eClient SX1 ............................................................. 9
2-1. Setting up the SX1 ........................................................................................9
3. OPERATION ......................................................................................... 15
3-1. Adding a Connection name.........................................................................15
3-2. Logging on or off the WTS .........................................................................20
3-3.Opening/Closing the Local Web Browser.....................................................24
4. Setup the environment of the operation (by the System Administrator ) .25
4-1. Note for the SX1 system environment ........................................................25
4-2. Log on to the SX1 as the System Administrator..........................................26
4-3. “User” authority and “Administrator” authority .......................................28
4-4. Using the control panel ...............................................................................30
4-5. [Start]-[About] menu ..................................................................................37
4-6. Software updating/Installation....................................................................38
5. TROUBLESHOOTING........................................................................... 39
6. CLEANING............................................................................................ 40
7. SPECIFICATIONS................................................................................. 41
4 TABLE OF CONTENTS
4

1. INTRODUCTION
Thank you very much for purchasing the EIZO eClient SX1.
1-1. General Description
The SX1 is used as a thin client, which connects to the terminal service installed
Windows Terminal Server (Hereafter defined WTS) as listed below and accesses
applications or data provided from the WTS.
• Server (WTS: Windows Terminal Server)
Microsoft Windows 2000 Server / Advanced Server / Datacenter Server
Microsoft Windows Server 2003 Standard Edition / Enterprise Edition / Datacenter
Edition
1-2. Features
• Lower TCO (Total Cost of Ownership)
• Saves Space and Power Consumption
• Less Heat, Less Noise
• SX1: Windows XP Embedded
• Serial Port for Modem/PDA (*Hayes AT compatible modem supported)
• 2 USB downstream ports (SX1: Standard Rev. 2.0)
• Local Web Browser added as a default connection
• PC card slot for modem card or LAN card
• Wake on LAN supported
• Network utility software, “Network Administrator Version 3.0” supported
• Two installation types; EIZO Monitor mounted / Stand alone
• EIZO Monitor detachable stand type
Output data of
applications
Input data from
keyboard/mouse/
stylus
Windows Terminal Server
(WTS)
eClient SX1
· Operation of applications
· Stora
g
e of data
⋅ Display data
⋅ Operation by keyboard/
mouse
Networ
k
1. INTRODUCTION 5

• Secondary power switch (wired)
1-3. Package Contents
Please contact your local dealer for assistance if any of the listed items are missing or
damaged. Please make sure that all the items listed are in the package.
•SX1
•Mouse (FDM-LCS1)
•Power Cord
•Switch Box (1.8 m)
•Signal Cable (FD-C29) (50 cm)
•User’s Manual
•Monitor Attachment Unit: for mounting monitor *1
•Power Cord (50 cm): for mounting monitor*1
•Clamp for cables: for mounting monitor*1
*
1
The monitor attachment unit, the power cord, and the clamp for cables are used when
attaching a monitor in SX1. Installation of a monitor should follow the system administrator.
NOTE
• A keyboard is not included. It must be purchased separately.
• Please use the enclosed mouse. EIZO NANAO CORPORATION will no be held
responsible for accident or damage caused by the use of a mouse manufactured by
other companies.
• We recommend that you retain the original packing materials in case of future need.
6 1. INTRODUCTION

1-4. Controllers & Connectors
Controllers
AC INPUT
AC OUTPUT
Power SYNC
OFF
ON
(1)
(2)
(3)
(4)
(5)
(1) Power Button
(2) Power Indicator
Power Indicator State of the unit
Blue
• Operation mode
• Screen saver is active
*1
• No picture is displayed on the monitor
*1, *2
Off Power is off (Wake on LAN standby)
*1
[Procedure to return to the operation mode]
- Operate the mouse or keyboard.
*2
The monitor is in the power save mode when the power save function of the
monitor is set.
(3) Connector for Switch Box*3
(4) Switch Box*3
(5) Power Supply Control Switch (POWER SYNC) *4
*3The secondary power switch makes it easy to turn the SC1 / SX1 on and off when
stowed away under the desk or out of reach. When the enclosed switch box is
connected to the connector, it can be used as a power button. The power button on
the SC1/SX1 can be used simultaneously even if the switch box is connected.
*4Please refer to pg. 12 for details on the power supply control switch (POWER
SYNC).
NOTE
• When turning off/on the unit, leave the unit off for a few seconds before turning it on
again.
• Do your part to conserve energy, turn off the unit when your finished using it.
Complete energy use can only be stopped by disconnecting the unit from the power
supply.
Left View Right View
* SX1 used as an example
1. INTRODUCTION 7

Connectors
AC INPUTAC INPUT
AC OUTPUTAC OUTPUT
Power SYNCPower SYNC
OFF OFF
ON ON
(3)
(2)
(1)
(8)
(9)
(11)
(10)
(6)
(5)
(4)
(12)
(7)
(1) Power Supply Control Switch (POWER SYNC)…Same with (5) on P.7
(2) Power Connector (AC output)
(3) Power Connector (AC input)
(4) Ethernet Connector (10 Base-T, 100 Base-TX)
(5) Parallel Connector
(6) Headphone Connector
Microphone Connector
(7) PC Card Slot
(8) USB Port (Downstream) x 2
(9) DVI-I Output Connector
(10) Serial Port (RS-232C)
(11) Mouse Connector
Keyboard Connector
(12) Security Lock*1
*1 This allows for connection of a security cable. This lock supports Kensington’s
MicroSaver security system. For further information, please consult:
Kensington Technology Group
2855 Campus Drive, San Mateo, CA 94403 USA
Tel: [phone], x3348
Intl: 650-572-2700 Fax: [phone]
http://www.kensington.com
8 1. INTRODUCTION

2. CONNECTION the eClient
SX1
This chapter explains how to connect the SX1 to a WTS.
2-1. Setting up the SX1
Please observe the following cautions when connecting the SX1.
WARNING
Place the eClient SX1 on a strong, stable surface.
A unit placed on an inadequate surface may fall, resulting in injury
or equipment damage. If the unit falls, disconnect the power
immediately and have the unit checked by a qualified service
engineer before using it again. Using a unit after it has been
dropped may result in fire or electric shock.
OK
Set the unit in an appropriate location.
Not doing so may result in fire, electric shock, or equipment
damage.
* Do not place outdoors.
* Do not place in the transportation system (ship, aircraft, trains,
automobiles, etc.)
* Do not place in a dusty or humid environment.
* Do not place in a location where the steam comes directly on the
screen.
* Do not place near heat generating devices or a humidifier.
The Monitor Attachment Unit supports only EIZO L767, L567,
L557, L367.
Mounting other monitors to the unit may result in injury or
equipment damage. Contact your system administrator for details
of the attachment.
* The illustrated monitors in this section are L567. Monitors
are not included in the package.
Maximum load capacity of AC outlet is 2 A.
Connecting unit with more than 2 A may result in fire, electric
shock or other damage.
2. CONNECTION the eClient SX1 9

Mounting EIZO monitor to the SX1
When using other monitors than EIZO, proceed to step 3.
The Monitor Attachment Unit of SX1 supports the EIZO L767, L567, L557, and L367,
so EIZO monitor mounted SX1 is available.
NOTE
• Prepare the following, when mounting a monitor to the SX1.
Monitor L767, L567, L557, L367
Screws The screws used for the monitor original stand
Power Cord Power Cord (50 cm) which is included into the SX1 package.
Mounting EIZO monitor procedure
Step 1
Step 2
ACINPUT ACINPUT
POO|PQOu‘Q‘ POO|PQOu‘Q‘
QOO|QSOu‘Q‘ QOO|QSOu‘Q‘
AC OUTPUTAC OUTPUT
Power SYNC Power SYNC
OFF OFF
ON ON
1. Attach the monitor attachment unit to the monitor.
(1) [1] Hold the center of the cover of the monitor attachment unit (upper side and
bottom side) and [2] slide them rightward or leftward to remove the covers.
Monitor Attachment Unit
Step 1. Attach the monitor attachment unit to the monitor.
Step 2.
Mount the monitor to the SX1.
[1][1]
[1]
[2] [2]
10 2. CONNECTION the eClient SX1

(2) Lay the LCD monitor down on the soft cloth or cushion not to scratch the panel
surface.
(3) Remove the original stand by loosening the screws.
(4) Attach the monitor attachment unit to the monitor securely, by using the screws,
which used for the original stand.
(5) Get back the cover to the monitor attachment unit.
2. Mount the monitor to the SX1.
(1) Fit the protruding portion of the monitor attachment unit (4 points) to the
attachment position of SX1 (4 points), and insert it in downward, by pressing
down the knob of the monitor attachment unit into the knob position of SX1.
NOTE
• Monitor mount positions
SC1 has three attachment position (Highest position, Middle position and
lowest position). Please be sure to attach in each position as follows.
• Refer to the P. Error! Bookmark not defined. for the dimensions figure
according to monitor size.
(2) Grip both side of the monitor firmly with both hands and adjust the monitor angle
as desired.
100 mm x 100 mm
for L567/L557/L767
75 mm x 75 mm
for L367
Highest position
Lowest position
Knob position
Middle
position
2. CONNECTION the eClient SX1 11

Connecting the signal cable and power cables
3. Plug the signal cable into the connector at the rear of the monitor
and the other end of the cable into the video connector on the DVI-I
connector of the SX1
4. After connecting, secure the connection with the screw-in fasteners.
5. Plug the power cord (50 cm), included into the package, into the
power connector on the rear of the monitor and the other end of the
cable into the power connector (AC outlet) of the eCleint, or into a
power outlet.
WARNING
Use the enclosed power cord and connect to the standard
power outlet of your country.
Be sure to remain within the rated voltage of the power cord.
Not doing so may result in fire or electric shock.
The equipment must be connected to a grounded main
outlet.
Not doing so may result in fire or electric shock.
Maximum load capacity of AC outlet is 2 A.
Connecting unit with more than 2 A may result in fire, electric
shock or other damage.
Power Supply Control Switch (POWER SYNC)
When the monitor's power cord is connected to the AC output power supply of
SC1/SX1, the monitor’s power supply can be linked with on/off of SC1/SX1. Choose
ON from the power supply control switch (POWER SYNC).
When the power button of SC1/SX1 is turned on or off…
Power Supply Control Switch
(POWER SYNC)
Power supply for the monitor
ON The monitor’s power supply is linked, and it turns on or
off simultaneously.
OFF (default) Since the monitor’s power supply is not linked, please
turn the monitor's power supply on or off independently.
12 2. CONNECTION the eClient SX1

NOTE
• Bundling cables
After all connection has been made, please bundle the cables with the clamp
included into the package, so that the cables do not obstruct the paths as follows.
• Clamp installation
AC INPUT AC INPUT
POO|PQOu‘Q‘POO|PQOu‘Q‘
QOO|QSOu‘Q‘QOO|QSOu‘Q‘
AC OUTPUTAC OUTPUT
PowerSYNC PowerSYNC
OFFOFF
ONON
Connecting the peripheral devices to SX1
NOTE
• Before connecting the SX1, confirm the following:
- The SX1 is turned off.
- The WTS is turned on.
• Connect the peripherals to the appropriate connectors of the unit.
6. In case of connecting the WTS through LAN:
Connect the SX1 to the network with an Ethernet cable.
In case of a dial-up or dial-in connection:
Connect the SX1 to a modem or a modem card.
NOTE
• Please remove the lid on the side of the SX1 before connecting a LAN card or
a modem card.
7. Plug a keyboard and a mouse into the SX1.
8. When using other devices, connect them to the appropriate
connectors.
2. CONNECTION the eClient SX1 13

9. The switch box is connected to the attached connector for Switch
box on the SX1 if needed.
The secondary power switch makes it easy to turn the SX1 on and off when
stowed away under the desk or out of reach. When the switch box is connected to
the connector, it can be used as a power button. The power button on the SX1 can
be used simultaneously even if the switch box is connected.
10. If using other devices, please connect them to the appropriate
connectors.
11. Plug the power cord into the power connector.
If the power cord is connected to a power supply wall socket, regardless of ON or
OFF operation of the power button, eClient SC1/SX1 will starts up.
NOTICE
• Note that the SX1 also starts up whenever electric power is intercepted from
power failure or master power shutdown, and power supply is restored after
that.
WARNING
Use the enclosed power cord and connect to the standard
power outlet of your country.
Be sure to remain within the rated voltage of the power cord.
Not doing so may result in fire or electric shock.
The equipment must be connected to a grounded main
outlet.
Not doing so may result in fire or electric shock.
NOTE
• The screen, which SX1 can display is as follows.
Analog Output Digital Output
16 bbp 16 bbp640 x 480 @60 Hz
32 bbp
640 x 480 @60 Hz
32 bbp
16 bbp 16 bbp800 x 600 @60 Hz
32 bbp
800 x 600 @60 Hz
32 bbp
16 bbp 16 bbp1024 x 768 @60 Hz
32 bbp
1024 x 768 @60 Hz
32 bbp
16 bbp 16 bbp1280 x 1024 @60 Hz
32 bbp
1280 x 1024 @60 Hz
32 bbp
14 2. CONNECTION the eClient SX1

3. OPERATION
This chapter shows how to start and end SC1/SX1 operation.
3-1. Adding a Connection name
When using the RDP protocol
1. Turn on the SX1.
2. The Desktop screen will be displayed.
3. Star the [Remote Desktop Connection].
Double click the [Remote Desktop Connection] icon to open the [Remote Desktop
Connection] dialog box.
Click [Start]-[Remote Desktop Connection] to open the [Remote Desktop
Connection] dialog box.
Click [Start]-[Program]-[Remote Desktop Connection] to open the [Remote
Desktop Connection] dialog box.
4. The [Remote Desktop Connection] will be displayed.
Enter the name of the computer and click [Options].
3. OPERATION 15

5. Set up connection settings of each setting tab of [Options] with
reference to the setting method of Windows.
6. Name the file name and save it.
(1) Click [Save As] of [Connection settings] of the [General] tab.
(2) Name the file (The example is “RDP1.rdp”.), and save it.
16 3. OPERATION

7. A new icon (The example is “RDP1”) is displayed on the desktop.
If a setup finishes, click [Connect] and log on to the WTS, or click [Close] and end
a setup.
3. OPERATION 17

When using the ICA protocol
1. Turn on the eClient SX1.
2. The Desktop screen will be displayed.
3. Double click the [Citrix Program Neighborhood] icon to open the
Citrix program.
Click [Start]-[Citrix Program Neighborhood] to open the Citrix program.
Click [Start]-[Program]-[Citrix]-[MetaFrame Access Clients]-[Program
Neighborhood] to open the Citrix program.
4. The [Citrix Program Neighborhood] will be displayed.
Double click the [Add ICA Connection].
18 3. OPERATION

5. “Add New ICA Connection” Wizard is displayed.
Set up the SX1 according to the directions of the displayed dialog box.
6. The last page of the wizard is displayed and click [Finish], a new
icon (The example is “ICA1”) is added in the “Citrix Program
Neighborhood-Custom ICA Connections” dialog box.
7. If a setup finishes, click [Connect] and log on to the WTS, or click
[Close] and end a setup.
3. OPERATION 19

3-2. Logging on or off the WTS
Logging on to the WTS
1. Turn on the SX1.
2. The Desktop screen will be displayed.
When using the RDP protocol, proceed to step 3, and when using the ICA
protocol, proceed to step 4.
3. When using the RDP protocol
In case the connection icon exists on the desktop
(1) Double click the connection icon (The example below is “RDP1”.).
In case the connection name doesn’t exist on the desktop
20 3. OPERATION