Element 455w User manual

455W POS Terminal

User Manual

Element 455W User Manua I Page 2of 32

Version 1.0

The information contained in this document is subject to change without notice.

We make no warranty of any kind with regard to this material, including, but not limited to, the implied

warranties of merchantability and fitness for a particular purpose. We shall not be liable for errors

contained herein or for incidental or consequential damages in connection with the furnishing, performance,

or use of this material.

This document contains proprietary information that is protected by copyright. All rights are reserved. No part

of this document may be photocopied, reproduced or translated to another language without the prior

written consent of the manufacturer.

TRADEMARK

Intel®, Pentium® and MMX are registered trademarks of Intel® Corporation. Microsoft® and Windows®

are registered trademarks of Microsoft Corporation.

Other trademarks mentioned herein are the property of their respective owners.

Safety

IMPORTANT SAFETY INSTRUCTIONS

1. To disconnect the machine from the electrical power supply, turn off the power switch and remove the power

cord plug from the wall socket. The wall socket must be easily accessible and in close proximity to the

machine.

2. Read these instructions carefully. Save these instructions for future reference.

3. Follow all warnings and instructions marked on the product.

4. Do not use this product near water.

5. Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious damage

to the product.

6. Slots and openings in the cabinet and the back or bottom are provided for ventilation to ensure reliable

operation of the product and to protect it from overheating. These openings must not be blocked or covered.

The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface.

This product should never be placed near or over a radiator or heat register or in a built-in installation unless

proper ventilation is provided.

7. This product should be operated from the type of power indicated on the marking label. If you are not sure of

the type of power available, consult your dealer or local power company.

8. Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the

cord.

9. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage

points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the

product.

Element 455W User Manua I Page 3of 32

CE MARK

This device complies with the requirements of the EEC directive 2014/30/EU with regard to

“Electromagnetic compatibility” and 2014/35/EU “Low Voltage Directive”.

FCC

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that may cause undesired

operation.

CAUTION ON LITHIUM BATTERIES

There is a danger of explosion if the battery is replaced incorrectly. Replace only with the same or

equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer’s

instructions.

Battery Caution

Risk of explosion if battery is replaced by an incorrectly type. Dispose of used battery

according to the local disposal instructions.

Safety Caution

Note: To comply with IEC60950-1 Clause 2.5 (limited power sources, L.P.S) related

legislation, peripherals shall be 4.7.3.2 “Materials for fire enclosure” compliant.

4.7.3.2 Materials for fire enclosures

For MOVABLE EQUIPMENT having a total mass not exceeding 18kg.the material of a FIRE ENCLOSURE, in the

thinnest significant wall thickness used, shall be of V-1 CLASS MATERIAL or shall pass the test of Clause A.2.

For MOVABLE EQUIPMENT having a total mass exceeding 18kg and for all STATIONARY EQUIPMENT, the

material of a FIRE ENCLOSURE, in the thinnest significant wall thickness used, shall be of 5VB CLASS MATERIAL

or shall pass the test of Clause A.1

Element 455W User Manua I Page 4of 32

LEGISLATION AND WEEE SYMBOL

2012/19/EU Waste Electrical and Electronic Equipment Directive on the treatment, collection, recycling

and disposal of electric and electronic devices and their components.

The crossed dust bin symbol on the device means that it should not be disposed of with other household

wastes at the end of its working life. Instead, the device should be taken to the waste collection centers for

activation of the treatment, collection, recycling and disposal procedure.

To prevent possible harm to the environment or human health from uncontrolled waste disposal, please

separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of

material resources.

Household users should contact either the retailer where they purchased this product, or their local

government office, for details of where and how they can take this item for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of the purchase contract.

This product should not be mixed with other commercial wastes for disposal.

Element 455W User Manua I Page 5of 32

RevisionHistory

Changes to the original user manual are listed below:

 
 
Element 455W User Manua I Page 6of 32 
 
 TABLE OF CONTENTS 
1. Packing List.......................................................................................................................................7 
1-1. Standard Accessories .......................................................................................................7 
1-2. Optional Accessories........................................................................................................8 
2. System View.....................................................................................................................................9 
2-1. Front & Side View.............................................................................................................9 
2-2. Rear View .........................................................................................................................9 
2-3. IO Ports View..................................................................................................................10 
2-4. System Dimensions........................................................................................................11 
3. System Assembly & Disassembly ...................................................................................................12 
3-1. Disassemble the Stand ...................................................................................................12 
3-2. Remove the Cable Cover ................................................................................................12 
3-3. Install the Power Adapter ..............................................................................................13 
3-4. Replace the M.2 SSD Card ..............................................................................................13 
4. Peripheral Installation....................................................................................................................14 
4-1. Install the MSR / Fingerprint / iButton Module..............................................................14 
4-2. Install the Customer Display ..........................................................................................15 
4-3. Install the Second Display ..............................................................................................16 
4-4. Cash Drawer Installation ................................................................................................17 
5. Specification ..................................................................................................................................19 
6. Configuration.................................................................................................................................21 
6.1 F34 Motherboard.............................................................................................................21 
6.2 F64U Motherboard..........................................................................................................27 
 