Elation EPAR TRI User manual

User Instructions
EPAR TRI Introduction
Elation Professional - www.elationlighting.com - EPAR TRI Instruction Manual Page 2
2/12
Unpacking: Thank you for purchasing the EPAR TRI by Elation Pro-
fessional®. Every EPAR TRI has been thoroughly tested and has been
shipped in perfect operating condition. Carefully check the shipping
carton for damage that may have occurred during shipping. If the
carton appears to be damaged, carefully inspect your xture for any
damage and be sure all accessories necessary to operate the unit has
arrived intact. In the case damage has been found or parts are missing,
please contact our customer support number for further instructions.
Do not return this unit to your dealer without rst contacting customer
support.
Introduction: The EPAR TRI is part of Elation Professionals®con-
tinuing pursuit for creating high quality affordable intelligent fixtures.
The EPAR TRI is a powerful DMX intelligent 3-in-1 RGB (Red, Green, &
Blue) LED wash. This wash is light weight and compact which makes
it a great piece for mobile DJ’s and clubs. This unit can be used as a
stand alone, or a sound-active mode. The unit can also be controlled
via DMX controller.
Customer Support: ©Elation®provides a customer support line, to
provide set up help and to answer any question should you encounter
problems during your set up or initial operation. You may also visit us
on the web at www.elationlighting.com for any comments or sugges-
tions. Service Hours are Monday through Friday 8:00 a.m. to 4:30 p.m.
Pacic Standard Time.
Voice: [phone]
Fax: [phone]
E-mail: [email protected]
Warning! To prevent or reduce the risk of electrical shock or re, do
not expose this unit to rain or moisture.
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures war-
ranty. In the unlikely event your unit may require service please contact
©Elation customer support.
PLEASE recycle the shipping carton when ever possible.
EPAR TRI

EPAR TRI Safety Precautions
Elation Professional - www.elationlighting.com - EPAR TRI Instruction Manual Page 4Elation Professional - www.elationlighting.com - EPAR TRI Instruction Manual Page 3
• To reduce the risk of electrical shock or re, do not expose this unit
rain or moisture
• Do not spill water or other liquids into or on to your unit.
• Do not attempt to operate this unit if the power cord has been
frayed or broken. Do not attempt to remove or break o the ground
prong from the electrical cord. This prong is used to reduce the risk
of electrical shock and re in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user
serviceable parts inside.
• Never operate this unit when it’s cover is removed.
• Never plug this unit in to a dimmer pack
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• This unit is intended for indoor use only, use of this product out`
doors voids all warranties.
• During long periods of non-use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power-supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them,
paying particular attention to the point they exit from the unit.
• Cleaning -The fixture should be cleaned only as recommended by
the manufacturer. See page 16 for cleaning details.
• Heat -The appliance should be situated away from heat sources
such as radiators, heat registers, stoves, or other appliances (inclu-
ding amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a
marked change in performance.
EPAR TRI Warranty Registration
EPAR TRI Features
To optimize the performance of this product, please read these
operating instructions carefully to familiarize yourself with the basic
operations of this unit. These instructions contain important safety
information regarding the use and maintenance of this unit. Please
keep this manual with the unit, for future reference.
EPAR TRI General Instructions
• Multi-Colors
• Built in Microphone
• Four Operating Modes
• DMX-512 protocol
• Six DMX Modes: 1 Channel Mode, 2 Channel Mode, 3 Channel
Mode, 4 Channel Mode, 6 Channel Mode, & 7 Channel Mode
• Dimming 0-100% in 2 Channel Mode, 4 Channel Mode, 5 Channel
Mode, 6 Channel Mode, & 7 Channel Mode.
• Daisy Chain Units Together in DMX Mode
The EPAR TRI carries a two year limited warranty. Please fill out the
enclosed warranty card to validate your purchase. All returned service
items whether under warranty or not, must be freight pre-paid and
accompany a return authorization (R.A.) number. The R.A. number
must be clearly written on the outside of the return package. A brief
description of the problem as well as the R.A. number must also be
written down on a piece of paper included in the shipping carton. If
the unit is under warranty, you must provide a copy of your proof of
purchase invoice. You may obtain a R.A. number by contacting our
customer support team on our customer support number. All pack-
ages returned to the service department not displaying a R.A. number
on the outside of the package will be returned to the shipper.

Power Supply: The Elation EPAR TRI contains a automatic voltage
switch, which will auto sense the voltage when it is plugged into the
power source. With this switch there is no need to worry about the cor-
rect power voltage, this unit can be plugged in anywhere.
DMX-512: DMX is short for Digital Multiplex. This is a universal pro-
tocol used by most lighting and controller manufactures as a form of
communication between intelligent fixtures and controllers. A DMX
controller sends DMX data instructions from the controller to the fix-
ture. DMX data is sent as serial data that travels from fixture to fixture
via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX
fixtures (most controllers only have a DATA “OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of
dierent manufactures to be linked together and operate from a single
controller, as long as all xtures and the controller are DMX compli-
ant. To ensure proper DMX data transmission, when using several
DMX fixtures try to use the shortest cable path possible. The order
in which fixtures are connected in a DMX line does not influence the
DMX addressing. For example; a fixture assigned a DMX address of 1
may be placed anywhere in a DMX line, at the beginning, at the end,
or anywhere in the middle. When a fixture is assigned a DMX address
of 1, the DMX controller knows to send DATA assigned to address 1
to that unit, no matter where it is located in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX Operation):
The EPAR TRI has 6 DMX Channel Modes. The DMX address is set
electronically using the controls on the rear panel of the unit. Your unit
and your DMX controller require a approved DMX-512 110 Ohm Data
cable for data input and data output. We recommend Accu-Cable DMX
cables. If you are making your own cables, be sure to use standard
110-120 Ohm shielded cable (This cable may be
purchased at almost all professional sound and
lighting stores). Your cables should be made with
a male and female XLR connector on either end of
the cable. Also remember that DMX cable must be
daisy chained and cannot be split.
Elation Professional - www.elationlighting.com - EPAR TRI Instruction Manual Page 5
EPAR TRI Set Up
Elation Professional - www.elationlighting.com - EPAR TRI Instruction Manual Page 6
EPAR TRI Set Up
Special Note: Line Termination. When longer runs of cable are
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con-
nected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
DMX512 IN
3-PIN XLR
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
1
2
3
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
1
2
3
1
2
3
DMX +
DMX -
COMMON
DMX512 OUT
3-PIN XLR
5-Pin XLR DMX Connectors. Some manufactures use 5-pin DMX-
512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
xtures may be implemented in a 3-pin DMX line. When inserting
standard 5-pin data cables in to a 3-pin line a cable adaptor must be
used, these adaptors are readily available at most electric stores. The
chart below details a proper cable conversion.
Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)
Pin 1
Do Not Use
Do Not Use
Pin 3
Pin 2
Pin 1
Pin 3
Pin 2
Not Used
Not Used
Data True (+ signal)
Data Compliment (- signal)
Ground/Shield
3-Pin XLR to 5-Pin XLR Conversion
Figure 1

LED Display On/Off:
To set the LED display to turn off after 10 seconds, press the MODE
button until ds-X is displayed, “X” representing either 1 or 2. Press
the UP or DOWN button so that ds-2 is displayed, now the display
will turn off after 10secs. Press any button for at least 5secs. to turn
the display on again. Be advised though that the display will turn off
automatically after 10 seconds of inactivity.
ds-1= LCD display on at all times.
ds-2= LCD display shuts off after 10 seconds.
Operating Modes:
You can use the EPAR TRI in four ways:
• Macro Mode - There are 32 color macros to choose from.
• Auto Mode - There are 6 built in programs to choose from.
• RGB mode - Control the intensity of all three colors adjusting the
intensity to your desire.
• DMX control mode - This function will allow you to control each
individual fixtures traits with a standard DMX 512 controller such as
as the Elation® Show Designer™.
Macro Mode:
1. Plug the fixture in and press the MODE button until “8-XX” is dis-
played. “XX” representing a number betweet 0-32.
2. There are 32 macros to choose from. Select your desired macro by
pressing the UP and DOWN buttons.
Program Mode:
1. Plug the fixture in and press the MODE button until “9-XX” is dis-
played. “XX” representing a number betweet 1-06 or AL.
2. There are 6 built-in programs to choose from. Select your desired
program by pressing the UP and DOWN buttons. You can set your
program speed by following the next set of instructions.
Program Mode Speed Adjustment:
1. To adjust the speed of your program press the MODE button until
“A-XX” is displayed.
2. Press the UP or DOWN buttons to make the adjustmetns. “A-01” is
the slowest speed, “A-16” the fastest speed. When the display
reads “A-So” the Auto mode is running by sound activity.
EPAR TRI Operating Instructions
Elation Professional - www.elationlighting.com - EPAR TRI Instruction Manual Page 8Elation Professional - www.elationlighting.com - EPAR TRI Instruction Manual Page 7
RGB Mode:
1. Plug the fixture in and press the MODE button until:
2. When rXXX is displayed you are in Red dimming mode. Press the
UP and DOWN buttons to adjust intensity.
3. When GXXX is displayed you are in Green dimming mode. Press the
UP and DOWN buttons to adjust intensity.
4. When bXXX is displayed you are in Blue dimming mode. Press the
UP and DOWN buttons to adjust intensity.
DMX Mode:
Operating through a DMX controller givesthe user the freedom to create
their own programs tailored to their own individual needs. The EPAR TRI
has 6 DMX modes: 1 Channel mode, 2 Channel mode, 3 Channel mode,
4 Channel mode, 6 Channel mode, and a 7 Channel mode. See pages
10-13 for each modes’ DMX traits.
1. This function will allow you to control each individual fixture’s traits
with a standard DMX 512 controller such as the Elation® Show
Designer™ or the Elation® DMX Operator™.
2. To run your fixture in DMX mode, plug in the fixture via the XLR con-
nections to any standard DMX controller. Select your desired DMX
mode, and then press the UP or DOWN buttons to adjust the DMX
address. XXX = DMX Address
3. To run the 1 Channel Mode, press the MODE button until “1XXX”
is displayed. This is the DMX addressing for the 1 Channel Mode.
4. To run the 2 Channel Mode, press the MODE button until “2XXX”
is displayed. This is the DMX addressing for the 2 Channel Mode.
5. To run the 3 Channel Mode, press the MODE button until “3XXX”
is displayed. This is the DMX addressing for the 3 Channel Mode.
6. To run the 4 Channel Mode, press the MODE button until “4XXX”
is displayed. This is the DMX addressing for the 4 Channel Mode.
7. To run the 6 Channel Mode, press the MODE button until “5XXX”
is displayed. This is the DMX addressing for the 6 Channel Mode.
8. To run the 7 Channel Mode, press the MODE button until “6XXX”
is displayed. This is the DMX addressing for the 7 Channel Mode.
9. Please see pages 10-13 for DMX values and traits
EPAR TRI Operating Instructions

Elation Professional - www.elationlighting.com - EPAR TRI Instruction Manual Page 10Elation Professional - www.elationlighting.com - EPAR TRI Instruction Manual Page 9
EPAR TRI 1 Channel Mode - DMX Values and Functions
Channel Value Function
1 COLOR MACROS
0 OFF
1 - 7 BASTARD AMBER
8 - 15 MEDIUM AMBER
16 - 23 PALE AMBER GOLD
24 - 31 GALLO GOLD
32 - 39 GOLDEN AMBER
40 - 47 LIGHT RED
48 - 55 MEDIUM RED
56 - 63 MEDIUM PINK
64 - 71 BROADWAY PINK
72 - 79 FOLLIES PINK
80 - 87 LIGHT LAVENDER
88 - 95 SPECIAL LAVENDER
96 - 103 LAVENDER
104 - 111 INDIGO
112 - 119 HEMSLEY BLUE
120 - 127 TIPTON BLUE
128 - 135 LIGHT STEEL BLUE
136 - 143 LIGHT SKY BLUE
144 - 151 SKY BLUE
152 - 159 BRILLIANT BLUE
160 - 167 LIGHT GREEN BLUE
168 - 175 BRIGHT BLUE
176 - 183 PRIMARY BLUE
184 - 191 CONGO BLUE
192 - 199 PALE YELLOW GREEN
200 - 207 MOSS GREEN
208 - 215 PRIMARY GREEN
216 - 223 DOUBLE CTB
224 - 231 FULL CTB
232 - 239 HALF CTB
240 - 247 DARK BLUE
248 - 255 WHITE
Master-Slave Operation:
This function will allows you to link units together to run in a Master-Slave
mode. In Master-Slave operation one unit will act as the controlling unit
and the others will react to the controlling units built-in programs. Any
unit can act as a Master or as a Slave however, only one unit can be pro-
grammed to act as the “Master.”
Master-Slave Connections and Settings:
1. Daisy chain your units via the XLR connector on the rear of the unit.
Use standard XLR data cables to link your units together. Remem-
ber that the Male XLR connector is the input and the Female XLR
connector is the ouput. The first unit in the chain (master) will use
the female XLR connector only. The last unit in the chain will use the
male XLR connector only.
2. Set the “Master” unit to your desired mode or operation.
3. For the “Slave” unit(s), set the display to any DMX channel mode.
Example: Set the unit to 4 channel mode, the display should read
“3000” or any variables, i.e “3001”, “3002 etc..
4. Connect the “Slave” unit or units and they will automatically start to
follow the “Master.”
EPAR TRI Master-Slave Configuration

EPAR TRI 6 Channel Mode - DMX Values and Functions
Channel Value Function
1 RED
0 - 255 0% - 100%
2 GREEN
0 - 255 0% - 100%
3 BLUE
0 - 255 0% - 100%
4 1 - 255 COLOR MACROS
PLEASE SEE 1 CHANNEL MODE
5 0 - 15 NOTHING
16 - 255 STROBING/SPEED CONTROL
6 MASTER DIMMER
0 - 255 0% - 100%
Channel 1, 2, & 3 will not work, when Channel 4 is being used.
Elation Professional - www.elationlighting.com - EPAR TRI Instruction Manual Page 12Elation Professional - www.elationlighting.com - EPAR TRI Instruction Manual Page 11
EPAR TRI 2 Channel Mode - DMX Values and Functions
Channel Value Function
1 1 - 255 COLOR MACROS
PLEASE SEE 1 CHANNEL MODE
2 0 - 255 MASTER DIMMER 0% - 100%
EPAR TRI 3 Channel Mode - DMX Values and Functions
Channel Value Function
1 RED
0 - 255 0% - 100%
2 GREEN
0 - 255 0% - 100%
3 BLUE
0 - 255 0% - 100%
EPAR TRI 4 Channel Mode - DMX Values and Functions
Channel Value Function
1 RED
0 - 255 0% - 100%
2 GREEN
0 - 255 0% - 100%
3 BLUE
0 - 255 0% - 100%
4 MASTER DIMMER
0 - 255 0% - 100%

Elation Professional - www.elationlighting.com - EPAR TRI Instruction Manual Page 13 Elation Professional - www.elationlighting.com - EPAR TRI Instruction Manual Page 14
Channel 1, 2, & 3 will not work, when Channel 4 is being used.
When using Channel 6, Channel 5 will control the speed of the
color changing.
EPAR TRI 8 Channel Mode - DMX Values and Functions
Channel Value Function
1 RED
0 - 255 0% - 100%
2 GREEN
0 - 255 0% - 100%
3 BLUE
0 - 255 0% - 100%
4 1 - 255 COLOR MACROS
PLEASE SEE 1 CHANNEL MODE
5 STROBING/PROGRAM SPEED
0 - 15 NOTHING
16 - 255 STROBING
SLOW - FAST
1 - 255 PROGRAM SPEED SLOW - FAST
6 MODE
0 - 127 OFF
128 - 159 AUTO MIX
160 - 191 3 COLOR JUMP
192 - 223 7 COLOR JUMP
224 - 255 SOUND ACTIVE
7 MASTER DIMMER
0 - 255 0% - 100%
EPAR TRI Color Macro Chart
BASTARD AMBER
MEDIUM AMBER
PALE AMBER GOLD
GALLO GOLD
GOLDEN AMBER
LIGHT RED
MEDIUM RED
MEDIUM PINK
BROADWAY PINK
FOLLIES PINK
LIGHT LAVENDER
SPECIAL LAVENDER
LAVENDER
INDIGO
HEMSLEY BLUE
TIPTON BLUE
LIGHT STEEL BLUE
LIGHT SKY BLUE
SKY BLUE
BRILLIANT BLUE
LIGHT GREEN BLUE
BRIGHT BLUE
PRIMARY BLUE
CONGO BLUE
PALE YELLOW GREEN
MOSS GREEN
PRIMARY GREEN
DOUBLE CTB
FULL CTB
HALF CTB
DARK BLUE
WHITE
COLOR RED BLUE
GREEN
255 206 143
255 255 255
1 134 201
52 148 209
0 142 208
0 38 86
88 2 163
147 164 212
119 130 199
175 77 173
224 5 97
234 139 171
96 0 11
176 17 0
254 121 0
254 165 98
254 192 138
254 177 153
107 156 231
8 107 222
0 46 35
42 165 85
209 219 182
0 40 86
1 100 167
0 97 166
0 83 115
0 129 184
0 121 192
0 145 212
165 198 247
0 0 189

Elation Professional - www.elationlighting.com - EPAR TRI Instruction Manual Page 15
EPAR TRI Cleaning
Due to fog residue, smoke, and dust cleaning the internal and exter-
nal optical lenses must be carried out periodically to optimize light
output.
1. Use normal glass cleaner and a soft cloth to wipe down the
outside casing.
2. Clean the external optics with glass cleaner and a soft cloth
every 20 days.
3. Always be sure to dry all parts completely before plugging
the unit back in.
Cleaning frequency depends on the environment in which the fixture
operates (i.e. smoke, fog residue, dust, dew).
EPAR TRI Trouble Shooting
Listed below are a few common problems the user may encounter,
with solutions.
Unit not responding to DMX:
1. Check that the DMX cables are connected properly and are
wired correctly (pin 3 is “hot”; on some other DMX devices
pin 2 may be ‘hot’). Also, check that all cables are connected
to the right connectors; it does matter which way the inputs
and outputs are connected.
Unit does not respond to sound:
1. Quiet or high pitched sounds will not activate the unit.
Elation Professional - www.elationlighting.com - EPAR TRI Instruction Manual Page 16
EPAR TRI Photometric Chart
EPAR TRI Photometric Beam Angle Data Standard 10° Beam Angle LUX x0.0929 = FC
R
G
B
ALL
319 FC / 3433 LUX
1196 FC / 12870 LUX
134 FC / 1440 LUX
1512 FC / 16280 LUX
78 FC / 842 LUX
311 FC / 3347 LUX
40 FC / 420 LUX
393 FC / 4230 LUX
36 FC / 392 LUX
141 FC / 1515 LUX
19 FC / 200 LUX
180 FC / 1933 LUX
10° Beam Angle
0 m
0 ft 1 m
3.28 ft
3 m
9.84 ft
2 m
6.56 ft
Ø 0.24 m / Ø 0.79 ft Ø 0.48 m / Ø 1.57 ft Ø 0.72 m / Ø 2.36 ft
Beam Diameter 10° Beam Angle

EPAR TRI Warranty
2-YEAR LIMITED WARRANTY
A. Elation Professionals®hereby warrants, to the original purchaser, Elation Profes-
sionals®products to be free of manufacturing defects in material and workmanship
for a period of two years (730 days) from the date of purchase. This warranty shall be
valid only if the product is purchased within the United States of America, including
possessions and territories. It is the owner’s responsibility to establish the date and
place of purchase by acceptable evidence, at the time service is sought.
B. For warranty service, send the product only to the Elation Professionals®factory.
All shipping charges must be pre-paid. If the requested repairs or service (including
parts replacement) are within the terms of this warranty, Elation Professionals®will
pay return shipping charges only to a designated point within the United States. If the
entire instrument is sent, it must be shipped in its original package. No accessories
should be shipped with the product. If any accessories are shipped with the product,
Elation Professionals®shall have no liability whatsoever for loss of or damage to any
such accessories, nor for the safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the prod-
uct is modied in any manner which Elation Professionals®concludes, after inspec-
tion, affects the reliability of the product; if the product has been repaired or serviced
by anyone other than the Elation Professionals®factory unless prior written authori-
zation was issued to purchaser by Elation Professionals®; if the product is damaged
because not properly maintained as set forth in the instruction manual.
D. This is not a service contract, and this warranty does not include maintenance,
cleaning or periodic check-up. During the period specied above, Elation Profession-
als®will replace defective parts at its expense, and will absorb all expenses for war-
ranty service and repair labor by reason of defects in material or workmanship. The
sole responsibility of Elation Professionals®under this warranty shall be limited to the
repair of the product, or replacement thereof, including parts, at the sole discretion
of Elation Professionals®. All products covered by this warranty were manufactured
after January 1, 1990, and bear identifying marks to that effect.
E. Elation Professionals®reserves the right to make changes in design and/or
improvements upon its products without any obligation to include these changes in
any products theretofore manufactured.
F. No warranty, whether expressed or implied, is given or made with respect to any
accessory supplied with products described above. Except to the extent prohibited
by applicable law, all implied warranties made by Elation Professionals®in connec-
tion with this product, including warranties of merchantability or tness, are limited in
duration to the warranty period set forth above. And no warranties, whether expressed
or implied, including warranties of merchantability or tness, shall apply to this prod-
uct after said period has expired. The consumer’s and or Dealer’s sole remedy shall
be such repair or replacement as is expressly provided above; and under no circum-
stances shall Elation Professionals®be liable for any loss or damage, direct or conse-
quential, arising out of the use of, or inability to use, this product.
G. This warranty is the only written warranty applicable to Elation Professionals®
Products and supersedes all prior warranties and written descriptions of warranty
terms and conditions heretofore published.
EPAR TRI Notes
Elation Professional - www.elationlighting.com - EPAR TRI Instruction Manual Page 18Elation Professional - www.elationlighting.com - EPAR TRI Instruction Manual Page 17

EPAR TRI Specifications
Model: EPAR TRI
SPECIFICATIONS:
Working Position: Any safe working position
Voltage: 100V ~ 240V/47~63Hz
LED’s: 14 x 1 Watt Tri LED’s (14 Red,
14 Blue, & 14 Green)
Power Consumption: 60.1W
Fuse: 2.5 Amp
Beam Angle: 10 Degrees
Weight: 9lbs./ 4.1Kgs.
Dimensions: 9.9” (L) x 8.5” (W) x 11” (H)
Colors: RGB Color Mixing
DMX Channels: 6 DMX Modes: 1 Channel Mode,
2 Channel Mode, 3 Channel Mode,
4 Channel Mode, 6 Channel Mode,
& 7 Channel Mode
Warranty: 2 Year (730 days)
Please Note: Specications and improvements in the design of
this unit and this manual are subject to change without any prior
written notice.
Auto Sensing Voltage: This xture contains a automatic voltage
switch, which will auto sense the voltage when it is plugged into
the power source.
©Elation Professionals®
A Division of the AmericanDJ® Group of Companies
World Headquarters:
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: [phone] Fax: [phone]
Web: www.elationlighting.com E-mail: [email protected]
American DJ Europe
Junostraat 2
6468 EW Kerkrade
Netherlands
[email protected] / www.americandj.eu
Tel: [phone] / Fax: [phone]
Elation Professional - www.elationlighting.com - EPAR TRI Instruction Manual Page 19