Elan TS2 User manual

Installation Manual
TS2
Film Interactive Touchpad
INSTALLATION MANUAL

ELAN HOME SYSTEMS TS2 INSTALLATION MANUAL
© ELAN Home Systems 2010 |All rights reserved.
Page 1
Preface
Purpose of this Manual
This manual provides step-by-step installation instructions and connection examples, along with basic user information for
installation and ongoing use of the TS2. This manual is written for the installer of this equipment.
Organization
The following information is contained in this manual.
TS2 Introduction Provides an introduction to ELAN Home Systems’ TS2 , along with system features to include Front
and Rear panel controls, indicators and connections, along with a short description of each.
TS2 System Design and
Installation
Provides a system design application overview and installation requirements for the TS2.
TS2 System Connections Provides a description of the TS2 system connections and direct connections from the TS2 to other
components.
TS2 Setup and Programming Provides directions for enabling / disabling TS2 features and initial TS2 incorporation into the system.
TS2 Display Overview Provides information on the display screens and their functions for the Home Page and sub-system
display and control.
Troubleshooting Provides troubleshooting tables to help fix common problems that may be encountered when
installing the TS2.
Specifications Provides equipment specifications for the TS2.

ELAN HOME SYSTEMS TS2 INSTALLATION MANUAL
© ELAN Home Systems 2010 |All rights reserved.
Page 2
Table of Contents
Preface ............................................................................................... 1
Purpose of this Manual.................................................................................................1
Organization .................................................................................................................1
Chapter 1: Introduction ............................................................4
Film Interactive Technology..........................................................................................4
The ELAN Story ............................................................................................................5
TS2 Features......................................................................................... 6
TS2 Controls and Display .......................................................................... 7
Front Panel Layout .......................................................................................................7
Front Panel Hardware ...................................................................................................8
TS2 Rear Panel Connections ...................................................................... 9
Chapter 2: System Design and Installation................................... 10
Planning............................................................................................ 10
Installation......................................................................................... 10
Pre-Wire............................................................................................ 10
Rough-In............................................................................................ 11
Mounting Height .................................................................................. 11
Changing Films.................................................................................... 12
Connectors/Pinout ................................................................................ 14
System Port RJ-45 Connector....................................................................................14
Local IR Interface Port................................................................................................15
IR-Emitter Out ............................................................................................................15
IR Receiver In.............................................................................................................16
Local Sense Input.......................................................................................................17
Chapter 3: System Connections ................................................ 18
HCxx Series System Controllers ................................................................ 18
TS2 to PPVN Connections ..........................................................................................18
Legacy Home Controllers ........................................................................ 19
Connection Method #1 ...............................................................................................19
Connection Method #2 ...............................................................................................20

ELAN HOME SYSTEMS TS2 INSTALLATION MANUAL
© ELAN Home Systems 2010 |All rights reserved.
Page 3
Chapter 4: Setup and Programming ........................................... 21
The Service Menu................................................................................. 21
Initial TS2 Integration .................................................................................................22
Speaker ......................................................................................................................24
IR Sensor ...................................................................................................................25
Light Sensor Disable ..................................................................................................26
Light Sensor Enable....................................................................................................27
OLED Info...................................................................................................................29
Chapter 5: Display Screens ..................................................... 32
Home Pages ....................................................................................... 33
Media Page ........................................................................................ 35
Source Page Samples.................................................................................................37
Light Page.......................................................................................... 39
Security Page...................................................................................... 41
Climate Page ...................................................................................... 43
Troubleshooting ................................................................................... 46
Specifications ..................................................................................... 47
Warranty…………………………………………………………………..…….Last Page

ELAN HOME SYSTEMS TS2 INSTALLATION MANUAL
© ELAN Home Systems 2010 |All rights reserved.
Page 4
Chapter 1: Introduction
TS2 Film Interactive Touchpad (FIT) is a double-gang, in-wall system controller that uses a
touch film in lieu of hard buttons to perform all functions normally associated with a
keypad. Source and system control icons and function names are printed on
interchangeable backlit film transparencies. Each icon or function name corresponds to an
active “hot spot” that issues a control command and gives both audible and visual
confirmation to the user when pressed.
The TS2 is for use with ELAN Home Controllers running Core Module Software 5.0 or later
and is not interchangeable with the Olé2XL.
The touchpad features a 2" color OLED to provide source, sub-system and programming
feedback to the user.
Programming for the TS2 resides in the Home Controller and is accomplished with ELAN’s
Configuration Software.
Film Interactive Technology
The TS2 utilizes a polyester plastic film suspended over a glass panel, which is placed over
a changeable backlit film. Depressing the polyester film with a finger allows the film to
touch the glass panel underneath, generating a location signal that is read by the
electronics.
Items in Package:
•TS2 Touchpad
•White Trim Plate
•Black Film Overlay
•White Film Overlay
•Quick Install Guide
•User’s Guide
•Mounting Screws (4)

ELAN HOME SYSTEMS TS2 INSTALLATION MANUAL
© ELAN Home Systems 2010 |All rights reserved.
Page 5
The ELAN Story
Located in Lexington, KY, USA, ELAN Home Systems has designed innovative multi-room
audio/video systems since 1989. ELAN systems were the first to integrate music, intercom
and TV distribution features that used the homeowner’s stereos, televisions and telephones
to create the whole-house entertainment experience. These Systems allow people to move
from room to room, controlling centrally located equipment with ease.
ELAN’s product line includes:
•Power Amplifiers
•Multi-Zone Pre-Amps
•Intelligent Keypads
•In-Wall LCD Color Touch Panels
•Wireless LCD Color Touch Panels
•Film Interactive Touchpads
•In-Wall and In-Ceiling Speakers
•Outdoor Speakers
•Home Automation Controllers
•A/V Controllers
•Volume Controls
•Telephone-Based Intercom Controllers
•Video Switchers
•Digital Music & DVD Management Systems
•Satellite Radios
•Accessories for Home Systems Installation

ELAN HOME SYSTEMS TS2 INSTALLATION MANUAL
© ELAN Home Systems 2010 |All rights reserved.
Page 6
TS2 Features
Full touchpad design, no hard buttons
2” color OLED (Organic LED) Display
Brightness-adjusting light sensor (can be disabled)
Audible ‘click’ to indicate a button press (can be disabled)
ELAN Configuration Software programming
Compatible with all current ELAN Home Controllers running 5.0 software or higher
System and sub-system feedback
Built-in IR receiver (can be disabled)
Connectivity for Remote IR Receiver
Sense Trigger Input (future use)
Fits in a double-gang electrical box
THE TS2 SUPPORTS THE FOLLOWING FEATURES:
Basic Time & Weather information: The home interface displays time and basic weather
information. Optionally, additional pages for weather forecast and/or house modes can be
enabled.
Lighting Control: The lighting interface displays a custom lighting keypad for 2-way control
of scenes or lighting loads.
Security Control: The security interface displays status of one partition and a keypad to
arm/disarm that partition.
Climate Control: The climate interface displays status of one climate zone and provides
mode, fan, and set point adjustments.
Media Control: The media interface displays status of one media zone and provides
controls for power, source, volume, mute, and basic source control. The interface provides
meta data feedback (no cover art at this time) for supported two way devices or
customizable single or multi-page interfaces for one way device control.

ELAN HOME SYSTEMS TS2 INSTALLATION MANUAL
© ELAN Home Systems 2010 |All rights reserved.
Page 7
TS2 Controls and Display
Front Panel Layout
Figure 1-1:
TS2 Front Panel Controls
and Display

ELAN HOME SYSTEMS TS2 INSTALLATION MANUAL
© ELAN Home Systems 2010 |All rights reserved.
Page 8
Front Panel Hardware
1) Mounting Screws (x4)
2) Film Hinge (x2)
3) Film Screw (x2) 6) Mini USB Download Port
(Future firmware upgrades)
5) Light Sensor
4) Service Menu Button
Figure 1-2:
TS2 Front Panel Hardware

ELAN HOME SYSTEMS TS2 INSTALLATION MANUAL
© ELAN Home Systems 2010 |All rights reserved.
Page 9
TS2 Rear Panel Connections
Figure 1-3:
TS2 Rear Panel Connections
1) System Port RJ-45 Jack 2) Local IR Interface
1 2

ELAN HOME SYSTEMS TS2 INSTALLATION MANUAL
© ELAN Home Systems 2010 |All rights reserved.
Page 10
Chapter 2: System Design and Installation
Planning
Before installing the TS2, it is essential to have a detailed and accurate system design. Talk
with the homeowner to make sure all expectations and design goals are explored. The first
step to a good design is to map the system. It is advisable to mark up a copy of the house
floor plan with speaker, touchpad, touch panel, volume control, and equipment locations
etc. Make sure that all locations are decided upon before pre-wiring commences so that all
necessary wiring and installation hardware is in place.
It is essential that ALL system components are accounted for prior to the pre-wire stage.
After establishing design goals with the homeowner, make a detailed list of all components.
Include source equipment, keypads, touch panels, volume controls, amplifiers,
communications gear, etc. Gather up any IR remote controls that may be necessary for
final programming, or ensure that the IR codes for all equipment to be installed are
available in the ELAN Configuration Software.
Installation
TS2 is designed to fit into a standard 32 cu. in. two-gang electrical box. Consult local
building codes for specifics in your geographic area. The TS2 is not compatible with some
two-gang mud rings. ELAN recommends test fitting a unit prior to installation.
Pre-Wire
Each TS2 Touchpad has an RJ45 jack on the back to allow for easy connection. Run Cat-5
wire from the central equipment location (head-end) to the location where each Touchpad
will be installed.
Note: Maximum wire run is 1000 feet. The total of wire runs to all TS2s must not
exceed 2000 feet. In the event you need to exceed that limit, VIA!Net Repeaters must
be installed on the longest wire runs.

ELAN HOME SYSTEMS TS2 INSTALLATION MANUAL
© ELAN Home Systems 2010 |All rights reserved.
Page 11
Rough-In
Roughing-in the TS2 requires careful attention to the design plan made previously. See
System Design & Applications for a list of things to factor in to specific mounting locations
before deciding exactly where to place the unit. In order to avoid Electro-Magnetic
Interference (EMI), do not mount Touchpads close to light dimmers. Leave at least one
stud-bay open between Touchpads and dimmers (leave more space if multiple dimmers are
present). Avoid installing TS2 Touchpads in areas that will receive direct sunlight. Sunlight
can flood the IR receiver and make the system inoperative.
Do not mount Touchpads outdoors! Corrosion will damage them. ELAN does not warrant
TS2 Touchpads for outdoor use.
Mounting Height
The TS2 has no viewing angle limitations, so mounting height should be determined by the
average height of the user. Typical mounting height is 56-60 inches from the floor to the
bottom of the electrical box. This will provide optimum viewing for the largest number of
people.
Figure 2-1:
TS2 Mounting Height

ELAN HOME SYSTEMS TS2 INSTALLATION MANUAL
© ELAN Home Systems 2010 |All rights reserved.
Page 12
Changing Films
To change films:
1. Remove the magnetic wall plate from the front of the unit.
2. Remove the two film screws on the right side of the unit.
3. Use the notch located in the upper right-hand corner to open the
touch screen (45° max.).
4. Remove the existing film.
5. Place the new film into the holder of the transparent touch
screen making sure of the proper orientation.
6. Close the touch screen.
7. Replace the two film screws.
8. Replace the wall plate.
Figure 2-2:
Film Screw Location
Screw
Screw

ELAN HOME SYSTEMS TS2 INSTALLATION MANUAL
© ELAN Home Systems 2010 |All rights reserved.
Page 13
Touch Screen
Film
Place Film in
Holder on
Touch Screen
Figure 2-3:
Changing Films

ELAN HOME SYSTEMS TS2 INSTALLATION MANUAL
© ELAN Home Systems 2010 |All rights reserved.
Page 14
Connectors/Pinout
The TS2 has a System RJ-45 connector and a five pin Interface Port connector which each
perform specific functions. All applications will use the RJ-45 connector, while certain
situations will require the use of the Interface Port.
System Port RJ-45 Connector
The System RJ-45 uses the ELAN Standard Pinout configuration shown below and
connects to the PPVN precision panel.
TS2 RJ-45 Connector
1 Blue 2 White/Blue 3 Orange 4 White/Orange 5 Green 6 White/Green 7 Brown 8 White/Brown
1 Blue
2 White/Blue
3 Orange
4 White/Orange
5 Green
6 White/Green
7 Brown
8 White/Brown
Figure 2-4:
TS2 RJ-45 Pinout

ELAN HOME SYSTEMS TS2 INSTALLATION MANUAL
© ELAN Home Systems 2010 |All rights reserved.
Page 15
Local IR Interface Port
Use this connector when utilizing the TS2’s Local Control features such as Local source IR
routing, Local IR Sensors, or Sense-enabled automated sequences (future use.)
IR-Emitter Out
The Local IR-EMITTER OUT is typically used to route IR to devices that are not part of the
main system, such as a receiver or DVD player located within the same room as the
touchpad. IR is routed to an emitter or IR distribution block connected to the Local IR
Output.
For example: You have local gear in a cabinet with closed doors; simply point the remote
at the IR receiver in the TS2.
Any IR signal that is received from the front IR-RECEIVER is sent out both the Local IR-
EMITTER OUT and the System IR Output. Pressing a button on the TS2 will not issue IR
commands from these outputs.
Connect IR-EMITTER OUT and -GROUND as shown below.
Figure 2-5:
Interface Port IR Out
The connection labeled “+12 VOLTS OUT”
is a Voltage Output.
DO NOT CONNECT A POWER SUPPLY TO
THIS CONNECTION

ELAN HOME SYSTEMS TS2 INSTALLATION MANUAL
© ELAN Home Systems 2010 |All rights reserved.
Page 16
IR Receiver In
The Local IR-RECEIVER IN is typically used to connect an external IR sensor to the
touchpad. Typical applications include a plasma-friendly IR sensor (ELAN IRS8EP, for
example) placed near a TV, or an auxiliary IR sensor placed in an area more convenient
than the location of the touchpad. IR signals that are received by the IR Input are sent out
both the Local IR-EMITTER OUT and the System IR Output.
Connect IR-RECEIVER IN, -GROUND and +12VOLTS OUT as shown below.
Note: In certain cases, the TS2’s built-in IR sensor can be flooded with plasma TV
interference or other ambient light interference. In this case, connect a plasma-friendly IR
sensor (ELAN IRS8EP, for example) to the Local IR Input and disable the built-in IR sensor
using the Service Menu
(See SERVICE MENU on page 25.)
Figure 2-6:
Interface Port IR
Receiver

ELAN HOME SYSTEMS TS2 INSTALLATION MANUAL
© ELAN Home Systems 2010 |All rights reserved.
Page 17
Local Sense Input
(Future applications)
The LOCAL SENSE IN port allows a contact-closure to trigger IR or RS-232 sequences
programmed in the ELAN Configuration Software. Use a motion sensor to activate a
contact-closure and cause automated actions such as system power on, drapes closed,
and lights dimmed, for example.
Connect LOCAL SENSE IN and –GROUND to a contact-closure device as shown below.
Figure 2-7:
Interface Port Local
Sense Input

ELAN HOME SYSTEMS TS2 INSTALLATION MANUAL
© ELAN Home Systems 2010 |All rights reserved.
Page 18
Chapter 3: System Connections
HCxx Series System Controllers
TS2 to PPVN Connections
TS2 connection to any of the ELAN System Controllers (HC12, HC6, etc.) is accomplished
using the PPVN (VIA!NET Precision Panel.) A single Cat5 connects the TS2 to the VIA!NET
punch downs on the back of the PPVN and a Cat5 jumper connects from the front of the
PPVN to the VIA!NET port on the System Controller. The IR output on the front of the
PPVN may be connected to an IR distribution system or to the EXT IR IN of the Home
Controller as shown below.
Each PPVN will accommodate connections for up to four TS2s. PPVNs may be “daisy-
chained” to allow additional TS2s to be incorporated into the system. The TS2s are
powered by a 16V power supply connected to the PPVN. Each PPVN requires its own 16V
power supply.
The TS2 sends VIA!NET messages to the System Controller. The System Controller then
issues the proper commands for the sub-system being controlled.
Figure 3-1:
TS2 to PPVN

ELAN HOME SYSTEMS TS2 INSTALLATION MANUAL
© ELAN Home Systems 2010 |All rights reserved.
Page 19
Legacy Home Controllers
TS2 connection to any of the legacy Home Controllers (HomeBrick, MultiBrick) is
accomplished using the PPVN (VIA!NET Precision Panel) and an SC1. A single Cat5
connects the TS2 to the VIA!NET punch downs on the back of the PPVN and a Cat5 jumper
connects from the front of the PPVN to the VIA!NET port on the SC1.
There are two methods that may be used to connect the RS-232 port of the SC1 to the
HomeBrick or the MultiBrick. Each method will be shown in the following pages.
Each PPVN will accommodate connections for up to four TS2s. PPVNs may be “daisy-
chained” to allow additional TS2s to be incorporated into the system. The TS2s are
powered by a 16V power supply connected to the PPVN. Each PPVN requires its own 16V
power supply. The SC1 will receive its power from the PPVN’s power supply as well.
When using legacy Home Controllers the TS2 sends VIA!NET messages to the SC1 which
then converts them to RS-232 commands and sends them to the Home Controller. The
Home Controller then issues the proper commands for the sub-system being controlled.
Connection Method #1
This method requires the use of RJ45 to DB9 adapter HA-CB-328 (DB9 female to RJ45
female NULL adapter) and the SC1’s DB9 male to RJ45 female adapter to connect the SC1
to the Network Assembly.
1 – ELAN Standard Cat5 Cable
(See page 14 for pinout) 3 – SC1 DB9M to RJ45 Adapter
2 – Ethernet Standard Cat5 Cable 4 – HA-CB-328 DB9F to RJ45 NULL Adapter
Figure 3-2:
TS2 / SC1 / Legacy
Controllers with
DB9 Adapters