Electrolux EI36EC45KB1 User manual

Canada INSTALLATION AND SERVICE MUST BE PERFORMED
BY A QUALIFIED INSTALLER.
IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
V__FOR YOUR SAFETY: Do not store or use gasoline or other
flammable vapors and liquids in the vicinity of this or any other appliance.
United States
Cooktop Dimensions IMPORTANT INSTALLATION INFORMATION
• All electric cooktops run off a single phase, three-wire or
four-wire cable, 240/208 volt, 60 hertz, AC only electrical
supply with ground.
• Minimum distance between cooktop and overhead cabinetry
is 30" (76.2 cm).
30" Min. *
A
Cooktop Cutout
Dimensions
H
i ii
* 30" (76.2 cm) min. for unprotected cabinet
24" (61 cm) min. for protected surface
C4" X 8" (10.2 cm x 20.3 cm)
opening to route armored cable
if a panel is present
Front Rear
G
Figure 1
3 1/8
(7,9)
3½
7½
6 5/8
Side view
PRODUCTDIMENSIONS
MODEL I A:wiDTH ! BIDEPTH I C HEIGHTD_EIGHT E:BoXwiDTH " F.BOXDEPTH
30"CeramicModel 303A(78.1) 213A(55.2) 31/8(7.9) 65/8(16.8) 285/8(72,7) 19¼(48.9)
36"CeramicModel 363A(93.3) 213A(55,2) 31/8(7,9) 65/8(16.8) 345/8(87,9) 19¼(48,9)
30"CeramicModel 293A(75.6)
36"CeramicModel 353A(90.8)
All dimensions are in inches (cm).
Printed in Canada
30(76,2) 203/8(51,8) 205/8(52,4) 8Y2(21.6)
36(91,4) 203/8(51,8) 205/8(52,4) 8Y2(21.6)
P/N 318205426 (1202) Rev. B
English - pages 1-6
Espahol- pages 7-12
Fran_ais - pages 13-18
Notes - pages 19-20

Overhead Cabinet Should Not Exceeda
Maximum Depth of 13" (33 cm)
Clearance Between the [ K Min• Recommended i |
Top of the Cooking Distance Between Rear
Platform and the Bottom
of an Unprotected Wood
or Metal Cabinet• _
24" (61 cm) Min. when
Bottom of Wood or Metal
Cabinet is Protected by
Not LessThan 1/8" (0.3
cm) Flame Retardant
Millboard Covered With
Not LessThan No. 28
MGS Sheet Steel, 0.015"
(0.4 mm) Stainless
Steel, 0.024" (0.6 mm)
Aluminum or 0.020" (0.5
mm) Copper•
e of Cutout and
"_ Nearest Combustible
Surface Above
Countertop
18" G
(45.7 cm)
1 0"
( 25.4 cm)
J Min. From Edge of
Cooktop to Nearest
Combustible Wall
(Either Side of Unit)•
2 1/2" (6.4 cm) Min. From EJge
of Cutout to Front Edgeof
Countertop
Install junction box at a
location which will be easy
to reach and that will not
interfere with the cooktop
installation• We suggest
12" (30.48cm) lower than
the countertop.
Letters on this figure refer to chart on front page except for J, I( & L.
If a drawer is present
underneath, allow at least
10" (25.4cm) of clearance
below the countertop.
Never store
flammable products in the
drawer•
Toeliminate the risk of burns or
fire byreaching over heatedsurfaces,cabinet
storage spacelocated abovethe cooktop should
be avoided• If cabinet storage is provided, risk
can be reducedby installing a range hood that
projects horizontally a minimum of 5" (12•7 cm)
beyond the bottom of the cabinets• 30" (76.2 cm) 2" (5.1 cm) 2" (5.1 cm) 30" (72.6 cm)
36"(914 cm) 2" (5.1 cm) 2" (5.1 cm) 36" (91.4 cm)
Figure 2 - COUNTERTOP CUTOUT OPENING
2

For typical under counter installation of an electric built-in oven with an electric cooktop over.
Only certain cooktop models may be installed over
certain built-in electric oven models. Approved
cooktops and built-in ovens are listed by the MFG
ID number and product code (see the insert sheet
included in the literature package and cooktop
installation instructions for dimensions).
To reduce the risk of
personal injury and
tipping of the wall
oven, the wall oven
must be secured to
the cabinet (s) by
mounting brackets.
208/240 Volt junction box
for built-in oven.
Approx. 3"
(7.5 cm)
Cut an opening in wood base minimum
4" x 4" (10.2 X 10.2 cm), 2" (5 cm) from
left side filler panel, to route armourecl
cable to junction box.
Note 1: 4" x 4" (10.2 X 10.2 cm) opening to route
armourecl cable from cooktop to junction box.
208/240Volt
Approx. 3'_
(7.5 cm) junction box
for Cooktop
Cabinet side filler
panels are necessary to
isolate the unit from
adjoining cabinets.
Cabinet side filler
height should allow for
installation of approved
models
36" Min.
(91.4 cm) Min.
Unit will
overlap
cutout
(minimum)
edges by
1" (2.5cm)
Use 3/4" (1.9 cm) plywood,
installed on two runners, flush
with toe plate. Basemust be
capable of supporting 150
pounds (68 kg) for 27" models
and 200 pounds (90 kg) for
30" models.
41/2"(1 1.5 cm)
Max.*
*If no cooktop is installed directly over the oven unit, 5" (12.7 cm) maximum is allowed above the floor.
27"(68.6cm) 24 7/8"(63.2cm)Min. 27¼"(69.2cm)Min.
23W'(59.7cm)
WallOven 25¼"(64.1cm)Max. 28¼"(71.8cm)Max.
30"(76.2cm) 28W'(72.4cm)Min. 27¼"(69.2cm)Min.
23W'(59.7cm)
WallOven 29"(73.7cm)Max. 28¼"(71.8cm)Max.
TYPICAL UNDER COUNTER INSTALLATION OF A SINGLE ELECTRICBUILT-IN OVEN
WITH AN ELECTRICCOOKTOP MOUNTED ABOVE
3

Important Notes to the Installer
1. Read all instructions contained in these installation
instructions before installing the cooktop.
2. Remove all packing material before connecting the
electrical supply to the cooktop.
3. Observe all governing codes and ordinances.
4. Be sure to leave these instructions with the consumer.
Important Note to the Consumer
Keep these instructions with your Use and Care Guide for
future reference.
IMPORTANT SAFETY
INSTRUCTION
• Be sure your cooktop is installed and grounded
properly by a qualified installer or service
technician.
These cooktops must be electrically grounded in
accordance with local codes or, in their absence,
with the National Electrical Code ANSI/NFPA No.
70--latest edition in the United States, or with
CSA Standard C22.1, Canadian Electrical Code,
Part 1, in Canada.
The electrical power to the cooktop
must be shut off while line connections are being
made. Failure to do so could result in serious injury
or death.
Provide Electrical Connection
Install the junction box under the cabinet and run
120/240 or 120/208 Volt, AC wire from the main
circuit panel. NOTE: DO NOT connect the wire to the
circuit panel at this time. Wait until all wires have been
connected in the junction box.
Electrical Requirements
Observe all governing codes and local ordinances.
1. A 3-wire or 4-wire single phase 120/240 or 120/208
Volt, 60 Hz AC only electrical supply is required on a
separate circuit fused on both sides of the line (time-
delay fuse or circuit breaker is recommended, 40A or
50A). DO NOT fuse neutral.
An extension cord must not be used
with this appliance. Such use may result in a fire,
electrical shock, or other personal injury.
2. The appliance should be connected to the fused
disconnect (or circuit breaker) box through flexible
armored or nonmetallic sheathed cable. The flexible
armored cable extending from this appliance should
be connected directly to the grounded junction box.
The junction box should be located as shown in
Figure 3 with as much slack as possible remaining in
the cable between the box and the appliance, so it
can be moved if servicing is ever necessary.
3. A suitable strain relief must be provided to attach
the flexible armored cable to the junction box.
Unpacking Instructions
1. Unpack and visually inspect the cooktop
2. Be sure the bottle of cleaner conditioner packed
in the literature bag is left where the user can
find it easily. It is important that the ceramic-glass
smoothtop be pretreated before use see Cooktop
Cleaning and Maintenance section in the Use and
Care Guide.
Model and Serial Number Location
The serial plate is located under the cooktop.
When ordering parts for or making inquires about your
cooktop, always be sure to include the model and serial
numbers and a lot number or letter from the serial plate
on your cooktop.
Model and Serial Plate
(Under Cooktop)
Figure 3
/
/
NOTE: Wire sizes and connections must conform with
the fuse size and rating of the appliance in accordance
with the National Electrical Code ANSI/NFPA No. 70-
latest edition, or with CSA standard C22.1, Canadian
Electrical Code, Part 1, and local local codes and
ordinances.
4

Electrical connection
It is the responsibility and obligation of the consumer to
contact a qualified installer to assure that the electrical
installation is adequate and is in conformance with the
National Electrical Code ANSI/NFPA No. 70-latest edition,
or with CSA Standard C22.1, Canadian Electrical Code,
Part 1, and local codes and ordinances.
Where local codes permit connecting the appliance-
grounding conductor to the neutral (white) wire
(US Only) (see figure 4):
1. Disconnect the power supply.
2. In the junction box:
Connect appliance and power supply cable wires as
shown in Figure 4.
Risk of electrical shock (Failure to
heed this warning may result in electrocution or
other serious injury,) This appliance is equipped
with copper lead wire, If connection is made to
aluminum house wiring, use only connectors that
are approved for joining copper and aluminum wire
in accordance with the National Electrical Code
and local code and ordinances. When installing
connectors having screws which bear directly on
the steel and/or aluminum flexible conduit, do no
tighten screws sufficiently to damage the flexible
conduit. Do not over bend or excessively distort
flexible conduit to avoid separation of convolutions
en exposure of internal wires.
DO NOT ground to a gas supply pipe. DO NOT connect
to electrical power supply until appliance is permanently
grounded. Connect the ground wire before turning on
the power.
(If your appliance is equipped with a
white neutral conductor,)
This appliance is manufactured with a white neutral
power supply and a frame connected copper wire,
The frame is grounded by connection of grounding
lead to neutral lead at the termination of the
conduit, if used in USA, in a new branch circuit
installation (1996 NEC), mobile home, recreational
vehicles, where local code do not permit grounding
trough the neutral (white) wire or in Canada,
disconnect the white and green lead from each
other and use ground lead to ground unit in
accordance with local codes, connect neutral lead
to branch circuit-neutral conductor in usual manner
see Figure 5. If your appliance is to be connected
to a 3 wire grounded junction box (US only),
where local code permit connecting the appliance-
grounding conductor to the neutral (white) see
Figure 4.
NOTE TO ELECTRICIAN: The armored cable leads
supplied with the appliance are UL-recognized for
connection to larger gauge household wiring. The
insulation of the leads is rated at temperatures much
higher than temperature rating of household wiring. The
current carrying capacity of the conductor is governed by
the temperature rating of the insulation around the wire,
rather than the wire gauge alone.
Cable from Power Supply
White Wire
(Neutral)_
Red ---_,_["
Wires
Ground Wire
(Bare or Green Wire)
Wires-
_W uncti°n
Box
White Wire
(Neutral)
U.L.-Listed Conduit
Connector (or CSA listed)
Cable from appliance
Figure 4
3-WIRE GROUNDED JUNCTION BOX
If the appliance is used in a new branch circuit
installation (1996 NEC), mobile home, recreational
vehicle, or where local codes DO NOT permit
grounding through the neutral (white) wire, the
appliance frame MUST NOT be connected to the
neutral wire of the 4-wire electrical system. (see
figure 5):
1. Disconnect the power supply.
2. Separate the green (or bare copper) and white
appliance cable wires.
3. In the junction box:
Connect appliance and power supply cable wires as
shown in Figure 5.
Cable from Power Supply
Ground Wire
Red White Wire
GBrw_!!_odrWI ire__
Junction __" ---_U.L.-Listed Conduit
Cable from Connector (or CSA
appliance listed)
Figure 5
4-WIRE GROUNDED JUNCTION BOX

Cooktop Installation
1. Visually inspect the cooktop for damage. Also make
sure all cooktop screws are tight (see Figure 6).
3. Set the cooktop into the countertop cutout.
NOTE: Do not use caulking compound; cooktop should
be removable for service when needed.
Screws
Figure 6
2. Install the retainer brackets. See Figure 7
The retainer brackets MUST be installed, to meet
local codes or, in their absence, with the National
Electrical Code ANSI/NFPA No. 70--latest edition
in the United States, or with CSA Standard C22.1,
Canadian Electrical Code, Part 1 in Canada (see
Figure 7).
Cooktop Countertop
spacer
Retainer bracket
Figure 7
Do not remove the nylon spacers on
the edges of the cooktop. These spacers center the
cooktop in the space provided. The cooktop must
be centered to prevent excess heat buildup that
may result in heat damage or fire (see Figure 8).
6 Nylon spacers
Position brackets .-j_
on unit cutout .: _-_" :
center line ..::::::
2 Retainer_
brackets ..........
Figure 8
Granite countertop Installation Kit
A Granite Countertop Installation kit # 903061-9010 can
be ordered through a Service Center or by phone at 1-877-
ELECTROLUX (1-877-435-3287).
Checking Operation
Refer to the Use and Care Guide for operation.
Do not touch cooktop glass or elements.
They may be hot enough to burn you.
Model and Serial Number Location
The serial plate is located under the cooktop.
When ordering parts for or making inquires about your
cooktop, always be sure to include the model and serial
numbers and a lot number or letter from the serial plate
on your cooktop.
Before you Call for Service
Read the Before You Call for Service Checklist and
operating instructions in your Use and Care Guide.
It may save you time and expense. This includes
common occurences that are not the result of defective
workmanship or materials in this appliance.
Refer to your Use and Care Guide for sevice phone num-
bers,
6

Canad_ LA INSTALACION Y EL SERVICIO DEBEN SER EFECTUADOS POR
UN INSTALADOR CALIFICADO.
IMPORTANTE: GUARDE ESTAS INSTRUCCIONES PARA USO DEL
INSPECTOR LOCAL DE ELECTRICIDAD.
LEA Y GUARDE ESTAS INSTRUCCIONES PARA REFERENCIA FUTURA.
PARA SU SEGURIDAD: No amanece ni utilice gasolina u otros
vapores y liquidos inflamables en la proximidad de este o de cualquier otto
artefacto.
Estados Unidos
Dimensionesde la Estufa
i
INFORMACION IMPORTANTE PARA LA INSTALACION
, Todas las estufas electricas funcionan con una alimentaci6n electrica con
puesta a tierra de fase singular, 3 o 4 alambres, 240/208 voltios, 60 hertz
y s61oAC.
Favor de notar que la distancia minima entre la superficie de la estufa y
los gabinetes adyacentes y por encima son de 30" (76.2 cm).
30" Min. *
(76.2 A
Dimensiones del
Recortado de la Estufa
H
* 30" (76.2 cm) m[n. para un gabinete desprotegido.
24" (61 cm) m[n. para una superficie protegida.
4" X 8" (10.2 cm X
20.3 cm) apertura
para el cable si
existe un pan&
G
Figura 1
Parte delantera
3 1/8
(7,9)
(19,1)
Vista de lado
Parte trasera
6 5/8
DIMENSIONESDELAESTUFA
MODELO I A:ANCHuRA PROFuNDiDADc ALTURAD:ALTURAE.ANCHODELACA]A EPROFuNDIDADDELA
I ] ] I CAJA
t
MODELO30' 303A(781) 213A(552) 31/8(79) 65/8(168) 285/8(72,7) 19¼(489)
MODELO36" 363A(933) 213A(552) 31/8(79) 65/8(16,8) 345/8(87,9) 19¼(489)
MODEL030' 293A(75.6)
MODELO36" 353A(90,8)
Todas las dimensiones sedan en pulgadas (cm).
Impreso en Canada
30(76,2) 203/8(51,8)
36(91,4) 203/8(51,8)
7
205/8(52,4) 8Y2(21.6)
205/8(52,4) 8Y2(21.6)
P/N 318205426 (1202) Rev. B
English - pages 1-6
Espahol- pages 7-12
Fran_ais - pages 13-18
Notas - pages 19-20

Elarmario superior no debe sobrepasar una
profundidad maxima de 13" (33 cm)
30" (76.2 cm) min. de espacio I 'recomendada e_re el k,,, I I
entre la parte superior del fogOn y \"\ i horde trasero del corte _i __------J
la parte inferior de un armario de "-4__-y el compartimiento de --
madera o metal sin protecciOn.
24" (61 cm) min. cuando la
parte inferior del armario de
madera o metal est,1protegida
por una placa cortafuego
retardante de llama de no
menos de 1/8" (0.3 cm),
cubierta con una lamina de
acero msg no inferior al No.
28, de acero inoxidable de
0.015"(0.4 mm), aluminio de
0.024" (0.6 mm) o cobre de
0.020" (0.5 mm).
"-.combustible m_iscercano
sobre la parte superior del
armario
18" G
(45.7 cm)
10" cm)
J min. desde el borde
corte hasta el
compartimiento de
combustible (ambos
lados del artefacto)
2 1/2" (6.4 cm) mfn. desde el borde delantero
del corte hasta el borde delantero de la parte
superior del armario
Instalar la caja de conexiones en un
lugar que ser_if_icil de alcanzar y
que no interfiera con la instalaciOn
de la cubierta superior. Sugerimos
12" (30.48 cm) por debajo de la
superficie del mueble.
Para las dimensiones 6, H y I, v6ase la tabla en la pagina 1.
Si hay un caj6n debajo, dejar
al menos 10" (25.4 cm) de
espacio libre con respecto a la
superficie del mueble.
Nunca almacene
productos inflamables en el
cajOn.
Para evitar riesgos de
quemaduras o incendios al tocar superficies
calientes, se deben evitar los armarios sobre
la superficie de los quemadores. Si existe
un armario, se pueden reducir los riesgos
instalando una campana que se extienda
horizontalmente en un minimo de 5"
(12.7 cm) por sobre la parte inferior de los
armarios.
30" (76.2 cm)
36"(91.4cm)
2" (5.1 cm)
2" (5.1 cm)
¸
2" (5.1 cm)
2" (5.1 cm)
30" (72.6 cm)
36" (91.4 cm)
Figura 2- EL CORTE DE LA PARTE SUPERIOR DEL ARMARIO
8

Instalad6n tipica para una estufa electrica endma de un homo de pared instalado debaio
del mostrador
S01ociertos modelos de tapas de cocina se pueden
instalar sobre ciertos modelos de hornos el_ctri-
cos empotrados. Lastapas de cocina y los hornos
empotrados se mencionan pot su n0mero de
identificaci6n MFG ID y c6digo de producto (vet la
planilla que se incluye en el paquete de literatura y
las instrucciones de instalaci6n de la cocina donde
est_qndetalladas las dimensiones).
Para redudr el riesgo de
lesiones personales y
inclinaci6n del homo de
pared, este debe ase-
gurarse a los gabinetes
mediante soportes de
montaje.
Approx. 3"
(7.5 cm)
208/240V caja de empalme
para hornos de
Corte una abertura de 4" X 4"(10.2 cm X 10.2 cm),
a 2" (5 cm) del lado izquierdo del panel Ilenador, para
poder encaminar el cable a la caja de empalme.
Nota 1: Apertura de 4" x 4" (10.2 x 10.2 cm) para guiar
el cable blindado de la cubierta a la caja de conexiones.
208/240V caja
de empalme
Approx. 3 )ara la estufa
(7.5 cm) electrica
Lospaneles de relleno
laterales del gabinete son
necesarios para aislar la
unidad de los gabinetes
adyacentes. La altura del
relleno lateral del gabinete
debe permitir la instalaci6n
de modelos de tapas de
cocina aprobados.
36" Min.
(91.4 cm) Min.
Corte
(minimo)
hasta que
sobre pase
la orilla pot
1 pulgada
(2.5cm)
Instale contrachapado de 3A" (1.9
cm) sobre dos correderas, nivela-
do con la parrilla inferior. La base
debe poder sostener 150 libras (68
kg) para los modelos 27"y 200 li-
bras (90 kg) para los modelos 30"
4 1/2"
(11.5 cm) Max.*
* Si no se instala ninguna tapa de cocina directamente sobre la unidad del homo, se per-
mite un espacio m_qximode 5" (12,7 cm) sobre el piso.
27"(68.6cm) 247/8"(63.2cm)Min.
Homodepared 25¼"(64.1cm)M_ix.
30"(762cm) 28½"(72.4cm)Min.
Homodepared 29"(73.7cm)M_ix.
INSTALACION TIPICA DEBAJO DE LA ME',
23½"(59.7cm)
23½"(59.7cm)
27¼"(69.2cm)Min.
28¼"(71.8cm)M_ix.
27¼"(69.2cm)Min.
28¼"(71.8cm)M_ix.
ADA DE HORNO SIMPLE EMPOTRADO
CON TAPA DE COCINA MONTADA
9

Notas importantes para el instalador
1. Lea todas lasinstrucciones contenidas en este manual
antes de instalar la estufa.
2. Saque todo el material usado en el embalaje de la
estufa antes de conectar el suministro el_ctrico a la
estufa.
3. Observe todos los c6digos y reglamentos pertinentes.
4. Deje estas instrucciones con el consumidor.
Nota importante ai consumidor
Conserve estas instrucciones y el Manual del usuario para
referencia futura.
INSTRUCCIONES
IMPORTANTES DE SEGURIDAD
• Asegurese de que su estufa sea instalada y puesta
a tierra de forrna apropiada pot un instalador
calificado o pot un t6cnico de servido.
• Esta estufa debe ser el6ctricamente puesta a tierra
de acuerdo con los c6digos locales o, en su ausencia,
con el C6digo EI6ctrico National ANSI/NFPA No. 70
- ultirna edid6n en los Estados Unidos, o el C6digo
EI6ctrico Canadiense CSA Standard C22.1, Part 1 en
Canada. La alimentad6n el6ctrica a la estufa
deberia apagarse mientras se hacen las conexiones de
linea. El no harcelo podria resultar en dafios serios o la
muerte.
Provea conexi6n el6ctrica
Instale la caja de empalmes debajo del armario y provea
un cable de 120/240 o 120/208 Voltios, AC al panel de
circuitos del aparato. NO conecte la cable al panel de
circuitos en este momento. Espere hasta que todos los
alambres est_n conectados en la caja de empalmes.
Requisitos el6ctricos
Cumpla con todos los cOdigos en vigor y todos los
reglamentos locales.
1. Para el suministro el_ctrico solamente se necesita
corriente con frecuencia de 60 Hz AC y fase 0nica de
120/240 o 120/208 voltios suministrada por cable de
3 o de 4 alambres en un circuito separado con fusibles
en ambos lados de la linea (serecomienda un fusible
de tiempo retardado o un cortacircuitos, 40A 0 50A).
NO ponga un fusible en el hilo neutro.
NOTA: Eltamaho de los cables y de lasconexiones debe
de estar en conformidad con el tamaho del fusible y con la
capacidad del electrodom_stico y de acuerdo con el C6di-
go El_ctrico Nacional ANSI/NFPANo. 70 - 01tima edici6n y
los c6digos y reglamentos locales.
No se debe usar una alargadora para
enchufar este electrodom6stico. Esto podria resultar
en un incendio, un choque el6ctrico u otro tipo de
da5o personal.
2. Este electrodom_stico debe conectarse a la caja de
fusibles (o de cortacircuitos), por medio de un cable
blindado flexible o un cable con forro no met_ilico. El
cable blindado flexible que va desde el electrodom_s-
tico debe de estar conectado directamente a la caja de
empalme. La caja de empalme debe de estar Iocali-
zada en el lugar que seindica en la Figura 3, dejando
tanto exceso de cable como seaposible entre la caja
y el electrodom_stico, de forma que asi el electrodo-
m_stico se pueda mover f_icilmente, si fuera necesario
para hacer una reparaciOn.
3. Se debe de usar un conectador que reduzca la tirantez
de una forma adecuada para unir el cable blindado
flexible a la caja de empalme.
Instrucdones de desembalaje
1. Inspeccione visualmente la tapa de la cocina para ver
si est,1dahada.
2. Aseg0rese que la botella de limpiador ubicada en
la empaquete de literatura esta situada en un lugar
donde puede encontrarse f_icilmente. Esimportante
de tratar de antemano la superficie en vidrio de
cer_imico antes de utilizar. Ve la parte sobre Limpieza
y Mantenimiento de la Cubierta en este Manual
del usuario.
Ubicad6n del nurnero de rnodelo y de serie
La placa con el n0mero de modelo y de serie est,1
ubicada en el fondo de la estufa
Cuando haga pedidos de repuestos o solicite informaci6n
con respecto a su estufa, est@siempre seguro de incluir
el n0mero de modelo y de serie y el n0mero o letra del
Iote de la placa de serie de su homo.
/
/
/
Placa con los numeros de modelo y serie
(debajo de la cubierta)
Figura 3
10