ekwb EK-Vector Radeon VII Backplate User manual

INSTALLATION MANUAL
EK-Vector Radeon VII Backplate
BACKPLATE

- 2 -
This product is intended for installation only by expert users. Please
consult with a qualified technician for installation. Improper installation
may result in damage to your equipment. EK Water Blocks assumes no
liability whatsoever, expressed or implied, for the use of these products,
nor their installation. The following instructions are subject to change
without notice. Please visit our web site at www.ekwb.com for updates.
Before installation of this product please read important notice,
disclosure and warranty conditions printed on the back of the box.
Before you start using this product please follow these basic
guidelines:
Please carefully read the manual thoroughly before beginning
with the installation process!
Please remove your graphics card from the computer to assure
safest mounting process in order to prevent any possible
damages to your GPU and/or graphics card circuit board (PCB).
This product is anticipated to be used exclusively with EK-
Vector Radeon VII GPU blocks and has not been tested with
any factory or aftermarket heatsinks and water blocks. EK does
not provide any assistance or support in the latter application.

- 3 -
TABLE OF CONTENT
INSTALLING THE BACKPLATE 4
IMPORTANT DISCLOSURES 6
REQUIRED TOOLS 6
SUPPORT AND SERVICE 7
SOCIAL MEDIA 7

- 4 -
INSTALLING THE BACKPLATE
STEP 1
PREPARING YOUR GRAPHICS CARD
EK-Vector Radeon VII Backplate is very simple to install, first complete
the installation of your EK-Vector Radeon VII Water Block according
to its installation manual. Using a Phillips head screwdriver remove
the 7 screws and their PVC washers which are marked below.
STEP 1
1
2
2
STEP 2
CUTTING THERMAL PADS
Your backplate is supplied with thermals pads that need to be cut into
smaller pieces in order to cover all VRM components. PLEASE REMOVE
THE PROTECTIVE STICKER FROM BOTH SIDES OF THE TERMINAL
PADS PRIOR TO INSTALLATION.
Replacement thermal pads:
1. Thermal PAD F 1.0mm - (120x16mm) - (EAN: 3830046996732)
2. Thermal PAD F 1.5mm - (120x16mm) - (EAN: 3830046996749)
STEP 2

- 5 -
STEP 3
PLACING THERMAL PADS
Once cut to size the thermal pads should be applied to the backplate as
illustrated below. EK made sure to provide customers with more than
adequate quantity of thermal pads to complete this step.
STEP 4
ATTACHING THE BACKPLATE
Place the backplate onto the PCB aligning all of the holes. Position an
M2.5x7 AX1 screw in each of the seven (7) mounting holes marked below
and then tighten them evenly using a Phillips head screwdriver. Do not use
excessive screwing force.
1
1
1+2
2
2
2
2
STEP 4
STEP 3

- 6 -
IMPORTANT DISCLOSURES
VERY IMPORTANT NOTICE
Once the installation is completed, it is a recommended practice to
test the cooling circuit for leaks prior to powering up the computer.
We recommend a 24 hour leak test prior to powering up the
computer. Do not test the water block using city water pressure. This
will rupture the top of the housing and render the block unusable
(and will void your warranty). While all efforts have been made to
provide the most comprehensive tutorial possible, EK Water Blocks
assumes no liability expressed or implied for any consequential
damage(s) occurring to your equipment as a result of using EK Water
Blocks cooling products, either due to errors or omissions on our
part in the above instructions, or due to failure or defect in the EK
Water Blocks cooling products.
WARRANTY
Our products are warranted against defects in materials or
workmanship for a period of 24 months beginning from the date of
delivery to the final user. During this period, products will be repaired
or have parts replaced at our discretion provided that: (I) the product
is returned to the agent from whom it was purchased; (II) the product
has been purchased by an end user and has not used for commercial
purposes; (III) the product has not been misused, handled carelessly,
or used in a manner other than in accordance with the instructions
provided describing its installation and proper use. This warranty does
not confer rights other than those expressly set out above and does
not cover any claims for consequential loss or damage. This warranty
is offered as an extra benefit and does not affect your statutory rights
as a consumer. This warranty is voided if the product comes in contact
with aggressive UV additives or other improper liquids. EK blocks are
sealed with warranty void circular label, which proves that the block
has withstood a pressure leak test. Removing it will void leak-free
guarantee and not the guarantee on the product itself. Any other RMA
issues can be reported to EK Support at www.ekwb.com/support for
further analysis.
REQUIRED TOOLS
Phillips-head screwdriver Scissors

For assistance please contact:
http://support.ekwb.com/
EKWB d.o.o.
Pod lipami 18
1218 Komenda
Slovenia - EU
EKWaterBlocks
@EKWaterBlocks
ekwaterblocks
ekwaterblocks
EKWBofficial
SUPPORT AND SERVICE
SOCIAL MEDIA