Elba EH-M9138ST User manual

For The Warranty Terms & Conditions, Please Refer To Warranty Certificate
Owner’s Manual
Please read this manual carefully
before operating your set.
Retain it for future reference.
Record model number and serial
number of the set.
See the label attached on the set and
quote this information to your dealer
when you require service.
DESIGNER HOOD
MODEL: EH-M9138ST(BK)

1
Please read this instruction carefully. It is advisable to keep this instruction
manual in a safe place for future reference.
SAFETY PRECAUTIONS
1. Keep electrical appliances out of reach from children. Do not let them to operate the
appliances without supervision.
2. To protect against the risk of electrical shock, do not immerse the product, power cord
or plug into water or any other liquid.
3. This product is for household and indoor use only.
4. This product is not intended for use by person (including children) with reduced
physical, sensory or mental capabilities unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety.
5. If the power cord or plug is damaged, it must be replaced by the service centre or a
qualified service technician to avoid hazard.
6. Before installation, check if the mains supply voltage is matched with the voltage
stated on the rating plate of the cooker hood.
7. There must be adequate air ventilation of the room when the cooker hood is used with
the cooking appliances with burning gas or other fuels.
8. Ensure that the installation of exhaust complies with the standard of local building, gas
and electrical authorities.
9. Do not ignite flames in the pans.
10. There is a risk of fire if cleaning is not carried out in accordance with this instruction.

2
ASSEMBLY INSTRUCTIONS
Please check the following before installation:
•Installation of cooker hood must be carried out by an authorized or qualified technician.
•Remove all packaging materials from the cooker hood. Check and make sure that the
cooker hood is not damaged.
•Please ensure the power supply has switched OFF when installing the cooker hood.
•For optimum air extraction, avoid having too many windows surrounding the cooker
hood which will cause air convection.
•The optimum height for the installation is between 400 to 450mm which is measured
from the bottom of the cooker hood to the top of the hob.
•Make sure the hood is in level after installation to avoid oil spill over from the oil cup.
•Before installing, determine the height between the bottoms of the cooker hood to the
top of the hob. Mark on the wall to suit the bracket locations.
•Drill holes with diameter of Ø10mm. Insert the screw anchors into the holes. Fix the
mounting bracket and tighten the screws.

3
•Hang the cooker hood on the mounting bracket and make sure the cooker hood is in
level.
•Fix the exhaust ducting on the cooker hood. Install the oil cup on the cooker hood.
•Install the exhaust cover to the height required.
•Pull the upper exhaust cover upwards then install the fixing bracket to fix the exhaust
cover position.
•Drill 2 holes with diameter of Ø8mm. Insert the screw anchors into the holes. Fix the
mounting bracket and tighten the screws.
•Before connecting to the mains supply, ensure that the mains voltage corresponds to
the voltage on the rating plate of the cooker hood.

4
NOTE: In order to ensure the well ventilation of Cool Breeze function, please
ensure there is at least 30mm gap for ventilation.
INSTALL THE CHARCOAL FILTER
•Disconnect the power supply. Gently push the clip on the grease filter to eject and use
both hands to remove it carefully (Please do not open while the cooker hood is operate
or connecting the power supply).

5
•On the left side, install the charcoal filter and lock the position by turning anti-clockwise
direction to tighten.
•On the right side, Install the charcoal filter and lock the position by turning clockwise
direction to tighten.
•To remove the charcoal filter, reverse the direction on above direction to loosen.

6
PRODUCT DESCRIPTIONS
1 Cool Breeze –Press to activate the Cool Breeze function while cooking. The cooling
fan will turn on. Press again to turn off this function.
2 Blue Magic Light –Press to turn on the Blue Magic Light. Press again to turn off.
3 High Speed Control –Press to operate cooker hood in high fan speed. Press and hold
for 4 seconds to activate the heat cleaning function. Press and hold again to
deactivate (please refer to Heat Cleaning Function).
4 Low / Medium Speed Control –Press to operate cooker hood in low fan speed and
press again to operate cooker hood in medium fan speed.
5 Press this button during operation to schedule one minute delay timer to turn off the
cooker hood. Press again to turn off immediately.
6 Gesture Motion Sensor –Wave your hand from left to right to turn on the cooker hood.
The cooker hood will start to operate with high fan speed and LED light will turn on.
Wave your hand from right to left to turn off the cooker hood. The cooker hood will stop
operate and turn off immediately.
NOTE: The ideally gesture motion speed from left to right or right to left shall
within two seconds. The ideally distance of gesture motion from control panel is
from 5 –10CM.
6
1
2
3
4
5
6

7
OPERATING INSTRUCTIONS
1 Press the button and press the button to operate the cooker hood in low fan
speed. Press the button again to operate the cooker hood at medium fan speed.
Press the button to operate the cooker hood at high fan speed.
2 When the motor is running in low, medium or high fan speed, press button to
schedule one minute delay timer to turn off the cooker hood. Cooker hood will be
turned off after one minute. Press button again when the cooker hood is in delay off
timer to turn off cooker hood.
3 Press the button to turn on the Blue Magic Light. Press again to turn off. (This
function does not relate to the cooker hood motor).
NOTE: When the cooker hood is operating, do not perform any of the maintenance
or service the cooker hood. Avoid touching the inside of the cooker hood to avoid
hazard.
HEAT CLEANING FUNCTION
1 Press and hold the button for 4 seconds to activate the heat cleaning function.
2 The cooker hood will operate the heat cleaning function for 15 minutes.
3 The indicator light will keep blinking, heat cleaning process will start and run for 14
minutes. After that cooker hood will stop for the heating function and operate for final
cool down.
4 The final cool down process will operate for 1 minute. The cooker hood will be running
in high fan speed for final cool down process and turn off the cooker hood upon
completed.
5 Press and hold the button to deactivate the heat cleaning function or press the
button to deactivate.
NOTE: During the heat cleaning process, only button or ON/OFF button can be
functional.

8
CLEANING AND MAINTENANCE
•The cooker hood must always be disconnected from the electricity supply before
carrying out any maintenance.
•Clean the cooker hood with damp cloth, hot water and mild detergent. Do not use
chemical, steel, wooden or abrasive cleaners to clean the cooker hood.
•Remove the oil cup in horizontal direction, wash in hot soapy water, dry and fit back
into the cooker hood. Do not use the cooker hood without the oil cup installed.
•Avoid spilling water into the motor and electronic component.
CLEANING THE GREASE FILTER AND OIL CUP
•Disconnect the power supply. Gently push the clip on the grease filter to eject and use
both hands to remove it carefully.
•Remove the oil cup on the motor for cleaning.
•Clean the grease filter with household cleaning detergent to ensure the filters are free
from dirt (clean the filter once every month).
•After cleaning, install back the oil cup to its original position and put the grease filter in
place.

9
TROUBLESHOOTING
Malfunctions
Possible Root Cause
Checking
Weak Suction
The distance is too far between
the cooker hood and cooking
appliance
Lower down the cooker hood
installation height but within the safety
guideline
Strong convection due to too
much ventilation
Shut off some of the windows or doors
Cooker hood and light
not function
The power supply is not
connected
Check if the plug is well connected
and the power is on
Power cord is damaged
Contact technicians for repair
Motor functions but
light not works
Light bulb is damaged
Contact technicians to replace a new
light bulb
Light works but motor
not function
The bearing may be damaged
Contact technicians for repair
The internal wires or motor
capacitor may be burnout
Vibration on the cooker
hood
The screw is loosen
Tighten the screws
The cooker hood is
noisy
Exhaust pipe surface is distorted
Contact technicians to reinstall the
exhaust pipe