Eldat Easywave Neo STH01 User manual

STH01 Temperature humidity sensor Format 55
EN
Model
Technical details
Frequency: 868.30 MHz
Radiated power: 0.41 mW
Modulation: FSK
Coding: Easywave neo
Range:
under free eld
conditions approx. 150 m
in the building approx. 30 m
Power supply: 2x 3 V-battery, CR2032
Current consumption: max. 20 mA
Standby current: approx. 1.1 µA
Measuring range: 1-99% rF
Accuracy: ±5% (at 30% - 70% rF)
Measuring range
temperature: 0 °C bis +60 °C ±1 °C
Recording the every 10 min or at
measured values: button operation
Operating temperature: -20 °C to +60 °C
Dimensions: Format 55
Cover (L/W/H) 55/55/9 mm
Plate (L/W/H) 71/71/1.5 mm
Weight: 34 g
Scope of delivery
Transmission module, 2 batteries CR2032,
mounting plate, attachment set,
operating instructions
STH01EN5001A01
A
E
F
B1
D
G
C
PTx
B2
C
C
3
3
2
2
A Button
B1 Transmission module front
B2 Transmission module back
PTx Learning button
C Battery CR2032
D Cover frame
(Not in the delivery)
E Mounting plate
F Catches
G Transmission LED
Function
The temperature humidity sensor STH01 mea-
sures the temperature and relative humidity cy-
clically and sends these values to a compatible
ELDAT Smarthome-Server APC01.
After inserting the battery, the sensor is immedia-
tely ready for operation and the current measured
values are transmitted via radio telegram.
After the last transmission, the current values are
automatically transmitted every 10 minutes.
The current values can be transmitted manually
by pressing the front area of the button.
During each transmission, the transmission LED
lights up briey.
The STH01 ts into the most switch frames with
the dimensions of 55x55 mm.
Start-Up
1. Screw or stick the mounting plate to the instal-
lation site.
Attention! Make sure there is no interference
with the wireless connection. Do not mount
the device in a distribution box, in metal cas-
ings, in direct proximity to large metal objects,
on the oor or close to it.
2. Insert the batterie (C) in the transmission mo-
dule (B2). The positive pole has to be visible!
3. Place the cover frame (D) onto the mounting
plate (E) and snap the transmission module
(B) to the catches (F) on top and bottom. The
arrow on the sensor module has to point up-
wards.
4. Snap the button (A) onto the transmission
module (B).
Programming the transmission code
into the receiver
To program the sensor into the Smarthome ser-
ver, please follow the instructions given in the
app.
As soon as you are prompted to do so, press the
rear learning button PTx to send the program-
ming telegram.
You can then press the front button (A) to trans-
mit the current measured values.
gure 1
transmission
LED
Please read the operating instructions
carefully before using the device!
Also read the operating instructions for the de-
vices to be controlled!
Do not modify the devices!
Have faulty hand transmitters checked by the
manufacturer!
Keep the batteries away from children!
Intended use
The radio sensor may only be used to measure
the ambient temperature and humidity to operate
smart home server.
The manufacturer shall not be liable for any da-
mage caused by improper or non-intended use!
Safety instructions

General information
Disposal
Waste electronic equipment must not be
disposed of with household waste!
Dispose of the waste product via collec-
tion facilities for electronic scrap or via
your specialist dealer.
Dispose of used batteries in a recyc-
ling bin for batteries or via the specialist
trade.
Dispose of packaging material in the
recycling bins for cardboard, paper and
plastic.
Warranty
Within the statutory warranty period we undertake
to rectify free of charge by repair or replacement
any product defects arising from material or pro-
duction faults. Any unauthorized tampering with,
or modications to, the product shall render this
warranty null and void.
Conformity
Hereby, ELDAT EaS GmbH declares that the ra-
dio equipment type STH01 is in compliance with
Directive 2014/53/EU. The full text of the EU de-
claration of conformity is available at the following
internet address: www.eldat.de
Customer service
If the device does not work properly despite pro-
per handling or in case of damage, please contact
the manufacturer or your retailer.
ELDAT EaS GmbH
Im Gewerbepark 14
15711 Königs Wusterhausen
Germany
Phone: + 49 (0) 33 75 / 90 37-310
Fax: + 49 (0) 33 75 / 90 37-90
Internet: www.eldat.de
E-mail: [email protected]
UM159946A 0621 EN
Battery check
The transmitter has a battery check function,
which checks the capacity of the battery during
the transmission process.
If the capacity of the battery is low, the transmis-
sion LED ashes every 10 minutes for 3 seconds
and a data telegram is transmit.
Replace the batteries as soon as possible.
Replacing the Battery
1. Lever o󰀨 the transmission group.
2. Replace the battery. Only use batteries of the
type CR2032. Make sure the poling is correct.
The positive pole has to be visible!
3. Replace the transmission group back onto
the catches.
Hinweis: The coding of the transmiter is preser-
ved even if there is no voltage supply.You do not
need to memorize the code in the recei vers again
after a battery change.
TroubleShooting
If the radio control does not react to the STH01:
- Exchange the battery..
- Check that the wireless connection at the
installation site is not impaired between the
STH01 and the receiver.
- Program the transmission code in the recei-
ver.
- Other wireless devices using the same fre-
quency or working in direct proximity may
interfere with the device.