ekwb EK-Quantum Momentum2 ROG Strix Z690-I Gaming D-RGB -... User manual

USER GUIDE
EK-Quantum
Momentum2ROG Strix X670E-I D-RGB
MONOBLOCK

Please note the installation of the product is intended to be undertaken
by an adequately trained and experienced person. You are installing the
product at your own risk. If you are not properly trained or experienced or
feel unsure about the installation procedure, please refrain from installing
the product yourself and contact our tech support for assistance. We
disclaim our liability for any damages to the product as well as incidental,
consequential, or indirect damages incurred due to improper or
inappropriate installation.
Before you start using this product, please follow these basic guidelines:
Please carefully read the manual before beginning the
installation process.
The EK Fittings require only a small amount of force to screw
them firmly in place since the liquid seal is ensured by the
rubber O-ring gaskets.
The use of corrosion-inhibiting coolants is always recommended
for liquid cooling systems, and mandatory for nickel-plated
water blocks.
Do not use pure distilled water! For best results, EK recommends
the use of EK-Cryo Fuel coolants.
Make sure to thoroughly bleed air out of your water block, or
you will not reach optimal performance

- 3 -
TABLE OF CONTENTS
BOX CONTENTS 4
WATER BLOCK DIMENSIONS 5
TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS 6
PREPARING THE MOTHERBOARD 7
CUTTING AND PLACING THERMAL PADS 8
INSTALLING THE WATER BLOCK 9
FITTINGS AND TUBING 11
CONNECTING THE D-RGB LED STRIP 12
TESTING THE LOOP 12
WARRANTY 13
SUPPORT AND SERVICE 14
SOCIAL MEDIA 14

- 4 -
BOX CONTENTS
Velocity2Mounting Screw AM5 (Ni) (1 pc)
EK-Quantum Momentum2ROG Strix X670E-I D-RGB - Plexi
Allen Key 2 mm (1 pc)Allen Key 2.5 mm (1 pc)
Tx7 L-Shaped Wrench (1 pc)
Thermal grease (1 pc)
Thermal Pad F 1.0 mm (1 pc)
(3830046996732)
120 mm
16 mm

- 5 -
WATER BLOCK DIMENSIONS
13 mm
89 mm
70 mm
98 mm
122 mm
23 mm

- 6 -
TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS
Technical Specification:
Dimensions (L x H x W): 89 x 121.5 x 34 mm
D-RGB cable length: 50 cm
D-RGB LED count: 17
D-RGB connector standard 3-pin (+5V, Data, Blocked, Ground
Position EAN Description Quantity
1106257 Mid plate (Nickel) 1
2105915 Coldplate (Nickel) 1
3105901 Jet Plate AM5 (Metal) 1
4104773 Coldplate OR 53 x 2.5 mm 1
5104686 Screw M4 x 14 DIN7991 4
6106260 TOP Plate (Plexi) 1
7106037 Mounting Screw AM5 (Nickel) 4
8100747 Spring M3 x 10 mm 8 kg 4
98252 Screw M3 x 10 DIN7991 8
10 103007 LED Strip 1
11 100663 EK Badge 1
12 104444 Mylar sticker 1
13 104774 OR 8 x 1.5 1
14 106261 Standout (Acetal) 1
15 5131 OR 100 x 1.5 1
16 5163 OR 18 x 1.5 1
9
5
12
11
7
3
14
10
8
16
13
15
4
1
2
6

- 7 -
PREPARING THE MOTHERBOARD
STEP 1
IIf already installed, please remove the motherboard from your
computer and place it on an even surface.
STEP 2
Using a Philips head screwdriver remove the four UNC 6-32 screws
securing the original plastic hold-down clamps around the socket
as shown in the illustration. Remove the original AMD® backplate
and the hold-down clamps and store them away.
STEP 3
Cleaning the CPU: Wipe the IHS clean using a non-abrasive cloth or
Q-tip as shown in the illustration.
STEP 3
UNC 6-32 SCREW
IHS
NON-ABRASIVE
CLOTH
HOLD-DOWN
CLAMPS
STEP 2

- 8 -
CUTTING AND PLACING THERMAL PADS
STEP 1
EK-Quantum Momentum2ROG Strix X670E-I D-RGB B water block
comes with a thermal pad that has to be cut into smaller pieces to
cover the area.
Please remove the protective foil from both sides of the
thermal pads prior to installation!
Replacement thermal pads:
Thermal Pad F 1.0 mm – (120 x 16 mm) EAN: 3830046996732
For this step, you will need:
Scissors
STEP 1
Thermal Pad F – 1.0 mm (120 x 16 mm)
120 mm
16 mm
1 mm
Thermal Pad - 120 x 16 x 1.0 mm
F1

- 9 -
STEP 2
STEP 2
Applying thermal compound: Apply the enclosed thermal grease
(thermal compound) on the CPU heat spreader – IHS – as shown in
the image. The layer of the thermal compound must be thin and even
in thickness over the entire surface of the IHS.
The excessive or uneven application of thermal grease
may lead to poor performance!
Thermal Grease
For this step, you will need:
STEP 1
Before placing the water block, removing the protective foil from the
backside is mandatory.
STEP 1
INSTALLING THE WATER BLOCK
PROTECTIVE
STICKER

- 10 -
WATER BLOCK
MOUNTING SCREW (4x)
STEP 2
STEP 2
Position the CPU Water Block onto the Motherboard. Make sure to
align the holes (as shown in the picture).
Before placing the water block, it is mandatory to remove
the protective foil from the backside.
Make sure to double-check the layer of the Thermal Grease
before placing the water block onto the motherboard.
STEP 3
Secure the water block from the backside of the motherboard using
the included Tx7 L-Shaped wrench.
Tighten the mounting screws in an anti-clockwise direction. Start
fastening the screws in a cross pattern. Do not tighten fully until all of
the screws are partially screwed in.
The Tx7 L-Shaped wrench must be used in a standing position!
Otherwise, the mounting screws may crack during tightening!
STEP 3
Tx7 L-Shaped wrench
For this step, you will need: