ekwb EK-FC470 GTX Manual

All disclosures, notices and warranty conditions are being written on the back of the box. Released on 13th of April, 2010.
Installation and mounting manual for EK-FC470 GTX water block
This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability
whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwaterblocks.com for updates.
Before installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.
The barb hose fittings require only a small amount of force to screw them in; otherwise the high flow fittings might break. These fittings do not need to be tightened with much force because the
liquid seal is made using o-rings.
STEP 1: GENERAL INFORMATION. Sample picture of NVidia GeForce 470 GTX PCB design
STEP 2: PREPARING YOUR GRAPHIC
CARD.
1. REMOVING STOCK COOLER: Remove
encircled screws on the bracket:
STEP 2 cont.: PREPARING YOUR GRAPHIC CARD
1 cont.. REMOVING STOCK COOLER. Remove all encircled screws. All heat sink assembly
screws and backplate should be removed. There are 16 screws on the back of the graphic
card.
2. CLEANING THE PCB. Carefully detach the original heat sink after removing all
fasteners securing it to the board and bracket. Wipe off the remains (by using
non–abrasive cloth or Q-tip, as shown on sample photo) of the original thermal
compound until the components and circuit board are completely clean. EKWB
does not recommend using any liquids for removing paste.
3. APPLYING THERMAL COMPOUND
Apply thermal compound: lightly coat the GPU with for example Arctic Cooling MX2 ™ or
MX3 ™ thermal compound. Follow this link:
http://www.arctic-cooling.com/catalog/images/install_mx2_retail.pdf for detailed
instructions. EKWB recommends to apply thermal grease in cross form for best performance
(see sample picture).
4. CUTTING THERMAL PADS. Your block comes with thermal pads, which have to
be placed on chips (PLEASE REMOVE FOIL ON BOTH SIDES OF THERMAL PADS
PRIOR TO INSTALLATION. WARNING: DIMENSION BELLOW ARE SCALED.) All
thermal pads are 1mm thick. Thermal pads #1 need to be cut to 4 pieces for
RAM modules.
STEP 3: INSTALLING WATER BLOCK
1. PLACING THERMAL PADS ON PCB. Place thermal pads on chips so that numbers
on chips match size of thermal pads. Thermal pad number 1 & 2 will have to be cut
by user to match all small mosfet chips (EKWB made sure users have more than
enough pads to cover all surfaces that need to be covered to make block fully
function). You can also use small drop of thermal grease on chips to make thermal
pads more adhesive.
2. PLACING GPU REINFORCE PLATE ON PCB. Place metal reinforcer and
reinforce washer on PCB as shown on picture below and screw it in with
enclosed M3x4 screws. Make sure you use fasten screws equally and do
not use too much force.
2
1
1
1
1
1
1
1
1
1
1
Orientation
of reinforce
is important!
2
1 1 1 1
1 1 1 1
1 1 1 1
1
1
2
Washer

All disclosures, notices and warranty conditions are being written on the back of the box. Released on 13th of April, 2010.
3. PLACING STANDOFFS ON BLOCK. Standoffs (thickness 3,9mm) are obligatory to
make this block fully functional and safe mounting. Please use small amount of
thermal grease on standoffs and glue them so they are concentric with mounting
holes. Once they are stuck to block be careful not to move them.
4. ATTACHING BLOCK TO GRAPHIC CARD. By using Philips screwdriver screw in
enclosed M3x8 screws. EKWB recommends start screwing the screws around the
GPU core and continue outwards.
STEP 4: CHECKING FOR CONTACTS
Temporarily r emove the water block to check for uniform surface contact between the block and the components. Note the pattern of contact on a piece of paper. Then repeat
substeps in previous section to reattach the block. In case you can’t get good contact, please check again your thermal pad thickness our contact our support service.
STEP 5: POSITIONING FITTINGS
Please use spacer only on copper base if you use fitting with G1/4 thread longer than 5mm (see sample picture). Screw in the fittings and plugs (please use spacers only on
copper base for fittings). Use 6mm Allen key to screw in and tighten new EK-Plug G1/4. Attach the liquid cooling tubes and connect the water-block(s) into the cooling circuit.
EKWB recommends using high flow fittings with the EK-FC 470 GTX series water blocks. To ensure that the tubes are securely attached to the barb/fittings, please use hose
clamps or an appropriate substitute. The use of an algaecide is always recommended for any liquid cooling system.
You can use any hole as an inlet/outlet hole.
STEP 6: INSERTING CARD IN YOUR PC CASE
Carefully lift your card with installed block and insert it in your PC case. Please bear in mind that your card suddenly withstands extra weight thus again be very careful not to
bend it or cause any other unneeded moves that might damage your card or block during installation.
REQUIRED TOOLS AND MOUNTING SCREWS:
scissors philips screwdriver 10 x screws M3x8 DIN7985 4 x M3x4 DIN7985
Fitting
Gasket/O-ring
G1/4
Spacer
Plug
Use 10 screws M3x8
Plug
6mm Allen key