Elation ACL PAR 200IP User manual

ACL PAR 200IP™
user manual 
ELATION |
ACL PAR 200IP™
|
user manual

www.elationlighting.com
2ACL PAR 200IP™ User Manual
©2015 ELATION PROFESSIONAL all rights reserved. Information, specifications,
diagrams, images, and instructions herein are subject to change without notice.
ELATION PROFESSIONAL logo and identifying product names and numbers herein
are trademarks of ELATION PROFESSIONAL. Copyright protection claimed includes
all forms and matters of copyrightable materials and information now allowed by
statutory or judicial law or hereinafter granted. Product names used in this
document may be trademarks or registered trademarks of their respective
companies and are hereby acknowledged. All non-ELATION brands and product
names are trademarks or registered trademarks of their respective companies.
ELATION PROFESSIONAL and all affiliated companies hereby disclaim any and all
liabilities for property, equipment, building, and electrical damages, injuries to any
persons, and direct or indirect economic loss associated with the use or reliance of
any information contained within this document, and/or as a result of the improper,
unsafe, insufficient and negligent assembly, installation, rigging, and operation of
this product.
Elation Professional USA | 6122 S. Eastern Ave. | Los Angeles, CA. 90040
323-582-3322 |323-832-9142 fax | www.elationlighting.com |[e-mail]
Elation Professional B.V. | Junostraat 2 | 6468 EW Kerkrade, The Netherlands
[phone] |[phone] fax |www.elationlighting.eu |[e-mail]
DOCUMENT VERSION
Please check www.elationlighting.com for the latest revision/update of this manual.
Date Document
Version
Software
Version
DMX
Channel Modes Notes
11/04/15 1
≥1U01:V102
≥2U01:V102
4CH1:04 / 4CH2:04 / 6 / 8 / 10
12 / 27 / 28 / 30 / 32 / 35
Initial release.

www.elationlighting.com
3ACL PAR 200IP™ User Manual
CONTENTS
General Information
4
Warranty
7
Safety Instructions
8
General Guidelines
9
Fixture Overview
10
Fixture Installation
11
Fixture Menu
13
DMX Channel Functions And Values
16
Cleaning and Maintenance
21
Technical Specifications
22
Optional Accessories
25

www.elationlighting.com
4ACL PAR 200IP™ User Manual
GENERAL INFORMATION
INTRODUCTION
Congratulations, you have just purchased one of the most innovative and
reliable lighting fixtures on the market today! This fixture has been designed to
perform reliably for years when the guidelines in this booklet are followed. Please
read and understand the instructions in this manual carefully and thoroughly
before attempting to operate this unit. These instructions contain important
information regarding safety during use and maintenance.
IP65 RATED
An IP rated lighting fixture is one, which is commonly installed in outdoor
environments and has been designed with an enclosure that effectively protects
the ingress (entry) of external foreign objects such as dust and water. The
International Protection (IP) rating system is commonly expressed as "IP" (Ingress
Protection) followed by two numbers (i.e. IP65) where the numbers define the
degree of protection. The first digit (Foreign Bodies Protection) indicates the
extent of protection against particles entering the fixture and the second digit
(Water Protection) indicates the extent of protection against water entering the
fixture. An IP65 rated lighting fixture is one, which has been designed and tested
to protect against the ingress of dust (6) and high-pressure water jets from any
direction (5).
MARINE/COASTAL ENVIRONMENT INSTALLATIONS!
Please note although this fixture is IP rated, the fixture is NOT suitable for marine
and/or coastal environment installations. Installing this fixture in a marine and/or
coastal environment may cause corrosion and/or excessive wear to the interior
and/or exterior components of the fixture. Damages and/or performance
issues resulting from installation in a marine and/or coastal environment will void
the manufactures warranty and will NOT be subject to any warranty claims
and/or repairs.
Ensure ALL connections and end caps are properly sealed with a
non-conductive dielectric grease (available at most electrical suppliers) to
prevent water ingress/condensation and/or corrosion.
OPTIONAL CORROSION-RESISTANT COATING
Optional Corrosion-Resistant Coatings may be available for this fixture.
Please consult your Elation Professional sales representative for details.

www.elationlighting.com
5ACL PAR 200IP™ User Manual
UNPACKING
Every fixture has been thoroughly tested and has been shipped in perfect
operating condition. Carefully check the shipping carton for damage that may
have occurred during shipping. If the carton appears to be damaged, carefully
inspect your unit for damage and be sure all accessories necessary to operate
the unit have arrived intact. In the event damage has been found or parts are
missing, please contact our customer support team for further instructions. Please
do not return this unit to your dealer without first contacting customer support at
the number listed below. Please do not discard the shipping carton in the trash.
Please recycle whenever possible.
BOX CONTENTS
Male Edison to IP Female Power Cable 6,6 ft. (2m)
Male 3pin XLR to IP Female DMX Input Cable 3.3 ft (1m)
Female 3pin XLR to IP Male DMX Output Cable 3.3 ft (1m)
Manual & Warranty Card
CUSTOMER SUPPORT
Elation Professional®provides a customer support line, to provide set up help and
to answer any question should you encounter problems during your set up or
initial operation. You may also visit us on the web at www.elationlighting.com for
any comments or suggestions. For service related issue please contact Elation
Professional®.
ELATION SERVICE USA - Monday - Friday 8:00am to 5:00pm PST
Voice: 323-582-3322 Fax: [phone]
E-mail: [email protected]
ELATION SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET
Voice: [phone] Fax: [phone]
E-mail: [email protected]

www.elationlighting.com
6ACL PAR 200IP™ User Manual
WARRANTY REGISTRATION
Please complete and mail in the enclosed warranty card or register online:
http://www.elationlighting.com/Login.aspx to validate your purchase. All
returned service items whether under warranty or not, must be freight pre-paid
and accompany a return authorization (R.A.) number. The R.A. number must be
clearly written on the outside of the return package. A brief description of the
problem as well as the R.A. number must also be written down on a piece of
paper and included in the shipping container. If the unit is under warranty, you
must provide a copy of your proof of purchase invoice. Items returned without a
R.A. number clearly marked on the outside of the package will be refused and
returned at customer’s expense. You may obtain a R.A. number by contacting
customer support.
IMPORTANT NOTICE!
There are no user serviceable parts inside this unit. Do not attempt any repairs
yourself; doing so will void your manufactures warranty. Damages resulting from
modifications to this fixture and/or the disregard of safety and general user
instructions found in this user manual void the manufactures warranty and are
not subject to any warranty claims and/or repairs.

www.elationlighting.com
7ACL PAR 200IP™ User Manual
LIMITED WARRANTY
A. Elation Professional® hereby warrants, to the original purchaser, Elation Professional® products to
be free of manufacturing defects in material and workmanship for a period of two years (730 days),
and Elation Professional® product rechargeable batteries to be free of manufacturing defects in
material and workmanship for a period of six months (180 days), from the original date of purchase.
This warranty excludes discharge lamps and all product accessories. This warranty shall be valid only
if the product is purchased within the United States of America, including possessions and territories. It
is the owner’s responsibility to establish the date and place of purchase by acceptable evidence, at
the time service is sought.
B. For warranty service, send the product only to the Elation Professional® factory. All shipping
charges must be pre-paid. If the requested repairs or service (including parts replacement) are within
the terms of this warranty, Elation Professional® will pay return shipping charges only to a designated
point within the United States. If any product is sent, it must be shipped in its original package and
packaging material. No accessories should be shipped with the product. If any accessories are
shipped with the product, Elation Professional® shall have no liability what so ever for loss and/or or
damage to any such accessories, nor for the safe return thereof.
C. This warranty is void if the product serial number and/or labels are altered or removed; if the
product is modified in any manner which Elation Professional® concludes, after inspection, affects
the reliability of the product; if the product has been repaired or serviced by anyone other than the
Elation Professional® factory unless prior written authorization was issued to purchaser by Elation
Professional®; if the product is damaged because not properly maintained as set forth in the product
instructions, guidelines and/or user manual.
D. This is not a service contract, and this warranty does not include any maintenance, cleaning or
periodic check-up. During the periods as specified above, Elation Professional® will replace
defective parts at its expense, and will absorb all expenses for warranty service and repair labor by
reason of defects in material or workmanship. The sole responsibility of Elation Professional® under
this warranty shall be limited to the repair of the product, or replacement thereof, including parts, at
the sole discretion of Elation Professional®. All products covered by this warranty were manufactured
after January 1, 1990, and PAR 200e identifying marks to that effect.
E. Elation Professional® reserves the right to make changes in design and/or performance
improvements upon its products without any obligation to include these changes in any products
theretofore manufactured.
F. No warranty, whether expressed or implied, is given or made with respect to any accessory
supplied with the products described above. Except to the extent prohibited by applicable law, all
implied warranties made by Elation Professional® in connection with this product, including
warranties of merchantability or fitness, are limited in duration to the warranty periods set forth above.
And no warranties, whether expressed or implied, including warranties of merchantability or fitness,
shall apply to this product after said periods have expired. The consumer’s and/or dealer’s sole
remedy shall be such repair or replacement as is expressly provided above; and under no
circumstances shall Elation Professional® be liable for any loss and/or damage, direct and/or
consequential, arising out of the use of, and/or the inability to use, this product.
G. This warranty is the only written warranty applicable to Elation Professional® products and
supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published.

www.elationlighting.com
8ACL PAR 200IP™ User Manual
SAFETY INSTRUCTIONS
This fixture
is an extremely sophisticated piece of electronic equipment. To
guarantee a smooth operation, it is important to follow the guidelines in this
manual. The manufacturer of this device will not accept responsibility for
damages resulting from the misuse of
this fixture due to the disregard of the
information printed in this manual.
This device falls under PROTECTION CLASS 1
. It’s essential this device be
grounded properly. Only qualified personnel should
perform all electrical
connections.
UNPLUG POWER BEFORE SERVICING FIXTURE!
DO NOT PLUG FIXTURE INTO A DIMMER PACK!
NEVER TOUCH FIXTURE DURING OPERATION, AS IT MAY BE HOT!
NEVER LOOK DIRECTLY INTO THE LIGHT SOURCE!
SENSITIVE PERSONS MAY SUFFER AN EPILEPTIC SHOCK!
For proper operation, follow the Installation guidelines described in this manual. Only qualified
and certified personnel should perform installation of this fixture and only the original rigging parts
(brackets) included with this fixture should be used for installation. Any modifications will void the
original manufactures warranty and increase the risk of damage and/or personal injury.
Never look directly into the light source of this fixture to prevent risk of injury to your retina, which
may induce blindness. Those suffering from EPILEPSY should avoid looking directly into the light
source of this unit at all times.
The fan and air inlets must remain clean and never blocked. Allow approx. 6” (15cm) between
this fixture and other devices or a wall for proper cooling.
Always disconnect from main power source before performing any type of service and/or
cleaning procedure. Only handle the power cord by the plug end, never pull out the plug by
tugging the wire portion of the cord.
Do not operate this fixture if the power cord has become frayed, crimped and/or damaged. If
the power cord is damaged, replace it immediately with a new one of similar power rating.

www.elationlighting.com
9ACL PAR 200IP™ User Manual
GENERAL GUIDELINES
NEVER OPEN THIS FIXTURE WHILE IN USE!
Ensure ALL connections and end caps are properly sealed with a dielectric
grease (available at most electrical suppliers) to prevent water corrosion and/or
electrical short circuit.
During the initial operation of this fixture, a light smoke or smell may emit from the
interior of the fixture. This is a normal process and is caused by excess paint in the
interior of the casing burning off from the heat associated with the lamp and will
decrease gradually over time.
Please make sure there are NO FLAMMABLE MATERIALS close to the fixture while
operating, to prevent any fire hazard.
The fixture must be installed in a location with adequate ventilation, at least 1.5
feet (.5m) from adjacent surfaces. Be sure no air ventilation slots are blocked.
DO NOT attempt installation and/or operation without knowledge how to do so.
DO NOT permit operation by persons who are not qualified to operate this type
of fixture. Most damages are the result of operations by nonprofessionals.
Consistent operational breaks may ensure the fixture will function properly for
many years to come.
DO NOT shake fixture, avoid brute force when installing and/or operating fixture.
Always install the fixture with an appropriate safety cable. When installing the
fixture in a suspended environment, always use mounting hardware that is no less
than M10 x 25 mm, also be sure the hardware is insert in the pre-arranged screw
holes in the bracket of the fixture.
Use the original packaging and materials to transport the fixture in for service.
DO NOT TOUCH the housing bare-hand during its operation. Turn OFF the power
and allow approximately 15 minutes for the fixture to cool down before replacing
or serving.

www.elationlighting.com
10 ACL PAR 200IP™ User Manual
FIXTURE OVERVIEW
1. MODE Button
2. UP Button
3. DOWN Button
4. ENTER Button
5. Power IN
6. DMX IN
7. DMX Out
8. Power OUT
9. Vent

www.elationlighting.com
11 ACL PAR 200IP™ User Manual
FIXTURE INSTALLATION
FLAMMABLE MATERIAL WARNING
Keep fixture at least 5.0 ft (1.5m) away from any
flammable materials, decorations, pyrotechnics, etc.
ELECTRICAL CONNECTIONS
A qualified electrician should be used for all
electrical connections and/or installations.
CAUTIONS
For added protection, mount the fixture in areas outside walking paths, seating
areas, or in areas were unauthorized personnel might reach the fixture.
Ambient operating temperature range for this fixture is 5° to 113°F. (-15° to 45°C)
Do not use the fixture under or above this temperature.
Before mounting the fixture to any surface, make sure the installation area can
hold a minimum point load of 10 times the weight of the fixture.
Fixture installation must always be secured with a secondary safety attachment,
such as an appropriate safety cable.
Never stand directly below the device when mounting, removing or servicing.
Ensure ALL connections and end caps are properly sealed with a dielectric
grease (available at most electrical suppliers) to prevent water corrosion and/or
electrical short circuit.
POWER LINKING
Max number of units that can be power linked is 9 units @110V and 21 units @240V.
CLAMP MOUNTING
The fixture provides an integrated mounting dual bracket / yoke. Make sure to
secure an appropriately rated clamp to the mounting bracket using M10 screws
when mounting this fixture to truss.

www.elationlighting.com
12 ACL PAR 200IP™ User Manual
MOUNTING POINTS
Overhead mounting requires extensive experience, including amongst others
calculating working load limits, installation material being used, and periodic
safety inspection of all installation material and the device. If you lack these
qualifications, do not attempt the installation yourself. Improper installation can
result in bodily injury.
Fixture is fully operational in the specific mounting positions as illustrated below.
SAFETY CABLE
ALWAYS USE A SAFETY CABLE (NOT INCLUDED) WHENEVER INSTALLING THIS FIXTURE IN A
SUSPENDED ENVIRONMENT TO ENSURE THE FIXTURE WILL NOT DROP IF THE CLAMP FAILS.

www.elationlighting.com
13 ACL PAR 200IP™ User Manual
FIXTURE MENU
ON-BOARD SYSTEM MENU
The fixture comes with an easy to navigate system menu. The next section will detail
the functions of each command in the system menu.
LCD MENU CONTROL PANEL
The control panel (see image below) located on back of the fixture allows you to
access the main menu and make all necessary adjustments to the fixture. During
normal operation, pressing MODE button once will access the fixture’s main menu.
Once in the main menu you can navigate through the different functions and
access the sub-menus with the UP and DOWN buttons. Once you reach a field that
requires adjusting, press the ENTER button to activate that field and use the UP and
DOWN buttons to adjust the field. Pressing the ENTER button once more will confirm
your setting. You may exit the main menu at any time without making any
adjustments by pressing the MODE button.
INFORMATION DISPLAYED DURING INITIAL POWER ON
When the fixture is initially powered ON, the display shows the following information:
Fixture Software Version (Greater than or equal to)
Update
Wait...
ELATION
V1.02

www.elationlighting.com
14 ACL PAR 200IP™ User Manual
ELATION© ACL PAR 200IP™
S Y S T E M M E N U
Specifications are subject to change without any prior written notice. Defaults In Bold.
MENU
OPTIONS / VALUES
DESCRIPTION
DMX MODE
ADDR:001 CH:xx
ADDR:001 - 512
4CH1:04, 4CH2:04, CH:06, CH:08, CH:10,
CH:12, CH:27, CH:28, CH:30, CH:32, CH:35
DMX Address Setting
DMX Channel Mode
SLAVE
M O D E
Set Fixture To Slave Mode
AUTO RUN
FQN:xx
FQN:01-99 Set Number Of Times Each AUTO PROGRAM MACRO
Repeats Before Moving To Next Macro.
01.STATIC
-
15.FLOW 1
01.STATIC
CL:RGB FADE00 Select INTERNAL PROGRAM MACRO.
Dim Curve
Standard, Stage, TV, Architec, Theatre
Set Desired Dimming Curve
Pixel Flip STANDARD, Flip 1, Flip 2, Flip 3
Set Starting Pixel LED.
See Pixel Flip Setting Section.
NO DMX Hold, Blackout, Program
Define How Fixture Reacts When NO DMX Signal
Present.
Manual
R000-255 G000-255 B000-255
W000-255 Strobe:000
Set RGBW + Strobe values manually for ALL 7 LEDs.
Macros
01-64 Set Color Macro.
LCD Set
Blackligh 02S-60S [05S]
LCD Display Shutoff Time.
Key Lock OFF, ON
Set Control Display Key Lock Feature.
DispFlas ON, OFF
LCD Display flashes when NO Signal is detected.
Temp
F° , C°
Set temperature to F° / C°
DFSE
OFF, ON
Restore Factory Settings.
Info
TimeInfo
Current 0000
TotalTim 0000
LastClea 0000
TimerPIN XXXX
ClearLas [OFF, ON]
Displays Internal Timers.
Enter PIN [066] To Access Clear Timer Function.
Temp Info
XXX F°
Displays Current Fixture Temperature.
ModelInf
ACL Par
Displays Model Name.
Software ≥1U01V106
≥2U01V104 Displays Software Versions. (Greater Than or Equal To)

www.elationlighting.com
15 ACL PAR 200IP™ User Manual
Dim Curve
Select desired DIMMER MODE (Standard, Stage, TV, Architec, Theatre).
Pixel Flip
Select the desired starting LED and chase direction from one of the following modes below
via UP/DOWN buttons and then press ENTER to confirm. (Default = STANDARD)

www.elationlighting.com
16 ACL PAR 200IP™ User Manual
DMX CHANNEL FUNCTIONS AND VALUES
ELATION© ACL PAR 200IP™
DMX Channel Values / Functions Version 1 (35 DMX Channels)
Specifications are subject to change without any prior written notice.
*Control of LEDs depends on the Pixel Flip setting. | **CH27 Mode does not include channels 4, 5, 6, 22, 23, 24.
DMX CHANNEL MODE VALUE FUNCTION
4CH1:04 4CH2:04 6CH 8CH 10CH 12CH 27CH 28CH 30CH 32CH 35CH 16 BIT CHANNELS
1 1 1 1 1 RED LED - All LEDS [1-7]
0-255 Red (0-Black - 255-100%)
2 2 2 2 2 GREEN LED - All LEDs [1-7]
0-255
Green (0-Black - 255-100%)
3 3 3 3 3
BLUE LED - All LEDs [1-7]
0-255
Blue (0-Black - 255-100%)
4 4 4 4 4
WHITE LED - All LEDs [1-7]
0-255
White (0-Black - 255-100%)
1 1 1 1 1 RED LED - LED [1]
0-255 Red (0-Black - 255-100%)
2 2 2 2 2 GREEN LED - LED [1]
0-255
Green (0-Black - 255-100%)
3 3 3 3 3
BLUE LED - LED [1]
0-255 Blue (0-Black - 255-100%)
4 4 4 4
WHITE LED - LED [1]
0-255
White (0-Black - 255-100%)
7 5 5 5 5 RED LED - LED [2]
0-255 Red (0-Black - 255-100%)
8 6 6 6 6 GREEN LED - LED [2]
0-255
Green (0-Black - 255-100%)
9 7 7 7 7
BLUE LED - LED [2]
0-255 Blue (0-Black - 255-100%)
8 8 8 8
WHITE LED - LED [2]
0-255
White (0-Black - 255-100%)
10 9 9 9 9 RED LED - LED [3]
0-255 Red (0-Black - 255-100%)
11 10 10 10 10 GREEN LED - LED [3]
0-255
Green (0-Black - 255-100%)
12 11 11 11 11
BLUE LED - LED [3]
0-255 Blue (0-Black - 255-100%)
12 12 12 12
WHITE LED - LED [3]
0-255
White (0-Black - 255-100%)

www.elationlighting.com
17 ACL PAR 200IP™ User Manual
ELATION© ACL PAR 200IP™
DMX Channel Values / Functions Version 1 (35 DMX Channels)
Specifications are subject to change without any prior written notice.
*Control of LEDs depends on the Pixel Flip setting. | **CH27 Mode does not include channels 4, 5, 6, 22, 23, 24.
DMX CHANNEL MODE VALUE FUNCTION
4CH1:04 4CH2:04 6CH 8CH 10CH 12CH 27CH 28CH 30CH 32CH 35CH 16 BIT CHANNELS
13 13 13 13 13 RED LED - LED [4]
0-255
Red (0-Black - 255-100%)
14 14 14 14 14 GREEN LED - LED [4]
0-255
Green (0-Black - 255-100%)
15 15 15 15 15
BLUE LED - LED [4]
0-255
Blue (0-Black - 255-100%)
16 16 16 16
WHITE LED - LED [4]
0-255
White (0-Black - 255-100%)
16 17 17 17 17 RED LED - LED [5]
0-255
Red (0-Black - 255-100%)
17 18 18 18 18 GREEN LED - LED [5]
0-255
Green (0-Black - 255-100%)
18 19 19 19 19
BLUE LED - LED [5]
0-255
Blue (0-Black - 255-100%)
20 20 20 20
WHITE LED - LED [5]
0-255
White (0-Black - 255-100%)
19 21 21 21 21 RED LED - LED [6]
0-255
Red (0-Black - 255-100%)
20 22 22 22 22 GREEN LED - LED [6]
0-255
Green (0-Black - 255-100%)
21 23 23 23 23
BLUE LED - LED [6]
0-255
Blue (0-Black - 255-100%)
24 24 24 24 WHITE LED - LED [6]
0-255
White (0-Black - 255-100%)
25 25 25 25 25 RED LED - LED [7]
0-255
Red (0-Black - 255-100%)
26 26 26 26 26 GREEN LED - LED [7]
0-255
Green (0-Black - 255-100%)
27 27 27 27 27
BLUE LED - LED [7]
0-255
Blue (0-Black - 255-100%)
28 28 28 28 WHITE LED - LED [7]
0-255
White (0-Black - 255-100%)

www.elationlighting.com
18 ACL PAR 200IP™ User Manual
ELATION© ACL PAR 200IP™
DMX Channel Values / Functions Version 1 (35 DMX Channels)
Specifications are subject to change without any prior written notice.
*Control of LEDs depends on the Pixel Flip setting. | **CH27 Mode does not include channels 4, 5, 6, 22, 23, 24.
DMX CHANNEL MODE VALUE FUNCTION
4CH1:04 4CH2:04 6CH 8CH 10CH 12CH 27CH 28CH 30CH 32CH 35CH 16 BIT CHANNELS
1 5 5
COLOR MACROS
0 NO Function
1-4 Color Macro 01
5-8 Color Macro 02
9-12 Color Macro 03
13-16 Color Macro 04
17-20 Color Macro 05
21-24 Color Macro 06
25-28 Color Macro 07
29-32 Color Macro 08
33-36 Color Macro 09
37-40 Color Macro 10
41-44 Color Macro 11
45-48 Color Macro 12
49-52 Color Macro 13
53-56 Color Macro 14
57-60 Color Macro 15
61-64 Color Macro 16
65-68 Color Macro 17
69-72 Color Macro 18
73-76 Color Macro 19
77-80 Color Macro 20
81-84 Color Macro 21
85-88 Color Macro 22
89-92 Color Macro 23
93-96 Color Macro 24
97-100 Color Macro 25
101-104 Color Macro 26
105-108 Color Macro 27
109-112 Color Macro 28
113-116 Color Macro 29
117-120 Color Macro 30
121-124 Color Macro 31
125-128 Color Macro 32

www.elationlighting.com
19 ACL PAR 200IP™ User Manual
ELATION© ACL PAR 200IP™
DMX Channel Values / Functions Version 1 (35 DMX Channels)
Specifications are subject to change without any prior written notice.
*Control of LEDs depends on the Pixel Flip setting. | **CH27 Mode does not include channels 4, 5, 6, 22, 23, 24.
DMX CHANNEL MODE VALUE FUNCTION
4CH1:04 4CH2:04 6CH 8CH 10CH 12CH 27CH 28CH 30CH 32CH 35CH 16 BIT CHANNELS
1 5 5
COLOR MACROS [continued]
129-132 Color Macro 33
133-136 Color Macro 34
137-140 Color Macro 35
141-144 Color Macro 36
145-148 Color Macro 37
149-152 Color Macro 38
153-156 Color Macro 39
157-160 Color Macro 40
161-164 Color Macro 41
165-168 Color Macro 42
169-172 Color Macro 43
173-176 Color Macro 44
177-180 Color Macro 45
181-184 Color Macro 46
185-188 Color Macro 47
189-192 Color Macro 48
193-196 Color Macro 49
197-200 Color Macro 50
201-204 Color Macro 51
205-208 Color Macro 52
209-212 Color Macro 53
213-216 Color Macro 54
217-220 Color Macro 55
221-224 Color Macro 56
225-228 Color Macro 57
229-232 Color Macro 58
233-236 Color Macro 59
237-240 Color Macro 60
241-244 Color Macro 61
245-248 Color Macro 62
249-252 Color Macro 63
253-255 Color Macro 64
2 6 5 6 29 29
STROBE
0-31 NO Function
32-63 LEDs ON
64-95 Strobe Effect SLOW to FAST
96-127 LEDs ON
128-159 Pulse Effect Sequence SLOW to FAST
160-191 LEDs ON
192-223 Random Strobe Effect SLOW to FAST
224-255 LEDs ON

www.elationlighting.com
20 ACL PAR 200IP™ User Manual
ELATION© ACL PAR 200IP™
DMX Channel Values / Functions Version 1 (35 DMX Channels)
Specifications are subject to change without any prior written notice.
*Control of LEDs depends on the Pixel Flip setting. | **CH27 Mode does not include channels 4, 5, 6, 22, 23, 24.
DMX CHANNEL MODE VALUE FUNCTION
4CH1:04 4CH2:04 6CH 8CH 10CH 12CH 27CH 28CH 30CH 32CH 35CH 16 BIT CHANNELS
3 5 7 6 7 29 30 30 MASTER DIMMER
0-255 0 to 100%
4 6 8 7 8 30 31 31 FINE DIMMER [16BIT]
0-256 1 to 100%
8 9 32
AUTO PROGRAMS
0 NO FUNCTION
1-20 PROGRAM MACRO 01
21-40 PROGRAM MACRO 02
41-60 PROGRAM MACRO 03
61-80 PROGRAM MACRO 04
81-100 PROGRAM MACRO 05
101-120 PROGRAM MACRO 06
121-140 PROGRAM MACRO 07
141-160 PROGRAM MACRO 08
161-180 PROGRAM MACRO 09
181-200 PROGRAM MACRO 10
201-220 PROGRAM MACRO 11
221-240 PROGRAM MACRO 12
241-250 PROGRAM MACRO 13
251-255 PROGRAM MACRO 14
9 10 33 AUTO PROGRAM SPEED
0-255 Program Speed SLOW to FAST
10 11 34 AUTIO PROGRAM FADE
0-255 Program Fade SLOW to FAST
12 32 35
DIMMING CURVE MODES
0-20 STANDARD
21-40 STAGE
41-60 TV
61-80 ARCHITECTURAL
81-100 THEATRE
101-255 Default to Unit Setting