Element CA850 User manual

Element CA850 User Manual Page 1 of 51
VERSION 2.0 December 2022

Element CA850 User Manual Page 2 of 51
Copyright 2022
All Rights Reserved
Manual Version 2.0
The information contained in this document is subject to change without notice.
We make no warranty of any kind with regard to this material, including, but not limited to, the implied
warranties of merchantability and fitness for a particular purpose. We shall not be liable for errors
contained herein or for incidental or consequential damages in connection with the furnishing,
performance, or use of this material.
This document contains proprietary information that is protected by copyright. All rights are
reserved. No part of this document may be photocopied, reproduced or translated to another
language without the prior written consent of the manufacturer.
Intel®, Pentium® and MMX are registered trademarks of Intel® Corporation. Microsoft® and
Windows® are registered trademarks of Microsoft Corporation.
Other trademarks mentioned herein are the property of their respective owners.
1. To disconnect the machine from the electrical power supply, turn off the power
switchand remove the power cord plug from the wall socket. The wall socket must
be easily accessible and in close proximity to the machine.
2. Read these instructions carefully. Save these instructions for future reference.
3. Follow all warnings and instructions marked on the product.
4. Do not use this product near water.
5. Do not place this product on an unstable cart, stand, or table. The product may
fall, causing serious damage to the product.
6. Slots and openings in the cabinet and the back or bottom are provided for
ventilation to ensure reliable operation of the product and to protect it from
overheating. These openings must not be blocked or covered. The openings
should never be blocked by placing the product on a bed, sofa, rug, or other similar
surface. This product should never be placed near or over a radiator or heat
register or in a built-in installation unless proper ventilation is provided.
7. This product should be operated from the type of power indicated on the marking
label.If you are not sure of the type of power available, consult your dealer or local
power company.
8. Do not allow anything to rest on the power cord. Do not locate this product where
persons will walk on the cord.
9. Never push objects of any kind into this product through cabinet slots as they may
touch dangerous voltage points or short out parts that could result in a fire or
electric shock. Never spill liquid of any kind on the product.

Element CA850 User Manual Page 3 of 51
This device complies with the requirements of the EEC directive 2014/30/EU with
regard to “Electromagnetic compatibility” and 2014/35/EU “Low Voltage Directive”.
This device complies with part 15 of the FCC rules. Operation is subject to the
followingtwo conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that
maycause undesired operation.
There is a danger of explosion if the battery is replaced incorrectly. Replace
onlywith the same or equivalent type recommended by the manufacturer. Discard
used batteries according to the manufacturer’s instructions.
Risk of explosion if battery is replaced by an incorrectly type. Dispose of used battery
according to the local disposal instructions.
Note: To comply with IEC60950-1 Clause 2.5 (limited power sources, L.P.S) related
legislation, peripherals shall be 4.7.3.2 “Materials for fire enclosure” compliant.
4.7.3.2 Materials for fire enclosures
For MOVABLE EQUIPMENT having a total mass not exceeding 18kg.the material
of a FIRE ENCLOSURE, in the thinnest significant wall thickness used, shall be of V-
1 CLASSMATERIAL or shall pass the test of Clause A.2.
For MOVABLE EQUIPMENT having a total mass exceeding 18kg and for all
STATIONARYEQUIPMENT, the material of a FIRE ENCLOSURE, in the thinnest
significant wallthickness used, shall be of 5VB CLASS MATERIAL or shall pass the
test of Clause A.1

Element CA850 User Manual Page 4 of 51
2012/19/EU Waste Electrical and Electronic Equipment Directive on the treatment,
collection, recycling and disposal of electric and electronic devices and their
components.
The crossed dust bin symbol on the device means that it should not be disposed
of with other household wastes at the end of its working life. Instead, the device
should be taken to the waste collection centers for activation of the treatment,
collection, recycling and disposal procedure.
To prevent possible harm to the environment or human health from uncontrolled
wastedisposal, please separate this from other types of wastes and recycle it
responsibly topromote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this
product,or their local government office, for details of where and how they can take
this item forenvironmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of
the purchase contract.
This product should not be mixed with other commercial wastes for disposal.

Element CA850 User Manual Page 5 of 51
Changes to the original user manual are listed below:
Revision
Description
Date
1.0
•Initial release
November
2020
2.0
•F64U motherboard removed
•F34 & F84U motherboard added
•D84U & F14 motherboard version update
December
2022

Element CA850 User Manual Page 6 of 51
1. Packing List.............................. 9
1-1. Standard Accessories .......................................................9
1-2. Optional Accessories ..................................................... 10
2. System View........................... 11
2-1. Front & Side View ........................................................... 11
2-2. Rear View......................................................................... 11
2-3. IO Ports View................................................................... 12
2-4. System Dimensions ....................................................... 13
3. System Assembly & Disassembly14
3-1. Install the Power Adapter.............................................. 14
3-2. Remove the System Box ............................................... 14
4. Peripherals Installation............ 16
4-1. Install the MSR/ NFC/ iButton/ Fingerprint Module.. 16
4-2. Install the Customer Display......................................... 17
4-3. Install the Second Display.............................................. 18
4-4. Install the Table Mount Kits........................................... 20
4-5. Cash Drawer Installation................................................ 21

Element CA850 User Manual Page 7 of 51
5. Specification ..................................... 23
6. Configuration..........................31
6-1. D84U Motherboard ......................................................... 31
6-1-1. Motherboard Layout......................................................... 31
6-1-2. Connectors & Functions .................................................. 32
6-1-3. Jumper Settings ................................................................ 33
6-2. F14 Motherboard ............................................................ 37
6-2-1. Motherboard Layout......................................................... 37
6-2-2. Connectors & Functions .................................................. 38
6-2-3. Jumper Settings ................................................................ 39
6-3. F34 Motherboard ............................................................ 42
6-3-1. Motherboard Layout......................................................... 42
6-3-2. Connectors & Functions .................................................. 43
6-3-3. Jumper Settings ................................................................ 44
6-4. F84U Motherboard.......................................................... 48
6-4-1. Motherboard Layout......................................................... 48
6-4-2. Connectors & Functions ..................................................49
6-4-3. Jumper Settings ................................................................ 50

Element CA850 User Manual Page 8 of 51
The page is intentionally left blank.

Element CA850 User Manual Page 9 of 51
1-1. Standard Accessories
a. System
b. Power adapter (90W)
c. Power cord
Note: Power cord will be supplied differently according to various region or country.

Element CA850 User Manual Page 10 of 51
1-2. Optional Accessories
a
b
c
d
e
f
g
h
a. MSR module
b. NFC module
c. iButton module
d. Fingerprint
e. Customer display
f. 11.6" or 15.6" 2nd display
g. Motherboard box
h. Powered USB box

Element CA850 User Manual Page 11 of 51
2-1. Front & Side View
1
2 3
No.
Description
1
Touch screen
2
USB2.0
3
Power button
4
Hinge cover
5
Stand arm
6
Stand arm cover
7
Stand front cover
2-2. Rear View
1 1
2
3
No.
Description
1
Dummy door of MSR/iButton module
2
Power/OSD button
3
System box
4
5
7
6
7

Element CA850 User Manual Page 12 of 51
2-3. IO Ports View
D84U / F34 / F84U Motherboard
a b c d e f g h i
No.
Description
a
FeDP (2
nd
display)
b
LAN
c
DC 19V in
d
USB 2.0 x 2
e
USB Type C x 2
f
USB 3.0 x 2
g
COM x 2
h
Cash drawer
i
FeDP (Main display)
F14 Motherboard
a b c d e f g h i
No.
Description
a
FeDP (2
nd
display)
b
LAN
c
DC 19V in
d
USB 2.0 x 2
e
USB Type C
f
USB 3.0 x 2
g
COM x 2
h
Cash drawer
i
FeDP (Main display)

Element CA850 User Manual Page 13 of 51
2-4. System Dimensions
368.8mm
200mm
348.4 mm
233.7 mm

Element CA850 User Manual Page 14 of 51
3-1. Install the Power Adapter
The system is equipped with a 90W power adapter. Please plug it into the system as
shown below.
1. Find the DC-in connector located
onthe bottom of the system.
(Refer to Chapter 2-3).
2. Plug the cable directly into
the connector then plug the
adapterdirectly into the AC
outlet.
3-2. Remove the System Box
1. Lay down the system to
access the bottom of the
stand.
2. Remove the screws (x2)
and pull the holder of the
systembox outwards.

Element CA850 User Manual Page 15 of 51
3. Disconnect the cable of the
LCDpanel.
4. The system box is placed onto
fourhooks. Lift the system box
and then pull it outwards to
release it from the bottom of
the stand.

Element CA850 User Manual Page 16 of 51
4-1. Install the MSR/ NFC/ iButton/ Fingerprint Module
1. The variety of peripherals MSR, NFC, iButton, and Fingerprint modules
can beinstalled to each side of the system depends on your preference.
2. Press to remove the dummy cover and then loosen the screws (x2).
3. Position the MSR module and fasten the screws (x2) on the back to secure
themodule.
4. Attach the top cover of the MSR module and make sure it locks in place.

Element CA850 User Manual Page 17 of 51
4-2. Install the Customer Display
1. To install the customer display, replace the hinge cover with the one which has an
opening in the top.
Removing the hinge cover : The cover attaches magnetically to the hinge. Pull the
top side of the cover outwards first and then release the rest part of the cover
toseparate it from the hinge.
Installing the hinge cover : To install the hinge cover, angle the hinge cover so that
the bottom side is inserted first into the torque hinge. Then press the top side of the
3. Attach the customer display and fasten it into place with the screws (x2) provided.
cover into place.
2. Connect the customer display cable
(x1) to the connector on system side.

Element CA850 User Manual Page 18 of 51
4-3. Install the Second Display
Accessories items
a. 11.6" or 15.6" 2nd display
module
b. Top arm cover
c. Bottom arm cover
d. Hinge cover
e. Screws for 2
nd
display arm x 5
f. Screws for top arm cover x 4
g. Screws for bottom arm cover x 2
a b c
d e f g
1. Remove the stand cover by pulling it upwards.
2. Attach the 11.6" or 15.6" 2nd display module to the system and route
the 2nddisplay cable through the hole of the stand as picture shown.
3. Fasten the 2nd display module in place with the screws (x5) provided.
4. Slide the top arm cover.

Element CA850 User Manual Page 19 of 51
5. Secure the top arm cover by fastening the screws (x4) from underneath.
6. Attach the bottom arm covers (x2) and fasten the screws (x2).
7. Follow steps 1 and 2 described in Chapter 3-2 to release the holder of the
systembox. Thread the 2nd display cable through the opening and connect
the host endof the cable to FeDP port. (Refer to Chapter 2-3 a).
8. Finally attach the hinge cover.

Element CA850 User Manual Page 20 of 51
4-4. Install the Table Mount Kits
Accessories items
1. Attach the wall mount brackets
to the right and left sides of
themotherboard box.
2. Insert the thumb screws (x4)
through the respective slit of
the bracket so as to adjust the
heightof the motherboard box.
Motherboard box
Wall mount brackets x2
Thumb screws x2
3. Position the wall mount kits under
the table and fasten with the
screws (x4) to secure.