Elba EH-N9128ST User manual

For The Warranty Terms & Conditions, Please Refer To Warranty Certificate
Owner’s Manual
Please read this manual carefully
before operating your set.
Retain it for future reference.
Record model number and serial
number of the set.
See the label attached on the set and
quote this information to your dealer
when you require service.
DESIGNER HOOD
MODEL: EH-N9128ST(BK)

Please read this instruction carefully. It is advisable to keep this instruction
manual in a safe place for future reference.
SAFETY PRECAUTIONS
1. Keep electrical appliances out of reach from children. Do not let them to
operate the appliances without supervision.
2. To protect against the risk of electrical shock, do not immerse the product,
power cord or plug into water or any other liquid.
3. This product is for household and indoor use only.
4. This product is not intended for use by person (including children) with
reduced physical, sensory or mental capabilities unless they have been
given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
5. If the power cord or plug is damaged, it must be replaced by the service
centre or a qualified service technician to avoid hazard.
6. Before installation, check if the mains supply voltage is matched with the
voltage stated on the rating plate of the cooker hood.
7. There must be adequate air ventilation of the room when the cooker hood
is used with the cooking appliances with burning gas or other fuels.
8. Ensure that the installation of exhaust complies with the standard of local
building, gas and electrical authorities.
9. Do not ignite flames in the pans.
10.There is a risk of fire if cleaning is not carried out in accordance with this
instruction.

ASSEMBLY INSTRUCTIONS
Please check the following before installation:
•Installation of cooker hood must be carried out by an authorized or qualified
technician.
•Remove all packaging materials from the cooker hood. Check and make sure
that the cooker hood is not damaged.
•Please ensure the power supply has switched OFF when installing the cooker
hood.
•For optimum air extraction, avoid having too many windows surrounding the
cooker hood which will cause air convection.
•The optimum height for the installation is between 350 to 400mm which is
measured from the bottom of the cooker hood to the top of the hob.
•Make sure the hood is in level after installation to avoid oil spill over from the oil
cup.
•Before installing, determine the height between the bottom of the cooker hood
to the top of the hob. Mark on the wall to suit the bracket locations.

•Drill 4 holes with diameter of Ø8mm and 60mm deep. Insert the screw anchors
into the holes. Fix the mounting bracket and tighten the screws.
•Remove the horizontal oil cup. Hang the cooker hood on the mounting bracket
and make sure the cooker hood is in level.
•Fix the exhaust ducting on the cooker hood. Install the oil cup on the cooker
hood.
•Install the telescopic exhaust cover to the height required.
•Before connecting to the mains supply, ensure that the mains voltage
corresponds to the voltage on the rating plate of the cooker hood.
INSTALL THE CHARCOAL FILTER
•Press the button and press the button to open the cover.
•Once the cover is opened, disconnect the power supply. Remove the oil cup
and flip the bottom glass panel downward.

•Loosen two screws and remove the filter.
•Loosen two screws around the air inlet ring and install the charcoal filter.
•After that, install the parts according to the steps mentioned above.

PRODUCT DESCRIPTIONS
1 Switch/Delay Off Function –To switch the cooker hood to standby mode and
turn off the cooker hood. Press this button during operation to schedule three
minute delay timer to turn off the cooker hood.
2 Low Fan Speed –To operate at low fan speed.
3 High Fan Speed –To operate at high fan speed.
4 Turbo Fan Speed –Press this button to operate at turbo fan speed for three
minute (after three minute will revert to high fan speed).
5 LED Light Illumination –To switch on/off the LED light.
6 Gesture Motion Sensor –Wave your hand from left to right to turn on the
cooker hood. The cooker hood will start to operate with high fan speed.
Continue wave your hand in same direction to switch to turbo fan speed.
Wave your hand from right to left to activate delay off function. Wave your
hand in same direction again to turn off cooker hood completely.
NOTE: The ideally gesture motion speed from left to right or right to left
shall within two seconds. The ideally distance of gesture motion from
control panel is from 5 –10CM.

OPERATING INSTRUCTIONS
1 Press the button and press the button to operate the cooker hood in
low speed. Press the button to operate the cooker hood in high speed.
Press the button to operate the cooker hood in turbo speed. This
function will revert to high speed after three minute.
2 When the motor is running in normal or high fan speed, press button to
schedule the cooker hood to turn off after three minutes. Cooker hood will be
turn off after three minutes. Press button again when the cooker hood in
delay off mode to turn off the cooker hood immediately.
3 Press the button to turn on the LED lamp. Press again to turn off. (This
function does not relate to the cooker hood motor).

CLEANING AND MAINTENANCE
•The cooker hood must always be disconnected from the electricity supply
before carrying out the maintenance.
•Clean the cooker hood with damp cloth, hot water and mild detergent. Do not
use chemical, steel, wooden or abrasive cleaners to clean the cooker hood.
•Remove the oil cup in horizontal direction, wash in hot soapy water, dry and fit
back into the cooker hood. Do not use the cooker hood without the oil cup
installed.
•Avoid spilling water into the motor and electronic component.
CLEANING THE INNER PART
•Press the button and press the button to open the cover.
•Once the cover is opened, disconnect the power supply. Remove the oil cup
and flip the bottom glass panel downward.
•Loosen two screws and remove the filter.

•Loosen the screws on the charcoal filter and then take it out.
•Loosen the screws on the air inlet ring and then take it out.
•Turn the locking nut in clockwise direction to take out the impeller for cleaning.
•After the maintenance, install the parts according to the steps mentioned above.
REPLACING THE LIGHT BULB
•Disconnect the power supply, slightly insert the screwdriver at the edge of the
LED light and pry downward to take out the LED light (4W).
•Disconnect the connecting cable of LED light (4W) and replace a new LED light
unit (4W). Connect the power supply to ensure LED light (4W) is functioning.
※The LED light bulb shall not be greater than 4W.

TROUBLESHOOTING
Malfunctions
Possible Root Cause
Checking
Weak Suction
The distance is too far between
the cooker hood and cooking
appliance
Lower down the cooker hood
installation height but within the safety
guideline
Strong convection due to too
much ventilation
Shut off some of the windows or doors
Cooker hood and light
not function
The power supply is not
connected
Check if the plug is well connected
and the power is on
Power cord is damaged
Contact technicians for repair
Motor functions but
light not works
Light bulb is damaged
Replace a new light bulb ( 4W)
Light works but motor
not function
The bearing may be damaged
Contact technicians for repair
The internal wires or motor
capacitor may be burnout
Vibration on the cooker
hood
The screw is loosen
Tighten the screws
The cooker hood is
noisy
Exhaust pipe surface is distorted
Contact technicians to reinstall the
exhaust pipe