Eliminator Lighting Electro Panel 192 User manual

Electro
Panel 192
SPECIFICATIONS:
Model: Electro Panel 192
LEDs: 192 - 64 Red, 64 Green,
& 64 Blue
Weight: 4.6lbs./ 2.1kgs.
Size: 7.12” (H) x 12.41” (W) x
4.5” (D)
Fuse: 2 Amp
Supply Voltage: 120V
Working Position: Any Safe position
Duty Cycle: None
DMX Channels: 6 DMX Channel Modes:
1, 2, 3, 4, 6, or 7 DMX
Channels
Colors: Multiple Colors
Warranty: 1 Year
CAUTION! Please read and
understand these instructions
before installing or operating
this unit.
Operating Instructions:
The Electro Panel 192 has been tested at the
factory, there is no assembly required. The
unit is ready to be plugged into a power out-
let. This unit is a 7 channel DMX intelligent
LED par can. It can be run as a stand-alone,
static unit DMX controlled unit, or in a Master/
Slave configuration. While in Stand Alone or
a Master/Slave configuration, you can run
the auto mode. For stand-alone mode, and
Master/Slave configuration settings, see other
side.
©Eliminator® Los Angeles, CA. - www.EliminatorLighting.com
Caution! Never open unit when in use.
Always disconnect main power before
replacing fuse. Remember to always
replace with the exact same type fuse.
1 Year Limited Warranty: Eliminator Lighting warranty is valid from the date of purchase. Our
1 year limited warranty covers manufacturing defects only. Serial number, place of purchase with
dated valid receipt must be submitted at time of service. Eliminator Lighting warranty does not cover
items or parts prone to wear and tear: lamps, fuses, brushes and belts. Eliminator Lighting warranty
is only valid with-in the United States.

ADDR - DMX Address Setting.
1. Tap the either the MENU, UP, or DOWN buttons until “ADDR” is displayed, press ENTER.
2. “1” will now be displayed and ashing. Press the UP or DOWN buttons to nd your desired
address. Press ENTER to set your desired DMX address.
CHND - There are 6 DMX Channel modes to choose from, this will let you switch and select
your DMX Channel mode. You can choose from either 1, 2, 3, 4, 6, or 7 DMX Channels. Please
see the last page of the DMX values and traits for each DMX Channel Mode.
1. Tap the either the MENU button until “CHND” is displayed, press ENTER.
2. Tap the UP or DOWN buttons to scroll through the different DMX Channel modes. Once you have
found your desired DMX Channel mode press ENTER to conm and exit.
SLND - This will let you set unit as a master or slave in a master/slave conguration.
1. Tap the either the MENU button until “SLND” is displayed, press ENTER. “MSTR”, “SL 1” or “SL 2” will
be displayed.
2. Tap the UP or DOWN buttons until your desired setting is displayed, press ENTER to conm and
exit.
SHND - in this mode you can choose and run one of 11 preprogrammed shows.
1. Tap the either the MENU button until “SHND” is displayed, press ENTER.
2. Tap the UP or DOWN buttons to scroll through 11 preprogrammed shows.
3. Select your desired show by pressing the ENTER button to conrm and exit.
DIMM - in this mode you can set the brightness/intensity of the xture.
1. Tap the either the MENU button until “DIMM” is displayed, press ENTER.
2. Tap the UP or DOWN buttons to adjust the brightness (0-255). A setting of 0 will not produce any
light output
3. Select your desired intensity by pressing the ENTER button to conrm and exit.
STRO - in this mode you can activate and set the strobe rate.
1. Tap the either the MENU button until “STRO” is displayed, press ENTER.
2. Tap the UP or DOWN buttons to adjust the stobe rate (0-255). A setting of 0 will deactivate the
strobe feature.
3. Select your desired strobe rate by pressing the ENTER button to conrm and exit.
BLND - Blackout or Stand by mode.
1. Tap the either the MENU button until “BLND” is displayed, press ENTER. Either Yes or No will be
displayed.
©Eliminator® Los Angeles, CA. - www.EliminatorLighting.com

2. To activate Blackout tap the UP or DOWN buttons until Yes is displayed, press ENTER to conm
and exit. The xture will now be in Blackout mode. To deactivate Blackout mode, select No and
press Enter.
LED - With this function you can switch the lamp on or off via the control board.
1. Tap the either the MENU button until “LED” is displayed, press ENTER.
2. The display will show either “ON” or “OFF”. Press the UP or DOWN buttons to select “ON” to switch
on the LED, or “OFF” to switch off the LED.
3. Press ENTER to conrm and exit.
I DSP - This function will reverse the display 180º.
1. Tap the either the MENU button until “I DSP” is displayed, press ENTER.
2. Tap the UP button until “FLIP” is displayed.
3. Press ENTER, the display will show “ON/OFF”.
4. Press the UP button to select “ON” to activate this function, or “OFF” to deactivate this function.
5. Press ENTER to conrm.
FHRS - With this function you can display the running time of the unit.
1. Tap the either the MENU button until “FHRS” is displayed, press ENTER.
2. The display shows the running time of the unit. Press MENU to exit.
VER - Use this function to display the Software version of the unit.
1. Tap the either the MENU button until “VER” is displayed, press ENTER.
2. The display will show the software version.
©Eliminator® Los Angeles, CA. - www.EliminatorLighting.com

©Eliminator® Los Angeles, CA. - www.EliminatorLighting.com