Eldat RTS26 User manual

E
F
H
G
43 mm
10 mm
Ø
Model
RTS26E5001-01
Technical Details
Frequency: 868.30 MHz
Radiated power: 0.34 mW
Modulation: FSK
Coding: Easywave
Power supply: 1x 3-V-battery, CR2032
Operating temperature: -20 °C up to +60 °C
Range: free-eld: approx. 150 m
buildings: approx. 30 m
Dimensions (w/l/h): 33/166/8 mm
Weight: 34.0 g (incl. battery)
Scope of Delivery
Window handle contact RTS26 ALARM,
magnetic disc, battery holder, battery CR2032,
operating instruction
Intended Use
Only use the window handle contact RTS26
ALARM to transmit radio signals to the Radio
Alarm Annunciator RTRP02.
The manufacturer shall not be liable for any da-
mage caused by improper or non-intended use.
Safety Advice
Before using the device, carefully read
through the operating instructions!
Also note the operating instructions of the
receiver(s)!
Please check regularly the ready-to-transmit-
state of the device!
Have faulty devices checked by the manufactu-
rer!
Do not make any unauthorized alterations or
modications to the device-!
Keep the batteries out of the reach of children!
RTS26 Radio Window Handle Contact ALARM
GB
Funktion
The window handle contact RTS26 ALARM is a
magnetic contact that signals the open/closed
status of a window acoustically and transmits an
alarm telegram wireless to the radio alarm annun-
ciator RTRP02.
If a window is opened while the window handle
contact is activated, a warning signal sounds for
approx. 1.5 minutes. You can deactivate this by
pressing the button for some time. Once the win-
dow is closed, the window handle contact activa-
tes itself automatically after 10 seconds.
The window handle contact is suited for standard
window handles with a rod dimension of 7 mm,
screw dimension of 10 mm and a hole spacing
of 43 mm.
Start-Up
1. Insert the enclosed battery into the battery
holder and put these into the RTS26.
Use only batteries of type CR2032. Make
sure the polarity is correct. The positive pole
has to be visible! (g. 1)
2. Unscrew the window handle while the window
is closed. Remove the protective foil from the
rear adhesive pad of the window handle con-
tact and stick this onto the window frame.
Observe the correct position (the drill holes
must be vertically aligned). (g. 2)
3. Insert the magnetic disc in the window handle
contact. The magnet must point to the reed
contact. (g. 2)
4. Move the window handle through the magne-
tic disc back into the window and screw the
handle on again. (g. 2)
5. With the windows closed, press the button
until the LED briey blinks red. Now the win-
dow handle contact is activated. (g. 1)
6. Memorize the transmission code in to the
RTRP02. Please read the operating inst-
ructions supplied with the alarm annuciator.
Open the window briey, the Easywave code
A is transmitted to the alarm annuciator, the
LED on RTS26 illuminated in red and the
transmission code has been learned.
Handle Contact Activate / Deactivate
Press sequentially the button to activate or deac-
tivate the window handle contact.
D
B
A
C
DeactivatedActivated
RED
GREEN
Press the button,
the LED light up
red.
Press the button,
the LED light up
green.
g. 1
g. 2
ABattery holder with
battery CR2032
BMagnetic disc
CButton and LED green/red
DAlarm annuciator RTRP02
EMagnet
FReed contact
G Square bar max. 7 mm
H Protective lm from the
adhesive pad

Status Indication
If the window handle is twisted while the win-
dow handle contact is activated, a warning beep
sounds for approx. 1.5 minutes. After this, the win-
dow handle contact is deactivated automatically.
To shut o󰀨 the warning beep, keep the button
pressed until the beep has nally stopped.
Attention: Now the window handle is deactivated
and can be reactivated manually immediately af-
ter closing the window or automatically after 10
seconds..
UM92181B 1017 GB
Diposal
Waste electrical products and batteries may
not be disposed with household waste!
Dispose the waste product via a collec-
tion point for electronic scrap or via your
specialist dealer.
Dispose used batteries in a recycling bin
for batteries or via the specialist trade.
Put the packaging material into the
recycling bins for cardboard, paper and
plastics.
Warranty
Within the statutory warranty period we undertake
to rectify free of charge by repair or replacement
any product defects arising from material or pro-
duction faults.
Any unauthorized tampering with, or modications
to, the product shall render this warranty null and
void.
Conformity
Hereby, ELDAT GmbH declares that the radio
equipment type RTS26 is in compliance with
Directive 2014/53/EU.
The full text of the EU declaration of conformity is
available at the following internet address:
www.eldat.de
Service
If, despite correct handling, faults or malfunctions
occur or if the product was damaged, please con-
tact your retailer or the manufacturer.
ELDAT GmbH
Im Gewerbepark 14
15711 Königs Wusterhausen
Germany
Phone: + 49 (0) 33 75 / 90 37-310
Fax: + 49 (0) 33 75 / 90 37-90
Internet: www.eldat.de
E-Mail: [email protected]
Battery Check
The battery voltage is monitored cyclically. Once
the battery is discharged, the red LED briey
blinks red 2x at an interval of approx. 10 seconds.
Please exchange the battery now (see section
„Start-up“).
An undervoltage telegram is also sent. This can
be evaluated by the alarm signaller RTRP02.
If the voltage drops further, the window handle
contact deactivates itself. An alarm will no longer
be sent in this case.
Trouble Shooting
If the alarm annuciator does not react to the trans-
mitter:
- Exchange the battery of the RTS26 or make
sure that the polarity of the battery is correct.
- Check that the wireless connection at the
installation site is not impaired between the
transmitter and the alarm annuciator.
- Teach the transmission code to the receiver
again.
- Other wireless devices using the same fre-
quency or working in direct proximity may in-
terfere with the device.
Signal tone
approx.
1.5 min