Elba EH-J9031ST(SS) User manual

For The Warranty Terms & Conditions, Please Refer To Warranty Certificate
Owner’s Manual
Please read this manual carefully
before operating your set.
Retain it for future reference.
Record model number and serial
number of the set.
See the label attached on the set and
quote this information to your dealer
when you require service.
DESIGNER HOOD
MODEL: EH-J9031ST(SS)
EH-J9032ST(BK)

Please read this instruction carefully. It is advisable to keep this instruction
manual in a safe place for future reference.
SAFETY PRECAUTIONS
1. Keep electrical appliances out of reach from children. Do not let them to
operate the appliances without supervision.
2. To protect against the risk of electrical shock, do not immerse the product,
power cord or plug into water or any other liquid.
3. This product is for household and indoor use only.
4. This product is not intended for use by person (including children) with
reduced physical, sensory or mental capabilities unless they have been
given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
5. If the power cord or plug is damaged, it must be replaced by the service
centre or a qualified service technician to avoid hazard.
6. Before installation, check if the mains supply voltage is matched with the
voltage stated on the rating plate of the cooker hood.
7. There must be adequate air ventilation of the room when the cooker hood
is used with the cooking appliances with burning gas or other fuels.
8. Ensure that the installation of exhaust complies with the standard of local
building, gas and electrical authorities.
9. Do not ignite flames in the pans.
10.There is a risk of fire if cleaning is not carried out in accordance with this
instruction.
1

ASSEMBLY INSTRUCTIONS
Please check the following before installation:
Installation of cooker hood must be carried out by an authorized or qualified
technician.
Remove all packaging materials from the cooker hood. Check and make sure
that the cooker hood is not damaged.
Please ensure the power supply has switched OFF when installing the cooker
hood.
For optimum air extraction, avoid having too many windows surrounding the
cooker hood which will cause air convection.
The optimum height for the installation is between 650 to 750mm which is
measured from the bottom of the cooker hood to the top of the hob.
Make sure the hood is in level after installation to avoid oil spill over from the oil
cup.
Before installing, determine the height between the bottoms of the cooker hood
to the top of the hob. Mark on the wall to suit the bracket locations.
Drill 3 holes with diameter of Ø8mm. Insert the screw anchors into the holes. Fix
the mounting bracket and tighten the screws.
2

Hang the cooker hood on the mounting bracket and make sure the cooker hood
is in level.
Fix the exhaust ducting on the cooker hood. Install the oil cup on the cooker
hood.
Install the exhaust cover to the height required.
Pull the upper exhaust cover upwards then install the fixing bracket to fix the
exhaust cover position.
3

Drill 2 holes with diameter of Ø8mm. Insert the screw anchors into the holes. Fix
the mounting bracket and tighten the screws.
Before connecting to the mains supply, ensure that the mains voltage
corresponds to the voltage on the rating plate of the cooker hood.
INSTALL THE CHARCOAL FILTER
Disconnect the power supply and then remove the baffle filter.
Install the charcoal filter and lock the position by turning anti-clockwise direction
to tighten.
To remove the charcoal filter, turn clockwise direction to loosen.
There are two charcoal filters provided and install on the left and right position.
4

PRODUCT DESCRIPTIONS
1 Heat Cleaning –Press to activate the heat cleaning function. Press again to
deactivate the heat cleaning function.
2 Off / Low Fan Speed Control –Press to turn off the cooker hood or decrease
the fan speed.
3 Digital Display –Display for current fan speed “1”, “2”, “3”, and “4”.
4 On / High Fan Speed Control –Press to turn on the cooker hood or increase
the fan speed.
5 LED Light Illumination –Press to turn on the LED light. Press again to turn off
the LED light.
OPERATING INSTRUCTIONS
1 Press the button to start and operate the cooker hood in normal fan
speed. Press the button to operate the cooker hood at higher fan speed.
2 When the motor is running in normal or high fan speed, press button to
lower down the cooker hood fan speed. Press button until the end will turn
off the cooker hood. (This function does not relate to the LED light
illumination)
3 When the motor is running in normal or high fan speed, press and
together to schedule the cooker hood to turn off after five minutes. Digital
display will flashing and turn into countdown mode. Cooker hood will be
turned off after five minutes. Press and together button again to
deactivate this function.
4 Press the button to turn on the LED light. Press button again to turn off.
(This function does not relate to the cooker hood motor)
5

HEAT CLEANING FUNCTION
1 Press and hold the button for 3 seconds to activate the heat cleaning
function.
2 The cooker hood will operate the heat cleaning function for 7 minutes.
3 The heat cleaning will start cleaning and running for 5 minutes, after that
cooker hood will stop for the heating function and turn on the lower fan speed
for final cool down.
4 The final cool down process will operate for 2 minutes and will turn off the
cooker hood upon completed.
5 Press the button to deactivate the heat cleaning function.
CLEANING AND MAINTENANCE
The cooker hood must always be disconnected from the electricity supply before
carrying out any maintenance.
Clean the cooker hood with damp cloth, hot water and mild detergent. Do not
use chemical, steel, wooden or abrasive cleaners to clean the cooker hood.
Remove the oil cup in horizontal direction, wash in hot soapy water, dry and fit
back into the cooker hood. Do not use the cooker hood without the oil cup
installed.
Avoid spilling water into the motor and electronic component.
CLEANING THE BAFFLE FILTER INNER OIL CUP
Disconnect the power supply and then gently push the clip on the baffle filter to
eject and use both hands to remove it carefully.
Remove the oil cup on the motor for cleaning.
Clean the baffle filter with household cleaning detergent to ensure the filters are
free from dirt (clean the filter once every month).
After cleaning, install back the oil cup to its original position and put the baffle
filter in place.
6

TROUBLESHOOTING
Malfunctions
Possible Root Cause
Checking
Weak Suction
The distance is too far between
the cooker hood and cooking
appliance
Lower down the cooker hood
installation height but within the safety
guideline
Strong convection due to too
much ventilation
Shut off some of the windows or
doors
Cooker hood and light
not function
The power supply is not
connected
Check if the plug is well connected
and the power is on
Power cord is damaged
Contact technicians for repair
Motor functions but
light not works
Light bulb is damaged
Contact technicians to replace a new
light bulb
Light works but motor
not function
The bearing may be damaged
Contact technicians for repair
The internal wires or motor
capacitor may be burnout
Vibration on the
cooker hood
The screw is loosen
Tighten the screws
The cooker hood is
noisy
Exhaust pipe surface is distorted
Contact technicians to reinstall the
exhaust pipe
7

MAIN SPECIFICATION
Rated Voltage : 220-240V/50Hz
LED Light : 8W x 1
Suction Power : 1,400m³/hr
Motor Power : 270W
Product Dimension : 900mm (W) x 548-1,000mm (H) x 505mm (D)
PRODUCT SIZE
NOTICE
This product must not be disposed together with domestic waste. It has to be disposed at an
authorized place for recycling of electrical and electronic appliances. By collecting and recycling
waste, you help to save natural resources and make sure the product is disposed in an
environmental friendly and healthy way.
8