Electrolux E36GC65ESS - 30"""" Drop-in Gas Cooktop User manual

Installation Instructions
Cooktop
L_Electrolux

IMPORTANTSAFETYINSTRUCTIONS
NiNllNmiNiHNNHNnaNNilN
SafetyPrecautions
Do not attempt to install or operate your unit until you have read the safety
precautions in this manual. Safety items throughout this manual are labeled with a
Warning or Caution based on the risk type.
Definitions
This is the safety alert symbol. It is used to alert you to potential personal injury
hazards. Obey all safety messages that follow this symbol to avoid possible injury
or death.
iiiii!!!ili_
i!iiiiiilill

Safety
SAFETYPRECAUTIONS

Safety
ililili!iii!
ii_i_iiiiii
_!iiiiiiiiiiii
iiiiiiii!iii!i
ili!ii!iiiiii!i
!!ili!!!iii!
iii_iiii!i_iii
_iiii!iiiiiiiili_
i!!iiiiiiii!ii
iiii!i!iiiiiiiii
!iii!i!!!!_ill
iiiiiii,_!iiiilili
iiiii!]iiiiii
i!iiiii!!iii_
iiiiiiiiiii!i_
iiiii!ii!!iiiiiii
!_iii!ii_iil
i_iiii!ii_
:Y:2:2P_S
iiiiiiiii_iiiiiii!_iiii!i!i

Finding Information
READANDSAVETHESEINSTRUCTIONS
mmmmmmmmmmmmmmmmmmmmmm
))
Read all instructions before installing the cooktop.
For your safety, please read and observe all safety instructions. This guide will help
you anticipate all installation connections.
QUESTIONS?
mmmmmumtmBmmmmmmtmmmmm
For toll-free telephone support in the U.S. and Canada:
1-877- 4ELECTROLUX (1-877-435-3287)
For online support and Internet product information:
www.electroluxusa.com
_2005 Electrolux Home Products,Inc.
Post Office Box 212378, Augusta, Georgia 30917, USA
All rights reserved. Printed in the USA

Finding Information
TABLEOFCONTENTS
mmmmmmmmmmmmmmmmnmmmmm
Safety...................................................................2
OeffniUons..........................................................2
ImportantSafetyInstructions.............................. 2
SafetyPrecautions.............................................3
FindingInformation...........................................5
PleaseReadAndSaveThisGuide...................5
Questions?........................................................5
TableOfContents..............................................6
Preparingfor Installation..................................7
VerifyingPackageContents...............................7
CabineVCounteropPreparation.........................7
MakingtheGas/ElectricConnection..............10
Requirements..................................................10
Installation........................................................12
InstallingtheCooktop.......................................12
ConnectingtheGas.........................i...............12
GasandE_ecfricRequirementsTable..............13
InstallingtheBurnerComponents....................14
MakingtheElectricalConnection.....................15
Operation...........................................................16
VerifyingtheOperation....................................16

Preparing for Installation
ii!iiii!!ii!ii;
VERIFYPACKAGECONTENTS
••••••••••••••••••••••) TT
•Use & Care Manual
• Hold Down Bracket Kit
•Grate/Burner Cap Pack
•Burner Set
• Gas Pressure Regulator
• LP Conversion Kit
• Cleaning Kit
•Grill Drip Pan (E46GC67ESS only)
• Grill U-Burner (E46GC67ESS only)
• Grill Heat Control Channels (E46GC67ESS only)
• Grill (E46GC67ESS only)
• Grease Control Box (E46GC67ESS only)
iiii)J;)i!i
CABINET/COUNTERTOPPREPARATION
••••••••••••••••••••••
The installation of this built-in appliance must be completed by a qualified appliance
technician or contractor. Proper installation is the owner's responsibility.
Carefully check the location where the cooktop is to be installed. The cooktop
should be placed for convenient access, but away from drafts that may be caused
by open doors and windows or by HVAC duct outlets. Make certain that gas and
electrical power can be provided in the selected locations. Plan the installation so
that all minimum clearances are met or exceeded. Dimensions shown provide
minimum clearances, unless otherwise noted.
iJii]ii!iii!)_
iiii!Tii!i!i_iiAi
iiiiiiii!]_
iiii)il))i!))ii)iiiii
iiiii]!;!!i!illi¸
)

HUII_Ix
iiiii!ii!
!]i!;!ii_!
i!!ii!i!_i!]
i!i!i_!!!i}
Preparingfor Installation
Figure 1
18.
(457mm)
Mmximum
(762rnm) _
3 1/8"
Clearance= to CombumtlE4e=
Figu=re2
MimJmu m€lea _n_e
- I,_2:_bu,,,b,e
B I sun'aces
Under Cabinet Clearances
Plan the installation so that the electrical connection, gas
shut-off valve, and pressure regulator are accessible from the
front of the cabinet.
Model "A" Minimum "A" Maximum
E30GC64ESS 30"(762mm) 36"(914ram)
E36GC65ESS 36"(9t4mm) 42"(t067mm)
E46GC66ESS/67ESS 48"(1219ram) 54"(1372mm)
Model "B" Minimum
E30GC64ESS 29"(737mm)
E36GC65ESS 351/4"(895mm)
E46GC66ESS/67ESS 46"(1168mm)

Preparing for Installation
Figure 4
c_m D_=,_r_ for t_
FJ_ClISESS
Figure 3
(699m_)
Figure 5

i)iiii!iiii
i!!!iiiiiiii_
_i!!iii!ii_ii!ii
iiii_!!ii_))ii)
iiiiiiiiiiiiiili
ii!i!i!i!_!_iiil
MakingtheGas/ElectricConnection
REQUIREMENTS
••••••••••••••••••••••
GasSupplyRequirements
Check your local building codes for the proper method of installation. In the
absence of local codes, this appliance should be installed in accordance with the
National Fuel Gas Code ANSI Z223.1/NFPA 54. Be certain that the appliance being
installed is correct for the gas service being provided. Refer to the data plate
located on the bottom of the cooktop chassis.
iiiii_ii_iiiii

Making the Gas/Electric Connection
GasandElectricalSupplyRequirements
The correct voltage, frequency and amperage must be supplied to the appliance
from an isolated, grounded circuit which is protected by a properly sized circuit
breaker or time-delay fuse.
The cooktop must be connected to the power supply with copper wire only. The
use of aluminum wire may result in unsatisfactory connections. Flexible armored or
nonmetallic, sheathed copper cable (with a grounding wire) should be used to
supply electrical power to the junction box or receptacle.
The cooktop's factory-equipped, three-prong grounding plug must be inserted into a
mating grounding-type receptacle in accordance with National Electric Code and
applicable state, municipal and local codes.
Be certain to locate the junction box or electrical outlet so the electrical supply may
be easily disconnected in the event that service becomes necessary. Also, provide
extra slack in the cable to allow the cooktop to be removed for servicing.

i i!!iiiiii!
Installation
INSTALLINGTHECOOKTOP
!i;ii;i3i3!i• •••••••••••••••••••••
Figure 6 Place and center the cooktop within the cutout. Secure the
cooktop to the countertop utilizing the two (2) hold-down
brackets provided. Do not overtighten the screws. See
Figure 6.
_iiiii_i_iiiiii
CONNECTINGTHEGAS
••••••••••••••••••••••
T
A_ach the gas pressure regulator (included with the cooktop) to cooktop pipe nipple
inlet.
Install a gas shut-off valve (not included with the cooktop) in the main gas supply
line in an accessible location near the cool<top. Complete connection of the gas
supply to the cooktop by installing 1/2 inch flexible gas line (not included with the
cooktop) between the pressure regulator and the shut-off valve.

_i!i]iiiiiiiii!ili
Installation !iiiiii!_!!i!i
GASANDELECTRICREQUIREMENTSTABLE
Refer to the following table for more information on gas and electric requirements.
Model No.
E30GC64ESS
E36GC65ESS !
E46GC66ESS
E46GC67ESS
Above models
converted
to LP
Electrical
circuit
required
120VAC,
60Hz, 15A
Total
conne_ed
load
0.25 Amps
(O.O3Kw)
Gas type
Natural
Natural
Natural
Natural
Liquid Propane
Manifold
pressure
4" Water Column
4" Water Column
4" Water Column
4" Water Column
10" Water Column
Minimum gas
supply
pressure
5" Water Column
5" Water Column
5" Water Column
5" Water Column
11" Water Column
)ii)Jf_!iii!!_J
)fi_i))J!)ii_i_))

Installation
INSTALLINGTHEBURNERCOMPONENTS
••••••••••••••••••••••
BurnerComponents
Remove the brass burner rings, porcelain burner caps, and porcelain grates from
their shipping packages. Place each burner ring onto its corresponding burner
base, being certain that the five alignment tabs slide into the matching notches in
the base. Set each porcelain burner cap on top of its corresponding burner ring.
Place each grate onto the cooktop, being certain that the rubber feet are positioned
in the locating dimples.
Figure 7
Grate
./
Burner Components
. Burner Cap
/BurnerRing
//
..Top Frame
/
Burner Head (Fixed)
GrillComponents
Remove the grill components from inside the main
carton. Remove all of the packing materials from
the Grill, U-burner, Heat Control Channels, Grease
Control Box and the Drip Pans.
Begin your set up by placing the Drip Pans inside
on the bottom of the open grill burner box area,
using the dimples to locate the Drip Pan. Next, slip
the open end of the U-burner onto the gas stub
located in the front inside of the grill burner box, and
insert the bracket on to opposite end of the U-
burner into the slot located on the Grease Control
Box. Proceed to install the Heat Control Channels,
which sit on top of four pins at the inside front and
back of the grease control box. Finally, set the grill
in place on the top of the cooktop.

Installation
MAKINGTHEELECTRICALCONNECTION
mmnmmmnmmmnnmmmmmu
Plug the three-prong plug from the appliance into the properly grounded and
polarized wall receptacle.

O,e=, on
_ _'__ ___ VERIFYINGTHEOPERATION
NNNINININNNNNNNNNIINNNNNNN
Before beginning the test procedure, ensure that the gas supply is turned off at the
shut-off valve, all cooktop control valves are in the "OFF" position, and all burner
i rings, burner caps, and grates are properly positioned on the cooktop.
•" " II
Rotate one knob at a t me counterc ockw se to the Hi/LITE pos t on. Ver Iy that a
ignitors spark continuously, then return the knob to the "OFF" position. Repeat for
all knobs. See Figure 8.
_!_::_ Figure 8
ii_iiiiii!!i
;i!_iiiii_)
)ii!iii!il)
_iiiiii!ili

iJiii_iiilJ!!ii
Operation
iiiiiiii_i_iii
Turn on the main gas supply to the cooktop by opening the gas shut-off valve. Test
each burner separately by pressing and turning one control knob at a time
counterclockwise to the "HI/LITE" position. All ignitors will spark simultaneously. (It
will take approximately four seconds for ignition to occur, at which time all igniters
will stop sparking. If ignition does not occur within four seconds, turn off the knob,
wait for at least two minutes to allow any gas to dissipate, then repeat this ignition
test.) The control knob can then be rotated counterclockwise from "HI" to "LOW" to
adjust the flame height progressively. Repeat the ignition test for all burners.
When installed properly, the flame will be steady and quiet. It will also have a sharp,
blue inner cone that will vary in length proportional to the burner size. Flame
adjustment will not be necessary.
Read and understand the accompanying Use &Care Manual prior to cooking with
this appliance. The Use &Care Manual contains additional important safety,
service and warranty information.

L_Electrolux