Elba BREEZA EH-C9041SL User manual

For The Warranty Terms & Conditions, Please Refer To Warranty Certificate.
Owner’s Manual
Please read this manual carefully before
operating your set.
Retain it for future reference.
Record model number and serial number
of the set.
See the label attached on the set and
quote this information to your dealer when
you require service.
ISLAND HOOD
MODEL: BREEZA EH-C9041SL(SS)

INSTALLATION INSTRUCTION
Fig.1
Fig.2 Fig.3
Fig.4 Fig.5

Fig.6 Fig.7
Fig.8 Fig.9

Fig.10 Fig.11
Fig.12 Fig.13
A B
Fig.14 Fig.15

GENERAL
Carefully read the following important information regarding installation safety and
maintenance. Keep this information booklet accessible for further consultations.
The appliance has been designed for use in the ducting version (air exhaust to the
outside –Fig.1B), filtering version (air circulation on the inside –Fig.1A) or with
external motor (Fig.1C) (not applicable to this model).
SAFETY PRECAUTION
1. Take care when the cooker hood is operating simultaneously with an open fireplace
or burner that depend on the air in the environment and are supplied by other than
electrical energy, as the cooker hood removes the air from the environment which a
burner or fireplace need for combustion. The negative pressure in the environment
must not exceed 4Pa (4x10-5 bar). Provide adequate ventilation in the environment
for a safe operation of the cooker hood.
Before connecting the model to the electricity network:
Check the rating plate located inside the appliance to ascertain the voltage and power
correspond to the electrical mains. Only install the appliance by qualified electrician.
WARNING !
In certain circumstances electrical appliances may be a danger hazard.
A) Do not check the status of the filters while the cooker hood is operating.
B) Do not touch bulbs or adjacent areas, during or straight after prolonged use of the
lighting.
C) Flambè cooking is prohibited underneath the cooker hood.
D) Avoid open flame, as it is damaging for the filters and a fire hazard.
E) Constantly check food frying to avoid that the overheated oil may become a fire
hazard.

F) Disconnect the electrical mains prior to any installation or maintenance.
G) This appliance is not intended for use by young children or infirm persons without
supervision.
H) Young children should be supervised to ensure they do not play with the appliance.
I) There shall be adequate ventilation of the room when the range hood is used at the
same time with appliances of burning gas or other fuels.
J) There is a risk of fire if cleaning is not carried out in accordance with the
instructions.
INSTALLATION INSTRUCTIONS
Assembly and electrical connections must be carried out by qualified technician.
• Electric Connection
The appliance has been manufactured as a class I, therefore earth cable is necessary.
Connect a plug for the appliance where necessary.
• The minimum distance between the support surfaces of the cooking pots on the
cooker top and the lowest part of the cooker hood must be at least 65 cm. If a
connection tube composed of two parts is used, the upper part must be placed outside
the lower part. Do not connect the cooker hood exhaust to the same conductor used to
circulate hot air or for evacuating fumes from other appliances generated by other than
an electrical source. Before proceeding with the assembly operations, remove the
anti-grease filter(s) (Fig.12) so that the unit is easier to handle. In the case of assembly
of the appliance in the suction version prepare the hole for evacuation of the air.

• Hood assembly
Remove the structure from the packaging and separate the upper part from the lower
part. Please pay attention that the arrow is positioned on the same side as the appliance
controls. Make 4 x Ø8 holes in the ceiling and drive in 3 screws without completely
tightening them (Fig2). Pay attention not to insert the screw into the hole marked with
an X on the hole template (the screws and expansion plugs must be suitable for the
type of wall).
- Take the upper part of the structure B and insert the 3 slots onto the 3 screws that are
not completely tightened. (Fig3) Rotate slightly to fit.
Drive in the fourth screw X and tighten the remaining 3 to allow definitive blocking of
the upper part of structure B. Take the lower part of the telescopic structure C and
insert it into the upper structure B.
-Adjust the height (Fig.5) by referring to the amounts indicated in and block it using
the 8 unit screws G that are supplied (Fig.4)
-Suction version: fix the flexible pipe to the prepared air evacuation hole (Fig.6).
-Take the upper chimney piece and fix it with 4 unit screws G. （Fig.7）
-Take the lower chimney and fix it with 2 unit screws G, drive in hood to avoid it
down .（Fig.8）
-Insert the suction unit inside the structure and set in 4 mounting hole, drive in 4 unit
screw N (Fig.9).
-Fix the air evacuation pipe H (not supplied) onto the connection flange (Fig.10)
-Unscrew the 2 screws G. and rest the lower chimney piece above the cooker hood
(Fig.11).
-If the cooker hood is supplied with a lower chimney piece that must be fixed to the
hood body with screws, remove the anti-grease filters from the hood by acting on
the relevant handles (Fig.12). Then screw the lower chimney piece pipe to the
inside of the hood, using screws P(Fig.13). Re-locate the filters in their seat.

USE AND MAINTENANCE
• It is recommended to operate the appliance prior to cooking.
Leave the appliance in operation for 10 minutes after cooking has completed in order
to completely eliminate cooking vapours and odours.
The proper function of the cooker hood is conditioned by the regularity of the
maintenance operations, in particular, the active carbon filter.
• The anti-grease filters capture the grease particles suspended in the air, and are
therefore subject to clogging according to the frequency of the use of the appliance.
In order to prevent fire hazard, it is recommendable to clean the filter at a maximum of
2 months by carrying out the following instructions:
- Remove the filters from the cooker hood and wash them in a solution of water and
neutral liquid detergent, leaving to soak.
- Rinse thoroughly with warm water and leave to dry.
- The filters may also be washed in the dishwasher.
The aluminum panels may alter in color after several washes. The manufacturer does
not hold any liability to replace or change as it is considered wear and tear accessory.
• The active carbon filters purify the air that is recycled to the environment. The filters
are not washable or reusable and must be replaced at maximum every four months.
The saturation of the active carbon filter depends on the frequency of use of the
appliance, by the type of cooking and the regularity of cleaning the antigrease filters.
(Fig.14) To remove the charcoal filters place your hand on one filter at a time and turn
it toward the front part. The charcoal filter can now be removed. Always ensure to
replace both filters at the same time.
• Clean the fan and other surfaces of the cooker hood regularly using a cloth moistened
with non-abrasive liquid detergent.

• The lamp illumination is designed to use during cooking and not for prolonged
general usage of the environment. Prolonged use of the lamp illumination notably
reduces the duration of the bulb. Use a one-edged screwdriver or any other appropriate
tool to lift and remove the overhead light fixture. Replace the damaged lamp. Use only
lamps as the original specification, avoiding contact with hands. Return the light
fixture to its position (snap fastening). (Fig. 15)
OPERATING INSTRUCTION:
(Figure 16)
A –Power On / Off
B –Timer On / Off
C –Speed Settings / Time Display
D –Sliding Touch Control
E –Motor, automatic on / off
F –Lamps On / Off
1) Press A to Power on and the A key indicator will lights. Then all button will
enter standby mode.
2) Press the B key, the motor is the most low start, and the default time of 15
minutes, stop the clock display flashes can change to stop the clock time sliding
touch D and C display ( display every five minutes), after 3 seconds, the B key

indicator flashes, most low-grade to enter the timing the motor stops running,
sliding touch D to change the motor stalls and C display, full The grid for stir
gear, when the motor running in the a stir gear, C the last two frames on the
display flashes.
3) If you press the E key, the motor is the most low start sliding touch D to change
the motor stalls, and C on the display shows the full grid stir files, when the
motor is running in the file of the stir, C the last two frames on the display
flashes.
(Note: This product is the default the stir files can only run 150 seconds, after
running automatically downshift.)
4) When the motor is running, press the B button, B button indicator lights and C
screen starts flashing, you can change to stop the clock time sliding touch D and
C display (display every five minutes), 3 seconds after, B indicator flashes, the
motor into the timing to stop running; To cancel this function, press the B button
again.
5) When the F key is pressed, the indicator light lighting lights; then press the F
key, lighting the lamp.

TROUBLESHOOTING
Problem
Possible reason
Solution
Hood doesn’t work
No electric supply
Check the plug is connected
Check the main switch is turned on
Poor airflow
Metal grease filters
clogged
Clean the filters and replace when
dry
Charcoal filters
clogged
Replace the charcoal filters
Motor running but no
air flow
Butterfly valve jammed
Contact technician
Motor cuts after a
few minutes
High temperature
safety device activated
The kitchen is not sufficiently
ventilated
The hood is installed
too near the cooking
stove
The hood must be least 65cm from
stove
Strong cooking smell
Charcoal filters not
installed
In re-circulating mode, charcoal
filters must be installed
Oil dripping onto
stove
Oil cup missing or not
installed
Remove aluminum filter and
replace oil cup
Aluminum grease filter
saturated
Wash the aluminum grease filters
Whirring sound
Something in contact
with fan blade
Contact with technician
THE MANUFACTURE DECLINES ALL RESPONSIBILITY FOR EVENTUAL
DAMAGES CAUSED BY BREACHING THE ABOVE WARNINGS.
MAIN SPECIFICATION
Rated Voltage : 220-240V/50Hz
Light : 1W x 4
Suction Power : 1,400m³/hr
Motor Power : 320W
Product Dimension : 900mm(W) x 595-995mm(H) x 515mm(D)

Correct Disposal of this product:
This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible
harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of
material resources. To return your used device, please use the return and collection systems or contact the retailer where the product
was purchased. They can take this product for environmental safe recycling.