ekwb EK-Quantum Kinetic FLT D5/DDC Body D-RGB User manual

INSTALLATION MANUAL
EKQuantum
Kinetic FLT D5/DDC Body D-RGB

- 2 -
There are many ways to install your EK-Quantum Volume/Kinetic FLT
D5/DDC Body as it utilizes a standard fan mounting hole pattern with
15mm spacing, the same as all EK radiators. The mounting holes have
standard M4 threads with maximum engagement of 10mm. Use of
longer screws or screws with incorrect threads such as those intended
for fans or radiators may damage your product!
Before you start using this product please follow these basic guidelines:
Please carefully read the manual before beginning with the
installation process!
The EK fittings require only a small amount of force to screw
them firmly in place since the liquid seal is ensured by the
rubber o-ring gaskets.
The use of corrosion inhibiting coolants is always recommended
for any liquid cooling system. EKWB recommends any of the
EK-Cryofuel for worry-free usage.

- 3 -
TABLE OF CONTENT
D5 PUMP VERSION 4
ATTACHING THE D5 PUMP ON TO THE RESERVOIR 4
DDC PUMP VERSION 5
ATTACHING THE DDC PUMP ON TO THE RESERVOIR 5
CONNECTING THE D-RGB LED STRIP 6
TESTING THE LOOP 7
SUPPORT AND SERVICE 8
SOCIAL MEDIA 8

- 4 -
ATTACHING THE D5 PUMP ON TO THE RES
ERVOIR
STEP 1:
Remove the preinstalled Pump Holder using 2.5mm Allen Key. Store
the screws and pump holder for later use.
STEP 1
D5 PUMP VERSION
STEP 2:
Make sure that the gasket( o- ring) is placed into the groove.
STEP 2
M4X20
DIN7984
Screw
Pump
holder
52 x 3 Gasket

- 5 -
DDC PUMP VERSION
ATTACHING THE DDC PUMP ON TO THE
RESERVOIR
STEP 1
Remove the preinstalled Pump Holder and screws using 2.5mm
Allen Key. Store the pump holder for later use.
STEP 3
Carefully attach the D5 Pump and Pump Holder(as shown on the
photo). After that, secure all the parts together with M4X20 DIN
7984 Screws. Tighten the screws using enclosed 2.5mm Allen Key.
STEP 3
M4X20
DIN7984
Screw
D5 Pump
holder
STEP 1
M4X20
DIN7984
Screw
Pump
holder

- 6 -
STEP 2
Carefully attach the DDC pump and make sure that gasket (46x2.5) is
placed correctly. Sealing gasket is included in additional bag. Secure
the pump with four (4) M4 X 25 7984DIN screws (see sample photo).
Tighten the screws using enclosed 2.5mm Allen Key.
STEP 2
CONNECTING THE D-RGB LED STRIP
Plug the 3-pin connector from the water block’s D-RGB LED light in
the D-RGB HEADER on the motherboard. The LED will work if the pin
layout on the header is as follows: +5V, Digital.
Please ensure that the arrow indicated on the connector is
plugged into the +5V line as indicated on your motherboard.
Failure to do so will damage your motherboard or LED strip.
D-RGB Header
RGB Header
M4 X 25
DIN7984 Screw
DDC
Pump

- 7 -
TESTING THE LOOP
To make sure the installation of EK components was successful, we
recommend you perform a leak test for 24 hours.
When your loop is complete and filled with coolant, connect the
pump to a PSU outside of your system. Do not connect power to
any of the other components. Turn on the PSU and let the pump
run continuously. It is normal for the coolant level to drop during this
process as air collects in the reservoir.
Inspect all parts of the loop, and in the eventuality that coolant leaks,
fix the issue and repeat the testing process. Ensure that all hardware is
dry before the system is powered on in order to prevent any damage.

For assistance please contact:
http://support.ekwb.com/
EKWB d.o.o.
Pod lipami 18
1218 Komenda
Slovenia - EU
EKWaterBlocks
@EKWaterBlocks
ekwaterblocks
ekwaterblocks
EKWBofficial
SUPPORT AND SERVICE
SOCIAL MEDIA