Elation Power Wash 250B User manual

User Manual
Software Version 1.19 Revised 6/2003

Power Wash 250™
©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 2

Power Wash 250™
©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 3
Table of contents
i Introduction............................................................................................................. 5
ii Unpacking ............................................................................................................... 5
iii Customer Support .................................................................................................. 5
iv Discharge Lamp Warning ..................................................................................... 5
v. Safety instructions ................................................................................................. 7
1. Features and Functions ......................................................................................... 8
2Installation............................................................................................................. 10
2.1 Mounting ........................................................................................................ 11
2.1.1 Clamps ................................................................................................ 11
2.1.2 Mounting plate ..................................................................................... 11
2.2 Secure the POWER WASH 250™ ................................................................. 12
2.3 Connections ................................................................................................... 13
2.3.1 Power Supply....................................................................................... 13
2.3.2 DMX..................................................................................................... 13
2.4 Fuse ............................................................................................................... 15
3The Menu Field...................................................................................................... 16
3.1 DMX- Addressing (D001)................................................................................ 18
3.2 Test Mode (TEST)............................................................................................ 18
3.3 Audio Mode (AUDI)......................................................................................... 18
3.4 Lamp On/Off (LAMP)....................................................................................... 19
3.5 Fixture Reset (RESE)...................................................................................... 19
3.6 Running Time - Lamp and Fixture (TIME)........................................................ 19
3.7 Continuous Color Wheel (FCOL)..................................................................... 19
3.8 Inverting Pan Movements (RPAN).................................................................. 19
3.9 Inverting Tilt Movements (RTLT)...................................................................... 20
3.10 Special Functions (SPEC)............................................................................... 20
3.10.1 Manual Drive (MANU).......................................................................... 20
3.10.2 Automatic Lamp On (LAAU)................................................................ 21
3.10.3 Lamp Off via DMX (DLOF)................................................................... 21
3.10.4 DMX Input (DMXI)................................................................................ 21

Power Wash 250™
©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 4
3.10.5 Display (DISP)..................................................................................... 22
3.10.6 Fixture Temperature (TEMP)................................................................ 22
3.10.7 Fan Control (FANS)............................................................................. 22
3.10.8 Adjustments and Calibrations (ADJU)................................................. 23
3.10.9 Default Settings (DFSE)....................................................................... 23
3.10.10 Feedback (FEED)............................................................................ 24
3.10.11 Correction of faults (EFLD).............................................................. 24
3.11 Error and Information Messages .................................................................... 24
4Operation............................................................................................................... 25
DMX Operation....................................................................................................... 25
Stand-Alone Operation ........................................................................................... 25
Master/Slave Operation .......................................................................................... 26
5DMX Channel Selection (DMX Protocol)............................................................. 27
6Service and Maintenance..................................................................................... 29
6.1 Lamp Change ................................................................................................... 29
6.2 Removing the Lamp.......................................................................................... 29
6.3 Optimizing the Lamp......................................................................................... 30
7 Fuse Replacement ................................................................................................ 32
8 Maintenance and Cleaning................................................................................... 33
Cleaning Frequency (rule-of-thumb) ....................................................................... 33
Cleaning the Optical System................................................................................... 34
9Color Wheel Oreintation....................................................................................... 35
10 Technical Specification........................................................................................ 36
11 Warranty................................................................................................................. 37

Power Wash 250™
©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 5
INTRODUCTION: Congratulations, you have just purchased one of the most
innovative and reliable lighting fixtures on the market today! The Power Wash 250B™
has been designed to perform reliably for years when the guidelines in this booklet are
followed. Please read and understand the instructions in this manual carefully and
thoroughly before attempting to operate this fixture. These instructions contain important
information regarding safety during use and maintenance.
UNPACKING: Thank you for purchasing the Elation Professional® Power Wash
250B.™ Every Power Wash 250B™ has been thoroughly bench tested and has been
shipped in perfect operating condition with the lamp installed and optimized. Carefully
check the shipping carton for damage that may have occurred during shipping. If the
carton appears to be damaged, carefully inspect your fixture for damage and be sure all
accessories necessary to operate the fixture have arrived intact. In the event damage
has been found or parts are missing, please contact our customer support team for
further instructions. Please do not return this fixture to your dealer without first
contacting customer support at the number listed below.
CUSTOMER SUPPORT: Elation Professional®provides a customer support line to
provide set up help and to answer any questions should you encounter problems during
your set up or initial operation. You may also visit our forum on the web at
www.elationlighting.com for any comments or suggestions. For service related issue
please contact Elation Professional®. Service Hours are Monday through Friday 9:00
a.m. to 5:00 p.m. Pacific Standard Time.
Voice: [phone]
Fax: [phone]
E-mail: [e-mail]
Warning! To prevent or reduce the risk of electrical shock or fire, do not expose this
fixture to rain or moisture.
Caution! There are no user serviceable parts inside this fixture. Do not attempt any
repairs yourself; doing so will void your manufactures warranty.
Please do not discard the shipping carton in the trash. Please recycle when ever
possible.

Power Wash 250™
©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 6
WARRANTY REGISTRATION: The Power Wash 250B™carries a two year (730
days) limited warranty. Please fill out the enclosed warranty card to validate your
purchase. All returned service items whether under warranty or not, must be freight pre-
paid and accompany a return authorization (R.A.) number. The R.A. number must be
clearly written on the outside of the return package. A brief description of the problem as
well as the R.A. number should also be included in the shipping container. If the fixture
is under warranty, you must provide a copy of your proof of purchase invoice. You may
obtain a R.A. number by contacting customer support at [phone].
DISCHARGE LAMP WARNING: This fixture is fitted with a
discharge lamp, which is highly susceptible to damage if improperly
handled. Never touch the lamp with your bare hands, as the oil from
your hands will shorten lamp life. Also, never move the fixture until
the lamps have had ample time to cool. Remember, lamps are not
covered under warranty conditions.
This fixture emits intense UV radiation, which is harmful to the eyes and skin. The
intense luminance of the lamp can cause severe damage to the retina. Never operate
this fixture with the protective covers removed, these covers have been specially
designed to shield against UV radiation.
Avoid switching the fixture on and off repeatedly in short intervals, as this will reduce
lamp life and intensity.
To achieve the intensity associated with discharge lamps, these lamps use gas sealed
in a high-pressure environment to emit a brilliant output. Due to the high pressure
involved with the construction of the lamp, the lamp may explode during prolonged
extensive use. This risk is increased with age; added care is encouraged when dealing
with older lamps. Extreme caution should be used when operated this or any fixture
fitted with a gas discharge lamp.
Epileptic Warning: Those suffering from epilepsy should avoid looking directly into
the lamp at all times.
Never open this fixture while in use!
During the initial operation of this fixture, a light smoke or smell may emit from
the interior of the fixture. This is a normal process and is caused by excess paint
in the interior of the casing burning off from the heat associated with the lamp.

Power Wash 250™
©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 7
V. Safety Instructions
The Power Wash 250B™ is an extremely sophisticated piece of
electronic equipment. To guarantee a smooth operation, it is
important to follow the guidelines in this manual. The
manufacturer of this device will not accept responsibility for
damages resulting from the misuse of this fixture due to the
disregard of the information printed in this manual.
1. Always be sure that the fan and the air inlets remain clean and are never
blocked. Allow about 6” (15cm) between this fixture and other devices or a wall
to allow for proper cooling.
2. Never touch the fixture during normal operation. This can cause severe
personal injuries and/or damage to the fixture.
3. Be sure to unplug the POWER WASH 250B™ from the power outlet
before performing any service related issues.
4. Allow at least 30 minutes after disconnecting the AC before you open the
POWER WASH 250™. To prevent personal injury, never touch the lamp if you
are not absolutely sure it has cooled.
5. Never look directly into the lamp beam. You risk injury to your retina, which
may induce blindness.
6. Be sure to track and record the lamp running time. The lamp should be
changed at the end of the specified lamp life, regardless of lamp output. You
may also have to change the lamp if it shows any deformations or damage.
The same is with all glass components, color filters, lenses and mirrors.
7. For safe operation, follow the installation guide described in chapter two of this
manual. Operating the POWER WASH 250B™ without suited safety aids such
as safety cables or clamps can increase the risk of damage and/or personal
injury.
8. Qualified personnel should only perform installation.
9. When mounting this fixture, use only the original rigging parts included with
this fixture. Any structural modification will void the original manufactures
warranty and may increase the risk of damage and/or personal injury.
10. To reduce the risk of fire or shock, do not expose this unit to rain or moisture.
11. Do not attempt to operate this fixture if the power cord is frayed or damaged.

Power Wash 250™
©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 8
1. Features and Functions
1
2
3
4
1. Lens Assembly
2. Arm
3. Base
4. Carrying
handles
5. Up button
6. Down button
7. Enter button
8. Mode button
9. LED Display
10.Firmware Connection
11.Microphone Sensitivity
12.DMX Input Jack
13.DMX Output Jack
14.Power On/Off Switch
15.Fuse Holder
16.Fan (air inlet)
Max
Min
DMX IN
DMX OUT
Software
Update
1
.
G
r
o
u
n
d
2
.
D
a
t
a
-
3
.
D
a
t
a
+
POWER
210V~
230V~
250V~
50Hz
60Hz
Power
input
FUSE:
T3.15A
@250V
LAMP:
MSD 250W
Seria
l
n
u
m
b
e
r
:
Fuse
Mic
Sensitive
1
2
3
P
U
S
H
FUS
E
MODE
ENTER
UP
DOWN
M
O
D
E
E
N
T
E
R
U
P
D
O
W
N
8
7
6
5
9
10
11
12
13
14
15
16
COLO
R
COLO
R

Power Wash 250™
©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 9
1. Lens Assembly - This high quality lens assembly is fully focusing. Focus the
lens by loosening the locking screws mounted on the top and bottom of the
head assembly. Then using the screws to grasp the lens assembly, slide the
lens back and forth until the desired focus is achieved. Then tighten down on
the locking screws to retaining your focus.
2. Retaining Arm – This Arm serves as a conduit for all electronic from the base
to the head assembly.
3. Base – The fixture base holds all the main electronics for the fixture and
provides a means to secure the fixture to a wall or ceiling.
4. Carrying Handles - Be sure to always carry the fixture by the built-in handles.
Never lift or carrying the fixture by the head or yoke. Pulling on or transporting
the fixture by the head assembly may severely damage the fixture and will void
the fixture warranty.
5. Up Button - This button is used to scroll forward when navigating through the
system menu.
6. Down Button - This button is used to scroll backwards when navigating
through the system menu.
7. Enter Button - This button is used to select and confirm a function when
working in the system menu.
8. Mode Button – This button is used to access the fixture’s main system menu
and programming functions.
9. LED Display – This display is used to detail the menu and operating functions.
10.Firmware Connection – This connection is to be used solely by a qualified
technician to upgrade and test the fixture.
11.Microphone - This microphone receives external low frequencies to trigger the
fixture in Sound-Active and Master/Slave modes.

Power Wash 250™
©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 10
12.DMX Input Jack – This jack is used to receive an incoming DMX signal or
Master/Slave signal.
13.DMX Output Jack – This jack is used to transmit the incoming DMX signal to
another DMX fixture, or transmit a Master/Slave signal to the next Power Wash
250B™ in the chain. For best results in DMX or Master/Slave mode terminate
this jack if it is the last fixture in the chain. See “Terminator” on page 14.
14.Power Switch – This switch is used to control main power to the fixture.
15.Fuse Holder – This housing stores a 7 amp (3.15 amp 220v) GMA protective
fuse. Never defeat the fuse, the fuse is designed to protect the electronics in
the event of sever power fluctuations. Always be sure to replace the fuse with
an exact match as to the one being replaced, unless otherwise told to do so by
an authorized Elation®service technician. Please note; when the fixture
orginally ships from the factory we included a 6.3 amp fuse. This fuse may
safely be replaced with a 7 amp fuse.
16.Cooling Fan - This fixture is equipped with a high velocity variable fan to aid in
the cooling process. This fan is designed to vary its’ velocity at different
operating temperatures, to provide better cooling when the fixture reached
higher operating temperatures associated with long usage. Be sure to never
obstruct the cooling fan during normal usage. Also, be sure to keep this vent
clean at all times. A blocked or malfunctioning cooling system may shorten
lamp life and fixture reliability.
2. Installation

Power Wash 250™
©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 11
2.1 Mounting
The POWER WASH 250B™ is fully operational in two different mounting
positions, hanging upside from a ceiling or set on a flat level surface. To avoid
internal damage to the unit, never mount the unit on its side as illustrated below.
Be sure this fixture is kept at least 0.5m away from any flammable materials
(decoration etc.). Install a safety cable that can hold at least 10 times the weight of
the fixture. Never use the carrying handles for secondary attachment.
Refer to regulations BGV C1 (former VBG 70) and DIN VDE
0711-217 for proper installation in Europe
To ensure proper installation, only qualified staff should
attempt installation.
2.1.1 Clamps
Secure two clamps to the bottom of the POWER WASH 250B™ to mount
the fixture to truss. Refer to the printed instructions on the bottom of the
fixture for proper clamp installation.
2.1.2 Mounting plate
For a permanent installation of the POWER WASH 250B™ in a non-truss

Power Wash 250™
©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 12
installation you can use the optional mounting plate (secured to the bottom
of the fixture) to secure the fixture to a ceiling or a wall. The plate uses four
M6x20 screws.
3.2 Securing the POWER WASH 250™
Regardless of the rigging option you choose for your POWER WASH 250B™
always be sure to secure your fixture with a safety cable. The fixture provides a
built-in rigging point for a safety cable on the underside of the fixture, be sure to
use this point and never secure a safety cable to a carrying handle.
Safety Cable Rigging Point

Power Wash 250™
©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 13
3.3 Connections
3.3.1 Power supply
115v ~ 60Hz AC (America’s),
Connected load 500W <=> 4.4 A (blind current compensation)
or 230V ~ 50Hz AC (EU),
Connected load 500W <=> 2.2 A (blind current compensation)
Operating voltage is pre-selected at the factory and is not user selectable.
Because line voltage may vary from venue to venue, you should be sure
your fixture voltage matches that of the outlet. The voltage requirements for
the fixture are clearly printed on the side panel near the power cord.
3.3.2 DMX-512
3-Pin XLR Input/Output. [+] = Pin 3 / [-] = Pin 2 / [Ground] = Pin 1
3.4 DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used by
most lighting and controller manufactures as a form of communication between
intelligent fixtures and controllers. A DMX controller sends DMX data instructions
from the controller to the fixture. DMX data is sent as serial data that travels from
fixture to fixture via the DATA “IN” and DATA “OUT” XLR terminals located on all
DMX fixtures (most controllers only have a DATA “OUT” terminal). DMX Linking:
DMX is a language allowing all makes and models of different manufactures to be
linked together and operate from a single controller, as long as all fixtures and the
controller are DMX compliant. To ensure proper DMX data transmission, when
using several DMX fixtures try to use the shortest cable path possible. The order in
which fixtures are connected in a DMX line does not influence the DMX
addressing. For example; a fixture assigned a DMX address of 1 may be placed
anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle.
Therefore, the first fixture controlled by the controller could be the last fixture in the
chain. When a fixture is assigned a DMX address of 1, the DMX controller knows
to send DATA assigned to address 1 to that fixture, no matter where it is located in
the DMX chain.
3.5 Data Cable (DMX Cable) Requirements (For DMX and Master/Slave Operation):
The Power Wash 250B™ can be controlled via DMX-512 protocol. The Power
Wash 250B™ is a 14 channel DMX fixture. The DMX address is set electronically
using the controls on the side panel of the fixture. Your fixture and your DMX

Power Wash 250™
©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 14
controller require a standard 3-pin XLR connector for data input and data output
(Figure Below). If you are making your own cables, be sure to use standard two
conductor shielded cable (This cable may be purchased at almost all professional
sound and lighting stores). Your cables should be made with a male and female
XLR connector on either end of the cable. Also remember that DMX cable must be
daisy chained and can not be split.
2.6 Notice: Be sure to follow the above figure when making your own cables. Do not
use the ground lug on the XLR connector. Do not connect the cable’s shield
conductor to the ground lug or allow the shield conductor to come in contact with
the XLR’s outer casing. Grounding the shield could cause a short circuit and
erratic behavior.
2.7 Special Note: Line Termination. When longer runs of cable are used, you may
need to use a terminator on the last fixture to avoid erratic behavior. A terminator
is a 90-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a
male XLR connector (DATA + and DATA -). This fixture is inserted in the female
XLR connector of the last fixture in your daisy chain to terminate the line. Using a
cable terminator (ADJ part number Z-DMX/T) will decrease the possibilities of
erratic behavior.
2.8 5-Pin XLR DMX Connectors. Some manufactures use 5-pin XLR connectors for
DATA transmission in place of 3-pin. 5-pin XLR fixtures may be implemented in a
3-pin XLR DMX line. When inserting standard 5-pin XLR connectors in to a 3-pin
line a cable adaptor must be used, these adaptors are readily available at most
electric stores. The chart below details a proper cable conversion.

Power Wash 250™
©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 15
3.9 Fuse Requirements
The POWER WASH 250B™ electronic system is protected by a 5x20 mm external
fuse. 115V / T 6.3A (US model) or 230V / T 3.15A (EU model).
The fuse requirements are clearly printed on the side of the fixture.
WARNING:
•Always disconnect main power before changing a fuse!
•Always replace with the exact same type fuse unless otherwise
specified by an authorized Elation®service technician. Replacing with
anything other than the specified part can severely damage your
fixture and will void your manufactures warranty.

Power Wash 250™
©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 16
3 The Menu Field -
The control panel located on the side of the fixture allows you to
access the main menu and make all necessary adjustments to the
POWER WASH 250™. During normal operation, tapping the
“MODE” key once will access the fixture’s main menu. Once in the
main menu you can navigate through the different functions and
access the sub-menus with the Up and Down buttons. Once you
reach a field that requires adjusting, tap the ENTER button to
activate that field and use the UP and Down button to adjust the
field. Tapping the Enter button once more will confirm your setting.
Once a setting is saved the LED will briefly readout OK to confirm a
new setting has been made and locked into memory. You may exit
the main menu at any time without making any adjustments by
tapping the MODE button.
Level
1
Level
2
Level
3
DISCRIPTION
D0 01
Indicate the Staring DMX address
TE ST
Activates the fixtures self test mode
AU DI
AS LW
Activates Sound-Active mode (slow)
AF ST
Activates Sound-Active mode (fast)
MS TR
Runs fixture as “MASTER” for Audio, Master-Slave mode
SV PT
Runs fixture as “SLAVE” for Audio, Master-Slave mode
SI ZE
Room size adjustment (NORM-BIG-MIDL-SMAL) – This
adjustment is only functional when operating the fixture in
Sound-Active mode and makes adjustments to the pan and
tilt to coincide with a rooms dimensions
LA MP
Manually switches lamp “on” and “off”
RE SE
Resets the fixture’s pan, tilt, and internal wheels
TI ME
PO WR
Displays the total fixture running time (non destructible)
LA 1
Displays a lamps running time (erasable) – Reset this
reading after every lamp change to keep an accurate
account of a lamps running time
LA 2
Displays the total lamp running time (non destructible)
FC OL
Manually activates a continuous color wheel scroll
RP AN
Reverses the Pan movements
RT LT
Reverses the Tilts movements
SP EC
MA NU
Manual drive of all device functions
PA N
Pan Position, Channel 1
Ti lt
Tilt Position, Channel 3
CO LO
Color Wheel, Channel 5
SH UT
Shutter, Channel 9
DI MR
Dimmer, Channel 10
SP EC
Special Functions, Channel 12
LA AU
Automatic lamp start
DL OF
Switch off lamp via DMX
DM XI
Reed out actual DMX-values
DOWN - UP
DI SP
D ON
Display On/Off
MODE ENTER UPDOWN
MODEEN TERUP DOW N
LED-Display
Mode-key Enter-key Down-key Up-key

Power Wash 250™
©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 17
RE V
This function will flip the display read out 180˚
TE MP
Display the fixture’s internal temperature
FA NS
HI GH
Maximum cooling fan velocity
RE G
Automatic cooling fan control
LO OF
Low cooling fan speed lamp off
LO HI
Low cooling fan speed automatic
AD JU
CO DE
xx xx
Access the calibration menu with technician code (for
authorized person only)
CO LO
Calibration of the color wheel
cl re
Settings in the internal memory (technician only)
fa cc
Must read on. Protected by a code
AR ES
Adjust- Reset
DF SE
Resets all the fixture functions to the factory default values
FE ED
Pan/Tilt feedback (error correction) On/Off
EF LG
Fault corrections

Power Wash 250™
©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 18
3.1 Adjust the DMX- Address (D001)
After applying power to the POWER WASH 250B™ the LED will display the
fixture’s current DMX address. If the fixture is not receiving a DMX signal the
display will flash continuously.
D001
To set or adjust a DMX address, please follow the procedure below:
1. Switch on the POWER WASH 250B™ and wait for the fixture reset process to
finished ('RESE'will flash in the LED while fixture is in reset mode).
2. Press the Mode button to access the main menu. Toggle through the menu by
pressing the Up and Down buttons until the display shows D001. Tap the enter
button to make changes to the address, the current three digit address will
immediately begin to flash.
3. While the current three-digit address is flashing, use the Up and Down buttons
to select adjust the address. Lock your new address into by pressing the Enter
button. After the new address has been successfully stored into the fixture’s
memory the LED will briefly readout OK.
The DMX address is non-destructible and will remain in the fixture’s memory even
when the power has been switched off. Memory is backed-up and retained by an
internal power source with a five year shelf life.
3.2 The Test Program (TE ST)
Test
The Test Program launched the fixture’s internal test mode. This function runs a
complete test procedure of all functions. Press Enter to launch the self-test or the
Mode button to cancel.
3.3 The Audio Program (AUD I
The Audio menu allows you to run a stand-alone audio program. This program
can run either fast (AFST) or slow (Aslw); Fast (AFST): When running in “fast”
mode every sound impulse will trigger a new step. (Aslw): When running in You
may run several fixtures together at once to achieve a synchronized light show
running to sound in a Master/Slave configuration. To run in a Master/Slave.

Power Wash 250™
©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 19
3.4 Lamp On/Off (LAMP)
LAMP
This function allows you to manually control the lamp operation. Access the lamp
function in the main menu and use the use the Up and Down buttons to toggle
between lamp On and lamp Off. Press the Enter button to confirm the operation
or the Mode button to cancel and return to the main menu. (The lamp OF F
command will only functions if and when the shutter is closed at the same time).
3.5 Reset (RESE)
RESE
This function will rest and return all motors to the home position. Access the reset
function in the main menu and press the Enter button to engage the reset function
(RST will readout in the display).
3.6 Running time (TIME)
TIME
This menu function can read out three different fixture running times.
PO WR
Total fixture running time (non destructible).
LA 1
Lamp running time (erasable). Press and hold down the Up and Down
buttons together for three seconds to reset this function.
LA 2
Total lamp running time (non destructible).
3.7 Continuous Color Wheel (FCOL)
FCOL
This function changes the color wheel operation from continuous to step.
Continuous allows you to micro step the color wheel, which allows for split colors.
The step function will only the color wheel to step directly from one color to
another color, this function will not allow split coloring.
3.8 Invert Pan Movement (RPAN)
RPAN

Power Wash 250™
©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 20
This function allows you to invert all pan movements. Use the Up and Down
buttons to turn this function On and Off. Press the Enter button to accept the
change or the Mode button to cancel and return to the main menu.
3.9 Invert Tilt Movement (RTLT)
RTLT
This function allows you to invert all tilt movements. Use the Up and Down buttons
to turn this function On and Off. Press the Enter button to accept the change or
the Mode button to cancel and return to the main menu.
3.10 Special Functions (SPEC)
SPEC
This menu option accesses several special features and function of the POWER
WASH 250™. The SPEC sub-menu consists of several sub-menus. Navigation
details of the special functions and their sub-menus are as followed:
3.10.1 Manual Drive (MANU)
MANU
This feature allows you to drive all the unit’s functions manually for use in
an environment that requires a static position (no movements), determining
focus points, or testing. Use the Up and Down buttons to select the
function you wish to adjust, then use the Enter button to accept your
selection. Now adjust the values with the Up and Down buttons and use
the Enter button to lock in your value. Use the Mode button to cancel at
any time.
Function
Value
Remark
PA N
00 0 - 255
Pan Position
TI LT
00 0 - 255
Tilt Position
CO LO
00 0 - 255
Color wheel (fixed colors)
SH UT
00 0 - 255
Shutter / Strobe function (the lamp strikes at
DMX 255 if dimmer is "open" = DMX 255)
DI MR
00 0 - 255
Dimmer
BS PR
00 0 - 255
Beam shape + Frost
SP EC
00 0 - 255
Lamp Off, Reset, ...