ELGA MEDICA Pro EDI User manual

MEDICA Pro EDI
Operator Manual

ELGA MEDICA Pro EDI Operator Manual
MEDICA Pro EDI MANU39885 Ver 1 –05/12 Page 1
Copyright Note
The information contained in this document is the property of VWS
(UK) Ltd. and is supplied without liability for errors or omissions.
No part of this document may be reproduced or used except as
authorized by contract or other written permission from VWS Ltd.
The copyright and all restrictions on reproduction and use apply to
all media in which this information may be placed.
VWS Ltd. pursue a policy of continual product improvement and
reserve the right to alter without notice the specification, design,
price or conditions of supply of any product or service.
© VWS (UK) Ltd. 2012
All rights reserved.
Publication ref: MANU39885
Version 1 –05/12

MEDICA Pro EDI Operator Manual ELGA
Page 2 MEDICA Pro EDI MANU38995 Ver 1 –05/12
TABLE OF CONTENTS
1. INTRODUCTION ..................................................................3
1.1 Use of this Manual.......................................................3
1.2 Customer Support .......................................................3
1.3 HEALTH AND SAFETY NOTES.................................3
1.4 Electricity.....................................................................3
1.5 Pressure......................................................................3
1.6 Hydrogen.....................................................................4
1.7 Sanitization Chemicals................................................4
1.8 Control of Substances Hazardous to Health (COSHH)4
1.9 Consumables. .............................................................4
2. INSTALLATION AND COMMISSIONING ............................5
2.1 Installation ...................................................................5
2.2 Commissioning............................................................5
3. CONTROLS .........................................................................6
3.1 User Recognition Keys................................................7
3.2 System Preferences....................................................7
3.3 Setting Consumable Replacement Reminders.........15
4. OPERATION ......................................................................17
4.1 Night service/Operational day (screen 030)..............17
4.2 Continuous Recirculation (24/7) (screen 029) ..........17
5. MAINTENANCE..................................................................18
5.1 Replacing Composite Vent Filter (L136)...................18
5.2 Replacing Purification Cartridge LC207 or Conditioning
Cartridge LC206........................................................19
5.3 Replacing Ultra-Microfilter (LC109)...........................20
5.4 Replacing UV lamp (LC105) .....................................21
5.5 Replacing Protek L2 (LC177) or Carbon Filter (LC123)
Pre-treatment. ...........................................................22
5.6 Replacing E- Cartridge (LC181)................................23
5.7 RO modules ..............................................................23
6. SANITIZATION ...................................................................24
6.1 RO sanitization (Step 1)............................................24
Set Sanitization reminder ....................................................25
6.2 Sanitization chemical safety data..............................26
7. EMERGENCY BYPASS......................................................27
7.1 Emergency bypass....................................................27
7.2 Calculation for DI Cartridge (LC207) Cartridge life ...28
8. TROUBLE SHOOTING.......................................................29
9. KEY TO CONTROL PANEL...............................................30
10. TECHNICAL SPECIFICATION...........................................31
11. WARRANTY/CONDITIONS OF SALE ...............................33
12. USEFUL CONTACT DETAILS...........................................35

ELGA MEDICA Pro EDI Operator Manual
MEDICA Pro EDI MANU39885 Ver 1 –05/12 Page 3
INTRODUCTION
1.1 Use of this Manual
ELGA LabWater strives to produce manuals that are as simple and
accurate as possible. However, should you feel they can be
improved in any way please email us at inf[email protected]
This manual guides you through the installation, commissioning and
basic operation of the MEDICA Pro EDI allowing you to obtain a
guaranteed supply of purified water to meet your requirements. For
more detailed information refer to the Operator Manual supplied on
CD.
1.2 Customer Support
Service support and consumable items are available from your local
supplier or distributor. Please contact inf[email protected] for
further information.
1.3 HEALTH AND SAFETY NOTES
WARNING! WARNINGS ARE GIVEN WHERE
FAILING TO OBSERVE THE
INSTRUCTIONS COULD RESULT IN
INJURY OR FATALITY.
CAUTION! Cautions are given where failure to
observe the instructions could result
in damage to the equipment,
associated equipment and
processes.
1.4 Electricity
It is essential that the electrical supply to the MEDICA Pro EDI is
isolated before any items are changed or maintenance work
performed.
The appliance coupler (mains lead) connected to the rear of the unit
can be removed to isolate the power supply. If access to this is
restricted then it is recommended that access to the supply socket is
easily available to disconnect the electrical supply.
The unit must be earthed. Use of the recommended appliance
coupler will ensure adequate earth protection.
WARNING! IF THE EQUIPMENT IS USED IN A
MANNER NOT SPECIFIED BY ELGA,
THE PROTECTION PROVIDED BY
THE EQUIPMENT MAY BE IMPAIRED.
1.5 Pressure
The water supply should be isolated and residual pressure released
prior to removal of any components or carrying out work on the unit.
Switch off the process and relieve pressure in the distribution loop by
opening a point of use or dispense tap.

MEDICA Pro EDI Operator Manual ELGA
Page 4 MEDICA Pro EDI MANU38995 Ver 1 –05/12
1.6 Hydrogen
Small quantities of Hydrogen gas are present in the drain line. Drain
must be in a ventilated area.
1.7 Sanitization Chemicals
During the automatic sanitization cycles, CT3 tablets are used and
relevant safety information is included in this handbook. A safety
data sheet conforming to COSHH regulations is also provided with
the disinfectant and should be read before any tablets are used.
1.8 Control of Substances Hazardous to Health
(COSHH)
Material safety data sheets covering the various replaceable
components are available upon request. Contact your local ELGA
LabWater distributor.
1.9 Consumables.
Consumables
Typical
Service Life*
Max. Shelf
Life
LC105 (UV lamp)
12 months
5 years
LC109 (UMF)
12 months
2 years
LC136 M2 (Vent filter)
6 months
2 years
LC207 (DI Cartridge)
3-12 months
2 years
LC206 (Conditioning Cartridge)
2-6 months
2 years
LC 177 (Protek L2)*
12 months
2 years
LC193 (RO cartridge 120 L/hr)
3 years
2 years
LC181 (E-Cartridge)
3 years
2 years
CT3 (Sanitization tablet)
Typical usage
10 tablets per
month
2 years
* Service Life is an estimate only, and will depend on the
application and feed water quality. Care should be taken to order
the correct consumable items.
* Restricted use based on feed water conditions. Refer to technical
specification on page 31.
LC105
LC207
LC177
LC136
LC181
LC109
LC206

ELGA MEDICA Pro EDI Operator Manual
MEDICA Pro EDI MANU39885 Ver 1 –05/12 Page 5
2. INSTALLATION AND
COMMISSIONING
2.1 Installation
The unit is supplied with a quick start manual that allows the unit to
be quickly installed and commissioned.
It is recommended that a trained ELGA representative carry out the
installation of the product.
2.2 Commissioning
The unit is supplied with the software set in a commissioning mode
that must be completed before being used to supply the application.
It is recommended that a trained ELGA representative complete the
installation of the product.

MEDICA Pro EDI Operator Manual ELGA
Page 6 MEDICA Pro EDI MANU38995 Ver 1 –05/12
3. CONTROLS
The MEDICA Pro EDI control panel has a range of control icons.
General icons are as follows. Further icons are described in the
appropriate sections a complete listing is included in Section 9.
BUTTON
ICON
Function
PROCESS
Turns the unit on/off
LEFT
Menu
Scroll
Shift
Up
CENTRE
✔
Accept
Replacement dates
RIGHT
Mute Alarm
Down
Control panel

ELGA MEDICA Pro EDI Operator Manual
MEDICA Pro EDI MANU39885 Ver 1 –05/12 Page 7
3.1 User Recognition Keys
Your unit is supplied with the following User keys:
Master Key (Black) 1off
User Key (Blue) 4off
Sanitization Key (Green) 2off
The Master Key should be stored in a safe place. The Master Key
controls the access level of the other User Keys.
User Keys only have access to customer preference screens.
Sanitization Keys start the sanitization process and stop the general
user from accidentally starting sanitization.
CAUTION! If the Master Key is lost a new Key can only
be programmed by ELGA Service
Engineers.
3.2 System Preferences
When the MEDICA Pro EDI unit is started for the first time after
completing the commissioning routine the following steps should be
carried out to set up your choices:
Note: Your choices can be changed and implemented
during normal operation. It is not necessary to stop
the unit.
Step 1 - System access (User Key)
The User Key prevents unauthorized access to specific
settings. This ensures consistent system performance and
operation.
Note: The User Key does not prevent access to the
PROCESS function in case of emergency.
1. SWITCH on the main electrical supply to start the
controller set-up sequence. This takes several
seconds.
PRESENT the „Master Key‟ (black) or the „User key‟ (blue)
to the reader ensuring clean contact of both metallic
components.
The display will show a padlock
REMOVE „Key‟ from the reader.
The display will show a key
PRESS button.
Note: If no buttons are pressed the system will relock
after 5 seconds
Present the Master or User Key

MEDICA Pro EDI Operator Manual ELGA
Page 8 MEDICA Pro EDI MANU38995 Ver 1 –05/12
Step 2 - Clock (screen 018)
1. PRESS to edit time
OR
PRESS ✔to proceed to step 3.
2. PRESS and HOLD to increase or to decrease
hour.
3. PRESS to step cursor onto minute.
4. PRESS to increase or to decrease minutes.
5. PRESS ✔.
Step 3 - Date (screen 019)
The date is used to initiate change reminders, the date will
appear on printed records.
1. PRESS to edit date
OR
PRESS ✔to proceed to step 4.
2. PRESS and HOLD to increase or to decrease
day.
3. PRESS to step cursor onto month.
4. PRESS to increase or to decrease month.
5. PRESS to step cursor onto year.
6. PRESS to increase or to decrease year.
7. PRESS ✔
Step 4 - Audible alarm enabled/disabled (screen 020)
This screen provides the option of either turning on the
audible alarm, causing it to sound (while the alarm icon
flashes) or turning off the audible alarm meaning it will
remain quiet
1. PRESS to change mode (= ON)
OR
PRESS ✔to proceed to step 5.
2. PRESS ✔.
Note: The visual alarm cannot be disabled.
Audible alarm enable screen
Set date screens
Setting clock time

ELGA MEDICA Pro EDI Operator Manual
MEDICA Pro EDI MANU39885 Ver 1 –05/12 Page 9
Step 5 –Set units of measure - Volume (screen 021)
This screen allows units of water volume to be set, to
either Litres or US Gallons. This only indicates the
volume in the reservoir.
1. PRESS to change (L or USG)
OR
PRESS ✔to proceed to step 6.
2. PRESS ✔.
Step 7 - Water purity unit setting (screen 023)
This screen allows preferred displayed units of water purity
to be set, to either, M.cm or µS/cm. This only affects the
quality measurement in the recirculation loop.
1. PRESS SCROLL to change mode (M.cm or
µS/cm)
OR
PRESS ✔to proceed to step 8.
2. PRESS ✔.
Step 8 - Uncompensated water quality (screen 024)
A U will indicate uncompensated readings (recirculation
loop only) in the normal process screen.
1. PRESS to change (= Uncompensated water
quality ON)
OR
PRESS ✔to proceed to step 9.
2. PRESS ✔.
Note: This mode is for validation purposes only
and should not be selected as standard.
Uncompensated water quality
screen
Set units of measure - volume
Water purity unit setting

MEDICA Pro EDI Operator Manual ELGA
Page 10 MEDICA Pro EDI MANU38995 Ver 1 –05/12
Step 9 - RO water quality alarm settings QS1 (screen 025)
This screen is used to set the value at which the RO water
quality alarm will sound. This alarm does not stop RO
production but can extend or start flush routines.
1. PRESS to select alarm point (Increments of 10,
ranging from 20 to 100µS/cm).
If „0‟ is selected the alarm will be turned „OFF‟.
OR
PRESS ✔to proceed to step 10.
2. PRESS ✔.
Step 10 - Product water purity alarm settings QS2 (screen 026)
This screen is used to select the value at which the product
water purity alarm will activate. The alarm does not stop
the unit and will automatically reset if the purity level
recovers
1. PRESS to select alarm point (increments of 1,
ranging from 1 to 10 M.cm).
OR
PRESS ✔to proceed to step 11.
2. PRESS ✔.
Step 11 - RO water temperature alarm settings TS1 (screen
027)
This screen is used to select the value at which the RO
water temperature alarm will activate. The alarm does not
stop the unit and will automatically reset if the temperature
returns below the set point.
1. PRESS to select alarm point (increments of 1,
ranging from 20 to 50C)
OR
PRESS ✔to proceed to step 12.
2. PRESS ✔.
Alarm settings TS1 screen
Alarm settings QS1 screen
Alarm settings QS2 screen

ELGA MEDICA Pro EDI Operator Manual
MEDICA Pro EDI MANU39885 Ver 1 –05/12 Page 11
Step 12 - Product water temperature alarm settings TS2 (screen 028)
This screen is used to select the value at which the product water
temperature alarm will activate. The alarm does not stop the unit
and will automatically reset if the temperature returns below the
set point.
1. PRESS to select alarm point (increments of 1, ranging
from 20 to 50C)
OR
PRESS ✔to proceed to step 13.
2. PRESS ✔.
Note: If the water temperature rises above 55  C in the system
it will alarm, stop and await operator intervention - alarm
will be reset once power is removed for 5 seconds and
then reinstated
Step 13 - Continuous operation (screen 029)
Continuous operation may be required in particular circumstances
or when demand for water fluctuates.
CAUTION! During long periods of continuous operation and
low usage the water temperature will rise. It is
recommended that this function is only used
when water usage is on average >50 litres/hr and
water is used every day.
1. PRESS to change (= ON)
OR
PRESS ✔to proceed to step 14.
Note: Proceed to step 16 if continuous operation is selected
(= ON).
Step 14 - Periods of operation (screen 030)
For efficiency and to reduce the likelihood of heat build up the
normal operational hours can be selected.
During „OFF‟ periods the unit will automatically re-circulate water
for a period of 10 minutes every two hours this will maintain water
purity within the distribution loop.
1. PRESS to edit night service start
OR
PRESS ✔to proceed to step 15.
2. PRESS to increase or to decrease time in increments
of 30 minutes.
3. PRESS to step to night service end.
4. PRESS to increase or to decrease time in
increments of 30 minutes.
5. PRESS to enter times.
6. PRESS ✔.
Note: Night service will only be operational if Continuous
Operation is not enabled.
Setting period of operation
Continuous operation screen
Alarm settings TS2 screen

MEDICA Pro EDI Operator Manual ELGA
Page 12 MEDICA Pro EDI MANU38995 Ver 1 –05/12
Step 15 - Operational days selection (screen 031)
Select the days that the MEDICA Pro EDI is required to
operate by highlighting the relevant box.
Monday = 1, Sunday = 7
1. PRESS to enter selection screen
OR
PRESS ✔to proceed to step 14.
2. PRESS to highlight box 1 (= Monday enabled)
OR
PRESS to step to box (2).
Note: A highlighted box indicates that the unit will be
operational on that day between the times set in
step 14.
3. REPEAT, step 15 - item 2, to select further operating
days or PRESS until the ✔appears.
4. PRESS ✔.
Note: During the selected off periods the unit can be
restarted by pressing PROCESS. A few minutes
operation should be allowed before use to allow
water purity to reach a high.
Step 16 - Display viewing angle adjustment (screen 032)
The angle of the display can be adjusted up and down for
better viewing of the screen.
1. PRESS and HOLD or to adjust the viewing
angle
OR
PRESS ✔to proceed to step 17.
2. PRESS ✔.
Viewing angle adjustment screen
Day selection screen

ELGA MEDICA Pro EDI Operator Manual
MEDICA Pro EDI MANU39885 Ver 1 –05/12 Page 13
Step 17 - Auto-restart (screen 033)
This allows selection of the AUTO restart option. If auto
restart is selected the unit will automatically restart after a
power failure. In manual mode the unit will stay in standby
after a power failure.
1. PRESS to change mode (= ON)
OR
PRESS ✔to proceed to step 18.
2. PRESS ✔.
Step 18 - Feed Water Quality (screen 034)
An indication of the RO performance can be obtained
using a calculation of ionic rejection in which the
conductivity of the permeate is compared to that of the
feedwater.
Enter the feedwater conductivity to obtain an accurate
measurement.
1. PRESS to reduce the value to the correct reading
2. PRESS ✔to accept
Step 19 - Data output (screen 035)
The MEDICA Pro EDI can transmit operational data to an
Xport storage device.
1. PRESS to format the storage device.
OR
PRESS ✔to proceed to step 20.
2. PRESS ✔.
Step 20 - Data transmit (screen 036)
Setting the frequency of data transmittals to Xport.
1. PRESS to change transmit intervals (1, 5, 15,
30min / 1,6 hour)
OR
PRESS ✔to proceed to step 21.
2. PRESS ✔.
Note: PRESS PRINT during normal operation and
current data will be transmitted if data output (035)
is selected.
Auto-restart screen
Data transmit screen
Feed Water Quality Screen
Data output screen

MEDICA Pro EDI Operator Manual ELGA
Page 14 MEDICA Pro EDI MANU38995 Ver 1 –05/12
Step 21 - Programming of User Keys (screen 037)
During the life of the MEDICA Pro EDI you may need to
delete or add User keys to prevent or allow access to user
choices. This feature is only available to the Master key
holder.
CAUTION! Do not press reset unless all User Keys
are present.
1. PRESS to delete all User keys
2. PRESENT the new User key to the reader.
3. PRESS to load new User key identification.
4. REPEAT instruction 2 and 3 until all User keys are
registered (maximum of 6 users).
5. PRESS ✔to complete settings.
Step 22 - Programming of Sanitization Keys (screen 038)
Sanitization Keys are required to start a Sanitization.
These keys can be deleted or added.
1. PRESENT Master key to the reader
2. PRESS ✔until the Sanitization Key programming
screen appears.
3. PRESS to delete all Sanitization keys
4. PRESENT the new Sanitization Key to the reader.
5. PRESS to load new Sanitization key identification.
6. REPEAT instruction 4 and 5 until all Sanitization keys
are registered (maximum of 2 users).
7. PRESS ✔to complete settings.
Programming of Sanitization Keys screen
Programming of user keys screen

ELGA MEDICA Pro EDI Operator Manual
MEDICA Pro EDI MANU39885 Ver 1 –05/12 Page 15
3.3 Setting Consumable Replacement Reminders
Step 1 - Enter consumable replacement timer set-up
1. TURN unit off at electrical supply.
Note: Allow time for the display to go blank after the
power is removed.
2. SWITCH electrical supply on.
3. PRESENT Master Key and PRESS button to enter
the Consumable Timer set up.
Step 2 –Purification Pack (LC207) replacement date
1. PRESS button to reset cartridge replacement date
OR
PRESS ✔to accept replacement date and proceed to
CVF Reminder.
2. PRESS ✔to confirm that resetting is required
OR
PRESS ✗to abort reset.
3. PRESS ✔.
Step 3 –Composite Vent filter (CVF) LC136M2 replacement
date
1. PRESS button to reset CVF replacement date
OR
PRESS ✔to accept date and proceed to UV lamp
Reminder.
2. PRESS ✔to confirm that resetting is required
OR
PRESS ✗to abort reset.
3. PRESS ✔.
Step 4 - UV lamp (LC105) replacement date
1. PRESS button to reset UV lamp replacement date
OR
PRESS ✔to accept replacement date and proceed to
Protek Filter Replacement.
2. PRESS ✔confirm that resetting is required
OR
PRESS ✗to abort reset.
3. PRESS ✔.
DI LC207 replacement date screen
CVF replacement date screen
UV replacement date screen

MEDICA Pro EDI Operator Manual ELGA
Page 16 MEDICA Pro EDI MANU38995 Ver 1 –05/12
Step 5 –Protek L2 (LC177).
1. PRESS button to reset Protek L2 (LC177)
replacement date
OR
PRESS ✔to accept replacement date and proceed to
UMF replacement.
2. PRESS ✔confirm that resetting is required
OR
PRESS ✗to abort reset.
3. PRESS ✔.
Step 6 –UMF (LC109) replacement date
1. PRESS button to reset UMF replacement date
OR
PRESS ✔to accept replacement date and proceed to
Sanitization reminder.
2. PRESS ✔confirm that resetting is required
OR
PRESS ✗to abort reset.
3. PRESS ✔.
Step 8 –Conditioning Cartridge (LC206) reminder
1. Press button to reset cartridge replacement date
OR
Press ✔to accept replacement date and complete
settings.
2. PRESS ✔confirm that resetting is required
OR
PRESS ✗to abort reset
3. PRESS ✔.
Step 7 - Sanitization reminder
1. PRESS button to reset Sanitization replacement
date
OR
PRESS ✔to accept replacement date and complete
settings.
2. PRESS ✔confirm that resetting is required
OR
PRESS ✗to abort reset.
3. PRESS ✔.
Pre-treatment cartridge replacement screen
UMF replacement date screen
Sanitization reminder screen
Conditioning Cartridge reminder screen

ELGA MEDICA Pro EDI Operator Manual
MEDICA Pro EDI MANU39885 Ver 1 –05/12 Page 17
4. OPERATION
4.1 Night service/Operational day (screen 030)
Refer to Section 3.2 - Step 14 and 15.
Your MEDICA Pro EDI can be programmed to operate on specific
days between selected times. This is to optimize the efficiency of the
unit and to minimize rises in water temperature.
During the „sleep‟ period the unit will display .
It is possible to override this mode by PRESSING .
During the „sleep‟ period the unit will run in intermittent recirculation
(10 minutes every two hours) to maintain water purity around the
distribution loop.
4.2 Continuous Recirculation (24/7) (screen 029)
Refer to Section 3.2 - Step 13.
If the unit is set to continuous recirculation, it will constantly re-
circulate the water and fill the reservoir as required.
It is recommended that the system only runs in continuous mode
when the demand for water is high (greater than 50% of the make up
flow)
During recirculation the water temperature will tend to increase
slowly.
Night service/Operational day screen

MEDICA Pro EDI Operator Manual ELGA
Page 18 MEDICA Pro EDI MANU38995 Ver 1 –05/12
5. MAINTENANCE
An approved supplier or distributor should carry out any
maintenance work not included in this handbook.
Note: Disposal of all end of life consumable items should
be in accordance with local statutory regulations
WARNING! ALWAYS CHECK THAT THE MAINS
ELECTRICAL POWER AND FEED WATER
ARE SWITCHED OFF BEFORE ATTEMPTING
ANY MAINTENANCE PROCEDURE.
5.1 Replacing Composite Vent Filter (L136)
The Composite Vent Filter (CVF) should be replaced in the
following circumstances:
When indicated by the alarm (screen prompt) or after a
maximum of six months.
1. ENSURE process is OFF and isolate power.
2. OPEN front doors and locate CVF.
3. UNSCREW old CVF and discard
4. UNPACK new CVF.
5. WRITE the installation date on the label of the filter for
future reference.
6. INSTALL filter.
7. SWITCH on power.
8. RESET consumable reminder as described in Section 3.3,
Step 3.
CVF position
General View
CVF
LC109
LC206
LC207
LC181